MIGEL GSI 120 User manual
1
GSI 120
GSI120
2
.A
.B
.C
.D
O
MAX
MIN
CB
D
A
3
4
5
O
1
English
GSI 120
Dear customer!
Thanks for your worthful choce and confdence to Mgel
brand. We really hope that you enjoy operatng ths product
TECHNICAL DATA
Model Power Frequency Voltage
GSI120 750-1200 W 220-240 V 50/60 Hz
Safety Instructions
Cautions of the rst use
1. Before using for the rst time, please check if the voltage rating on the
type plate corresponds to the mains voltage in your home.
2. Make sure to unplug the appliance from the socket when leaving the iron
even for a short while, and stand the iron on its end. Please leave the iron
away from the touch of children..
3. The iron will be of high temperature when used, never touch it with hand
or close to the ammable product in order to avoid the accident.
4. Caution: Unplug the appliance from the socket before lling the iron with
water.
5. Never immerse the iron in water or other liquid.
6. Please send the iron to our special repair agent for repair if any damage
on cord.
7. Deposit or Mineral in the water will lead to generate the scales and block
the seam hole, therefore it is advisable to use distilled water.
8. Do not use chemically descaled water
9. The ejected steam is hot and therefore hazardous. Never direct the steam
towards people.
10. The iron must be used and rested on a stable surface
11. When placing the iron on its stand, ensure that the surface on which the
stand is placed is stable.
12. Do not pull or carry by cord, use cord as a handle, close a door on the
cord, or pull cord around sharp edges or corners, Keep cord away from
heated surfaces.
13. The iron is not to be used if it has been dropped ,if there are visible signs
of damage or if it is leaking.
1. The iron has been greased, and as a result, the iron may slightly smoke
when switched on for the rst time. After a short while, this will cease.
2. Before using for the st time, remove any sticker or protective foil from the
Burst of Steam
This function works well for tough wrinkles and heavy fabrics. By pressing
“Burst of Steam” button,an intense burst of steam is emitted from the
soleplate, this can be very useful when removing stubborn creases. The
shot of steam facility can be used only while ironing with high ironing
temperature. For optimal result, there should be 5 seconds rest between
presses of the steam button. To prevent leaking water from the soleplate
2
1. Set the steam selector to position O(=No Steam)
2. As per washing label of various clothes, set the correct ironing temperature
to begin a ironing.
1. Fill water in the iron as per the water-lling methods.
2. Plug the appliance in the socket.
3. If only set thermostat knob to MAX position as per the temperature
indicator, steam iron will be available, otherwise water may leak from the
soleplate.
4. It indicates that the temperature has been ready until the indicator light
goes o.
5. Set the steam selector correctly, increase steam output by pushing the
steam selector back and decrease steam output by forward.
Component Name
Filling with Water
Dry Ironing
Steam Ironing
A. burst steam button
B. Voltage button
C. steam knob
D. contraction push button
Make sure iron is unplugged and the thermostat dial is in the MIN position.
Take the rubber out and put the water into the small hole of the handle.
soleplate. Clean the soleplate with a soft cloth.
3. Keep the soleplate smooth: avoid hard contact with metal objects.
CB
D
A
3
Type of Fabric and Thermostat knob Dial Form
Please note that on the label means that this article may not
ironed.
Instructions on Label Type of Fabric
Nylon
Silk
Wool
Cotton
Linen
Thermostat Dial
MIN
MAX
Cleaning and Maintenance
Before cleaning, remove the plug from the socket and allow the iron to cool
down suciently.
1. Wipe o the soleplate with a damp cloth and a non-abrasive (liquid)
cleaner.
2. If the ber is adhered to the soleplate, use a damp cloth with vinegar to
wipe o the soleplate.
3. Never use strong acid or alkali in order to avoid damaging the soleplate.
4. If the scale blocks the steam hole, please remove the scale with toothpick;
do not damage the surface of soleplate.
5. Stand the iron on its end and let it cool down suciently, and meantime
pour any remaining water out of the box, set the steam knob to position“O”.
does not press the steam button continuously for more than 5 seconds..
Also allow at least one minute interval before applying this burst of steam
function.
Simple Repair Methods
Problem
Not enough heat
or Too heat
No steam or Leakage
No burst of steam
or no vertical steam
Leaking water from
Soleplate
Little Steam
Possible Reasons
Rotate thermostat
dial improperly or
unplugging
The thermostat dial has
been set to MIN
The(vertical) burst of
steam function has
been used too often
within a very short
period. The iron is not
hot enough.
Set the thermostat dial
out of steam range.
The heat is still not
enough.
The water is over than
max position
Check if the steam
selector is in proper
location.
Steam hole is blocked.
Too little water in the
water tank
Measurement
Correct Thermostat dial
in position and check if
the iron is plugged.
Set the thermostat
dial to the required
positioin.
Continue ironing in
horizontal position and
wait a while before
using the (vertical)
burst of steam function
again.
Set the thermostat dial
as per steam range.
Open steam button
only after the indicator
light goes o.
Pour out the remaining
water
Set the steam selector
to the proper location.
Clean hole with
distilled water.
Fill water into the box
4
5
Read the instructions carefully before use and keep it
1. The appliance is intended fro use by persons with disposing capacity,
experiences and common sense. For those persons who are lack of
guarantee in safety, they must be supervised by their custodians to use the
appliance. Children should be supervised to ensure that they do not play
with the appliance.
2. The iron must not be left unattended while it is connected to the supply
mains
3. The iron must be used and rested on a stable surface
4. When placing the iron on its stand, ensure that the surface on which the
stand is placed stable
5. The iron is not to be used if it has been dropped, if there are visible signs
of damage or it is leaking.
6. The plug must be removed from the socket-outlet .
7. Push the button back of the cover to fold the handle.
Environment
-Do not throw away the appliance with the normal household
waste at the end of its life, but hand it in at an ocial collection
point for recycling. By doing this, you help to preserve the
environment.
Table of contents
Languages:
Other MIGEL Iron manuals
