Miele PW 6080 EL AV User manual

11.09 Mat. no. 07 780 680 / 01
Installation recommendations
Washer-extractor
PW 6080 EL AV/LP
en - GB

Mat. no. 07 780 680 / 01
2
It is essential to read the operating and installation instructions before
installing, commissioning or using the machine.
This avoids the risk of accidents or damage.
All rights reserved

Technisches Datenblatt / Technical datasheet: PW 6080 EL AV/LP
Datum / Date: 28.10.2009 Seite / Page: 8
Technical Datasheet
Washer-extractor:
Heating:
PW 6080 AV/LP
Electric (EL)
Legend:
Circled, bold-type abbreviations:
Connection required
Abbreviations surrounded by broken circle:
Connection optional or required, depending on model
Optional extras:
UM
Miele plinth
UO 6008 (UO = Open plinth)
Height
mm
305
Width
mm
680
Depth
mm
679
UG 6008 (UG = Closed plinth)
Height
mm
305
Width
mm
692
Depth
mm
685
US 6008 (US = Plinth with drawer)
Height
mm
320
Width
mm
692
Depth
mm
685
BS
Concrete plinth
Concrete plinth (min. quality C12/15)
Recommended height
mm
300
Minimum height
mm
70
Recommended width
mm
≥700
Recommended depth
mm
≥700
It must be ensured that the om-site concrete plinth is
anchored to the floor!
Machine connections:
Electrical
connection
1. Standard voltage (as supplied)
V
3N AC 400
Frequency
Hz
50
Rated load
kW
8.2
Fuse rating
A
3 × 16
Connection cable cross-sectional area
mm²
5 × 1.5
Connection cable length
mm
2000
Connection cable without plug
(supplied as standard)
Country variations:
1. Standard voltage (as supplied)
V
1N AC 220 - 240
Frequency
Hz
50
Rated load
kW
5.05 –6.0
Fuse rating
A
1 × 25
Connection cable cross-sectional area
mm²
3 × 2.5
Connection cable length
mm
2000
Connection cable without plug
(supplied as standard)
1. Standard voltage (as supplied)
V
3 AC 230
Frequency
Hz
50
Rated load
kW
8.2
Fuse rating
A
3 × 20
Connection cable cross-sectional area
mm²
4 × 2.5
Connection cable length
mm
2000
Connection cable without plug
(supplied as standard)

Technisches Datenblatt / Technical datasheet: PW 6080 EL AV/LP
Datum / Date: 28.10.2009 Seite / Page: 9
Non-standard voltages:
OS 440
1. Standard voltage (as supplied)
V
3 AC 440
Frequency
Hz
60
Rated load
kW
7.9
Fuse rating
A
3 × 16
Connection cable cross-sectional area
mm²
4 × 1.5
Connection cable length
mm
2000
Connection cable without plug
(supplied as standard)
Electrical connection must be in accordance with local and
national regulations.
Plug and socket connection in accordance with IEC/EN
60309 and IEC/EN 60947 recommended to facilitate
electrical safety tests.
If the machine is connected via a fixed connection, a multi-
pole switch must be provided on site to ensure complete
isolation. Switches with a contact opening of more than 3 mm
should be used. Such switches are, e.g., LS switches, fuses
and contactors (IEC/EN 60947).
A wall socket or mains isolator must be visible and accessible
after installation.
A new connection, modification of an existing installation or
earth checking, including the determination of suitable fuse
rating, may only be carried out by a suitably qualified
electrician in accordance with all local and national
regulations.
Cold water
(soft water)
Min. flow pressure
kPa
100
Max. pressure
kPa
1000
Max. throughput
l/min
11
On-site connection thread according to DIN 44 991
Inch
¾" external thread
Length of connection hose
(parts supplied: 1 connection hose)
mm
1550
Water requirements (average for 60°C programme)
With standard connection (with hot water)
l/h
Approx. 70
If hot water supply is not available, a sufficient supply of cold
water must be ensured.
If connected to an alternative water supply (optional), subtract
cold water volume.
Hot water
(soft water)
Max. temperature
°C
70
Min. flow pressure
kPa
100
Max. pressure
kPa
1000
Max. throughput
l/min
11
On-site connection thread according to DIN 44 991
Inch
¾" external thread
Length of connection hose
(parts supplied: 1 connection hose)
mm
1550
Water requirements (average for 60°C programme)
l/h
Approx. 70
It is possible to connect the machine to a very hot water
supply with temperature from 70°C to max. 85°C. For this a
special connection hose is required. This special hose is
available from the Miele Spares Dept.
In addition, the Miele Service Dept. or an authorised dealer
must reprogram the machine accordingly.
If a hot water supply is not available, connect the hot water
hose to a cold water supply!
Alternative water
supply
(Optional)
Min. flow pressure
kPa
100
Max. pressure
kPa
1000
Max. throughput
l/min
11
On-site connection thread according to DIN 44 991
Inch
¾" external thread
Length of connection hose
(parts supplied: 1 connection hose)
mm
1550
Water requirements (average for 60°C programme)
l/h
Not yet available

Technisches Datenblatt / Technical datasheet: PW 6080 EL AV/LP
Datum / Date: 28.10.2009 Seite / Page: 10
Waste water
Model with dump
valve
Max. temperature
°C
70
Machine waste water connection (external diameter)
mm
75 [DN 70]
On-site drain (internal diameter)
mm
75 [sleeve DN 70]
Max. transient throughput
l/min
62
Vented drainage required. If ventilation is insufficient, fit Miele
kit, Mat. no. 05238090.
Drain manifolds serving several machines must be of
sufficient cross-section.
Drainage via
drain pump
Max. temperature
°C
70
Drain hose (inner diameter)
mm
22 [DN 22]
On-site hose sleeve for drain hose
(inner diameter x length)
mm
22 × 30
Max. transient throughput
l/min
26
Max. head height (measured from base of unit)
mm
1000
Vented drainage required. If ventilation is insufficient, fit Miele
kit, Mat. no. 05238090. .
Drain manifolds serving several machines must be of
sufficient cross-section.
Fittings
(supplied)
Miele plinth UG/UO 6008
4 × fasteners (to secure machine to plinth)
4 × screws DIN 571 (Ø × length)
mm
8 × 65
4 × rawl plugs (Ø × length)
mm
12 × 60
Machine must be bolted to the floor!
Fixing materials for floating screed floor to be provided on site
Miele plinth US 6008
4 × fasteners (to secure machine to plinth)
4 × screws DIN 571 (Ø × length)
mm
6 × 50
4 × rawl plugs (Ø × length)
mm
8 × 40
Machine must be bolted to the floor!
Fixing materials for floating screed floor to be provided on site
On concrete plinth
2 × metal brackets
2 × screws DIN 571 (Ø × length)
mm
6 × 50
2 × rawl plugs (Ø × length)
mm
8 × 40
Machine must be bolted to the floor!
Fixing materials for floating screed floor to be provided on site
Machine data
Machine width
mm
700
Machine depth
mm
727
Machine height
mm
1020
Casing width
mm
692
Casing depth
mm
690
Min. access width to installation site
mm
720
Minimum rear wall gap (measured to front of machine)
mm
1100
Minimum wall gap (to front edge of machine)
With an installation with the minimum gap, additional work
may be required when service or repair work is necessary.
mm
900
Net weight
kg
140
Dynamic floor load, max.
N
2600
Static floor load, max.
N
1850
Dynamic load, max.
N
750
Drum frequency, max.
Hz
22
Average heat dissipation
(dependent on ambient room temperature and programme
selected)
W
Not yet available
Sound pressure level (re 20 mPa),
(measured at a distance of 1 m from the machine and at a
height of 1.6 m)
dB (A)
<70
Installation should only be carried out by authorised fitters in accordance with valid regulations!
Observe installation instructions when installing machine! All rights reserved! Dimensions in mm