MIGEL GSI 200 User manual
English
GSI 200
Power: 2200W
Voltage: 220-240V
Frequency:50/60Hz
Dear customer!
Thanks for your worthful choice and condence to Migel brand. We
really hope that you enjoy operating this product.
IMPORTANT SAFEGARDS
TECHNICAL SPECIFICATION
1. Before using for the rst time, please check if the voltage rating on the
type plate corresponds to the mains voltage in your home.
2. Make sure to unplug the appliance from the socket when leaving the
iron even for a short while, and stand the iron on its end. Please leave the
iron away from the touch of children..
3. The iron will be of high temperature when used, never touch it with
hand or close to the ammable product in order to avoid the accident.
4. Caution: Unplug the appliance from the socket before lling the iron
with water.
5. Never immerse the iron in water or other liquid.
6. Please send the iron to our special repair agent for repair if any damage on cord.
7. Deposit or Mineral in the water will lead to generate the scales and block
the seam hole, therefore it is advisable to use distilled water.
8. Do not use chemically descaled water
9. The ejected steam is hot and therefore hazardous. Never direct the
steam towards people.
10. The iron must be used and rested on a stable surface
11. When placing the iron on its stand, ensure that the surface on which
the stand is placed is stable.
12. Do not pull or carry by cord, use cord as a handle, close a door on the
cord, or pull cord around sharp edges or corners, Keep cord away from
heated surfaces
13. The iron is not to be used if it has been dropped ,if there are visible signs
of damage or if it is leaking
14. The appliance is intended fro use by persons with disposing capacity,
experiences and common sense. For those persons who are lack of
guarantee in safety, they must be supervised by their custodians to use
the appliance. Children should be supervised to ensure that they do not
play with the appliance.
15. The iron must not be left unattended while it is connected to the supply mains
16. The iron must be used and rested on a stable surface
17. When placing the iron on its stand, ensure that the surface on which 1
Component
Filling with Water
A: Sole plate F: Burst button K: Thermostat Dial
B: Spray Nozzle G: Handle L: Steam adjuster,self-clean
C: Water tank H: Cord protector
D: Water lling cover I: Back Cover
E: Spray button J: Indicator light
Cautions of the rst use
2
Make sure iron is unplugged and the thermostat dial is in the MIN position.
Place iron on the heel rest, tilt forward approximately 45 angle and pour
water into the water-lling opening to the MAX position of the water tank.
1. The iron has been greased, and as a result, the iron may slightly smoke
when switched on for the rst time. After a short while, this will cease.
2. Before using for the st time, remove any sticker or protective foil from
the soleplate. Clean the soleplate with a soft cloth.
3. Keep the soleplate smooth: avoid hard contact with metal objects.
the stand is placed stable
18. The iron is not to be used if it has been dropped, if there are visible signs
of damage or it is leaking.
19. The plug must be removed from the socket-outlet before the water
reservoir is lled with water(for steam irons and irons incorporating means
for spray water)
20. This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
21. Children should be supervised to ensure that they do not play with the
appliance.
A
B
D
L
E
G
I
F
C
J
H
K
Vertical Steam
Dry Ironing
Steam Ironing
Burst of Steam
3
Burst of Steam”can also be applied when holding the iron in vertical position,
this is useful for removing creases from hanging clothes, curtains, et.
1. Set the steam selector to position O(=No Steam)
2. As per washing label of various clothes, set the correct ironing
temperature to begin a ironing.
1. Fill water in the iron as per the water-lling methods.
2. Plug the appliance in the socket.
3. If only set thermostat knob to MAX position as per the temperature
indicator, steam iron will be available, otherwise water may leak from the
sole plate.
4. It indicates that the temperature has been ready until the indicator
light goes o.
5. Set the steam selector correctly, increase steam output by pushing the
steam selector back and decrease steam output by forward.
Caution: Synthetic Fabric, Nylon, Synthetic Silk and Silk cannot use the
steam iron, otherwise it will damage the nish of surface.
This function works well for tough wrinkles and heavy fabrics. By pressing
“Burst of Steam” button,an intense burst of steam is emitted from the
soleplate, this can be very useful when removing stubborn creases. The
shot of steam facility can be used only while ironing with high ironing
temperature. For optimal result, there should be 5 seconds rest between
presses of the steam button. To prevent leaking water from the soleplate
does not press the steam button continuously for more than 5 seconds..
Also allow at least one minute interval before applying this burst of steam
function.
Spraying Methods
Self-Cleaning
At any temperature by pressing the spray button a couple of times, the laundry
can be damped down. Ensure that there is enough water in the water tank.
Use the self-cleaning function once every two weeks. If the water in your area
is very hard(i.e, when akes come out of the soleplate during ironing),the self-
cleaning function should be used more frequently.). Make sure the appliance is
unplugged, set the steam selector to position“O”, ll the water tank to the MAX
position, do not put vinegar or other dealing agents in the water tank., select
the maximum ironing temperature, put the plug in the wall socket, unplug the
iron when the power indicator lighter has gone out, hold the iron over the sink,
press and hold the self-cleaning button and gently shake the iron to and fro.
4
Type of Fabric and Thermostat knob Dial Form
Caution: on the label means that this article may not ironed.
Instructions on Label Type of Fabric
Nylon
Silk
Wool
Cotton
Linen
Thermostat Dial
MIN
MAX
Cleaning and Maintenance
Before cleaning, remove the plug from the socket and allow the iron to cool
down suciently.
1. Wipe o the soleplate with a damp cloth and a non-abrasive (liquid) cleaner.
2. If the ber is adhered to the soleplate, use a damp cloth with vinegar to wipe
o the soleplate.
3. Never use strong acid or alkali in order to avoid damaging the soleplate.
4. If the scale blocks the steam hole, please remove the scale with toothpick; do
not damage the surface of soleplate.
5. Stand the iron on its end and let it cool down suciently, and meantime pour
any remaining water out of the box, set the steam knob to position“O”.
Steam and boiling water will come out of the soleplate, impurities and akes(if
any),will be ushed out. Release the self-cleaning button as soon as all the
water in the tank has been used up. Repeat the self-cleaning process if the iron
still contains a lot of impurities. After the self-cleaning process, put the plug in
the wall socket and let the iron heat up to allow the soleplate to dry, unplug the
iron when it has reached the set ironing temperature, move the hot iron gently
over a piece of used cloth to remove any water stains that may have formed on
the soleplate, let the iron cool down before you store it
5
Simple Repair Methods
You can help protect the environment!
Please remember to respect the local regulations: hand in the
non-working electrical equipments to an appropriate waste dis-
posal center
ENVIRONMENT FRIENDLY DISPOSAL
Problem Possible Reasons Measurement
Not enough heat or
Too heat
Rotate thermostat dial
improperly or unplugging
Correct Thermostat dial in
position and check if the
iron is plugged.
No steam or Leakage The thermostat dial has
been set to MIN
Set the thermostat dial to
the required positioin.
No burst of steam or
no vertical steam
The(vertical) burst of
steam function has been
used too often within a
very short period. The iron
is not hot enough
Continue ironing in
horizontal position and
wait a while before using
the (vertical) burst of
steam function again
Leaking water from
Soleplate
Set the thermostat dial out
of steam range.
Set the thermostat dial as
per steam range.
The heat is still not enough.
Open steam button only
after the indicator light
goes o.
The water is over than max
position
Pour out the remaining
water
Little Steam
Check if the steam selector
is in proper location.
Set the steam selector to
the proper location.
Steam hole is blocked. Clean hole with distilled water.
Too little water in the
water tank
Fill water into the box
No Spraying
No enough pressure or air
inside
Press the spray nozzle
by hand, and push the
spray button several times
continuously.
Note
-9
رﺎﺨﺑﻮﺗا
-9
ﻪــﺑ و مﺮــﺘﺤﻣ ناراﺪــﯾﺮﺧ لﺎــﺣ هﺎــﻓر ىﺎﺘــﺳار رد (صﺎــﺧ ﻰﻣﺎﻬــﺳ) ﺶــﯿﮐ ﻪﺠﻨــﺳ ﻰــﻧﺎﮔرزﺎﺑ ىﺪــﯿﻟﻮﺗ ﺖﮐﺮــﺷ
ﺶــﺷﻮﭘ ﺖــﺤﺗ ار دﻮــﺧ ﻰــﻗﺮﺑ تﻻﻮــﺼﺤﻣ ،ﺪــﻧا ﻪﺘــﺷاد ﻪــﻋﻮﻤﺠﻣ ﻦــﯾا ﻪــﺑ ﻪــﮐ ىدﺎــﻤﺘﻋا سﺎــﭘ
تﺎــﻣﺪﺧ ى ﻪــﯿﻠﮐ ﻪــﺋارا ﺎــﺑ هاﺮــﻤﻫ ،تﺎــﻌﻄﻗ ﺾــﯾﻮﻌﺗ :ﻞﻣﺎــﺷ ،ﺖــﻧﺎﻤﺿ
.ﺖﺳا هداد راﺮﻗ ،ﺪﯾﺮﺧ ﺦﯾرﺎﺗ زا تﺪﻣ ﻪﺑ تﺎﻌﻄﻗ ﻦﯿﻣﺎﺗ ﻦﯿﻨﭽﻤﻫ و ﻪﻃﻮﺑﺮﻣ
"0"
MIN
MAX
Self-Clean
0
MAX"0"
Self-Clean
MIN
MAX
MAX
GSI 200
Table of contents
Languages:
Other MIGEL Iron manuals
