MikroTik wAP ac Series User manual

wAP ac kit-series
This manual cover wAP ac series models:
wAP ac LTE kit
wAP ac 4G kit
wAP ac LTE6 kit
This device needs to be upgraded to RouterOS v6.46. or the latest version to ensure compliance with local authority regulations.
Note. The information contained here is subject to change. Please visit the product page on www.mikrotik.com for the most up to date version of this
document.
Safety Warnings
Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing
accidents.
Ultimate disposal of this product should be handled according to all national laws and regulations.
All installation methods for mounting an access point on any wall surface is subject to the acceptance of local jurisdiction.
The Installation of the equipment must comply with local and national electrical codes.
This product is intended to be mounted outdoors on a pole but can also be installed indoors. Please read the mounting instructions carefully before
beginning installation. Failure to use the correct hardware and configuration or to follow the correct procedures could result in a hazardous situation to
people and damage to the system.
Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.
Read the installation instructions before connecting the system to the power source.
We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your
own risk!
In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.
It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling
requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

1.
2.
3.
4.
5.
6.
1.
2.
3.
Exposure to Radio Frequency Radiation:This MikroTik equipment complies with the FCC, IC, and European Union radiation exposure limits set forth for an
uncontrolled environment.This MikroTik device should be installed and operated no closer than 45 centimeters from your body, occupational user, or the
general public.
Quickstart
Use a Phillips head screwdriver to loosen the screw, which secures the bottom lid (see ).Bottom Lid
Insert the SIM card into the slot with the chip facing up.
Choose your powering solution, please see the section for possibilities.Powering
Open network connections on your PC and search for the SSID that begins with "MikroTik".
Connect to the wireless network, open in your web browser to start the configuration.https://192.168.88.1
User name: a and there is no password by default you will be logged in automatically to the Quick Set screen. dmin
Update the device by clicking the "Check for updates" button on the right side and updating your RouterOS software to the latest version to
ensure the best performance and stability. Must have a valid SIM card inserted.
To manually update the device, please gohttps://mikrotik.com/download
Choose ARM packages for this device and download them to your PC.
Upload downloaded packages to the WebFig "Files" menu and reboot the device.
Updatingyour RouterOS software to the latest version will ensure the best performance, stability, and security updates.
To personalize your wireless network, SSID can be changed in the fields "Network Name";
Choose your country on the left side of the screen in the field "Country", to apply country regulation settings.
Set up your wireless network password in the field "WiFi Password" the password must be at least eight symbols.
Set up your router password in the bottom field "Password" to the right and repeat it in the field "Confirm Password", it will be used to login next
time.
Click on the "Apply Configuration" to save changes.
MikroTik mobile app
Use the MikroTik smartphone app to configure your router in the field, or to apply the most basic initial settings for your MikroTik home access point.
Scan QR code and choose your preferred OS.
Install and open the application.
By default, the IP address and user name will be already entered.
Click Connect to establish a connection to your device through a wireless network.
Choose Quick setup and the application will guide you through all basic configuration settings in a couple of easy steps.
An advanced menu is available to fully configure all necessary settings.
Powering
The device accepts power from the power jack or from the Ethernet port:
Direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 12-57 V DC;
Ethernet port accepts 802.3af/at PoE 18-57 V DC.
The power consumption under maximum load can reach 16 W. Please attach ground (earth) wire to the screw under the bottom lid.
Connecting to a PoE Adapter:
Connect the Ethernet cable from the device to the PoE+DATA port of the PoE adapter;
Connect an Ethernet cable from your local network (LAN) to the PoE adapter;
Connect the power cord to the adapter, and then plug the power cord into a power outlet.

1.
2.
3.
4.
5.
6.
Mounting
The device can be mounted in several ways: pole, wall, ceiling or it can be placed in a specially designed Mikrotik holder which comes with the package.
The package also includes a drill hole template with detailed mounting instructions, to help you with the Ethernet cable installation and attachment to a
ceiling or a wall. Steel bracket to put on the other side of a dropdown ceiling tile and two screws and wall anchors. Zip ties or steel clamps for mounting on
the pole.
The IP rating scale for this device is IP54. When mounting outdoors, please ensure that any cable openings are directed downwards. We recommend
using the POE injector and proper grounding with Cat6 shielded cable. When using and installing this device please pay attention to the Maximum
Permissible Exposure (MPE) safety distance with a minimum of 35 cm between the radiator and your body.
Mounting on the mast or pole:
* It's recommended to use electrical tape to increase friction between materials.
Mount plastic tie straps to steel brackets guiding them through holes.
Mount bracket to the device.
Secure them with a screw.
Mount and align the device on the pole or mast.
Guide Ethernet cable through the opening and connect to the Ethernet port.
Close bottom latch and secure with a screw.

1.
2.
3.
4.
5.
6.
7.
8.
It's recommended to secure Ethernet cable to the pole using zip ties. With the distance from the device approximately 30 cm.
Mounting unit on the wall:
Use included a template to mark spots for drilling holes. And if needed for Ethernet cable. Align accordingly, it will depend on how the device will
be mounted finally.
Insert dowels if needed, depends on wall structure and material.
Place included a steel bracket on the wall.
Use screws to secure it in place.
Extend your Ethernet cable through the opening and connect to the Ethernet port.
Mount the device on the steel bracket
Secure it in place with the screw.
Close bottom latch.

1.
2.
3.
1.
2.
3.
4.
Avoid mounting the device on the low ground spot, as you won't be able to attach and close the bottom latch.
Mounting on the ceiling:
A Special bracket is included in the package to mount on the drop ceiling. As it consists of two parts, to be attached on both sides of the ceiling tile.
Use the template to mark spots for holes.
Place both mounting brackets on the spot.
Secure them together using screws.
Continue assembling in the same manner if mounting on the wall.
Extend your Ethernet cable through the opening and connect to the Ethernet port.
Mount the device on the steel bracket.
Secure it in place with the screw.
Close bottom latch.
Bottom Lid
The bottom lid is secured in place with the captive screw.
Use the Philips PH2 screwdriver to unscrew it, but do not remove the screw completely.

1.
Pull the cover in the opposite direction from the device to remove it.
Reassemble.
Expansion slots and ports
Integrated two Wireless modules operating at 2.4 GHz and 5 GHz, supporting AP/CPE/P2P/repeater modes.
Two Gigabit Ethernet ports, supporting automatic cross/straight cable correction (Auto MDI/X). Either straight or crossover cable can be used for
connecting to other network devices.
miniPCIe slot and SIM slot (can't be used separately) to be used with a modem.
MiniPCIe slot usage
The device is equipped with a miniPCIe slot with a factory-installed LTE6, LTE, or 4G card. A SIM slot is provided for use together with a miniPCIe modem.
The SIM slot is not used separately. In addition, you can install external antennas of your choice, this should be done by a qualified person, please follow
safety precautions when handling electrical equipment, use a wrist grounding strap when unpacking, and working with electrical components to avoid
electrical discharge (ESD) damage.
To install the external antennas:
Remove the screw using Philips PH2 screwdriver and slide down the bottom lid to remove it;

2.
3.
4.
5.
6.
7.
Remove both screws below the power jack and slide out the wAP PCB board;
Disconnect the grey uFL connector from the MAIN antenna connector of the modem, disconnect the black cable from the other (or AUX)
connector;
Remove two plastic doors using a flat screwdriver or similar tool and feed antenna wires through the holes and connect to the LTE6 card installed;
After you have reinserted the wAP board into the case and secured it with the screw that was removed earlier;
Slide in the SIM card from your mobile operator into the SIM slot, with the chip facing up.
The SIM slot protects the SIM card from falling out with a plastic latch. You can press the latch to the left side to unlock and then insert the SIM
card or replacing it using tweezers or a similar tool.
When using external antennas, please attach connectors to the case:
Make openings and use a 6.5 mm drill bit, and drill in any of four pre-designed spots;
Guide your see the picture below for reference on how to place rubber seals for best water ACSMAUFL connectors and secure them in place,
protection:

SIM slot usage
SIM card slot is designed to use with Micro SIM cards.
Nano SIM cards have different thickness, usage with adapter are not recommended.
Buttons and jumpers
The reset button has three functions:
Hold this button during boot time until the LED light starts flashing, release the button to reset RouterOS configuration (total 5 seconds).
Keep holding for 5 more seconds, LED turns solid, release now to turn on CAP mode. The device will now look for a CAPsMAN server (total 10
seconds).
Or Keep holding the button for 5 more seconds until LED turns off, then release it to make the RouterBOARD look for Netinstall servers (total 15
seconds).
Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device.
Useful for RouterBOOT debugging and recovery.
Configuration
We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best performance and
stability. RouterOS includes many configuration options in addition to what is described in this document. We suggest visiting the RouterOS documentation
page to get yourself accustomed to the possibilities: .https://mt.lv/help
In case an IP connection is not available, the Winbox tool ( ) can be used to connect to the MAC address of the device from the LAN https://mt.lv/winbox
side (all access is blocked from the internet port by default).
It is possible to boot the device from a network, for reinstalling RouterOS for recovery purposes. This can be done from the first Ethernet port. See above
how to do this.
Accessories
The package includes the following accessories that come with the device:

Operating system support
The device supports RouterOS software version 6.46. The specific factory-installed version number is indicated in the RouterOS menu /system resource.
Other operating systems have not been tested.
Notice
The Frequency band 5.470-5.725 GHz isn’t allowed for commercial use.
In case WLAN devices work with different ranges than the above regulations, then a customized firmware version from the manufacturer/supplier
is required to be applied to the end-user equipment and also prevent the end-user from reconfiguration.
For Outdoor Usage: End-user requires approval/license from the NTRA.
Datasheet for any device is available on the official manufacturer website.
Products with the letters “EG” at the end of their serial number have their wireless frequency range limited to 2.400 – 2.4835 GHz, the TX power is
limited to 20dBm (EIRP).
Products with the letters “EG” at the end of their serial number have their wireless frequency range limited to 5.150 – 5.250 GHz, the TX power is
limited to 23dBm (EIRP).
Products with the letters “EG” at the end of their serial number have their wireless frequency range limited to 5.250 – 5.350 GHz, the TX power is
limited to 20dBm (EIRP).
Federal Communication Commission Interference Statement
Please make sure the device has a lock package (firmware version from the manufacturer) which is required to be applied to the end-user
equipment to prevent the end-user from reconfiguration. The product will be marked with country code “-EG”. This device needs to be upgraded
to the latest version to ensure compliance with local authority regulations! It is the end users' responsibility to follow local country regulations,
including operation within legal frequency channels, output power, cabling requirements, and Dynamic Frequency Selection (DFS)
requirements. All MikroTik radio devices must be professionally installed.
To avoid pollution of the environment, please separate the device from household waste and dispose of it in a safe manner, such as in
designated waste disposal sites. Familiarize yourself with the procedures for the proper transportation of the equipment to the designated
disposal sites in your area.

1.
2.
1.
2.
Model FCC ID Contains FCC ID
wAP ac LTE6 kit TV7WAPGR5AC2D TV7R11ELTE6
wAP ac LTE kit TV7WAPGR5AC2D TV7R11ELTE
wAP ac 4G kit TV7WAPGR5AC2D TV7R11E4G
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its
antenna must not be co-located or operation in conjunction with any other antenna or transmitter.
Exposure to Radio Frequency Radiation.IMPORTANT:
This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 45 cm between the radiator and any part of your body.
For use of CBRS bands, the CBSD Category of the final Host equipment will be dependent on the power settings and antenna gain used.
Innovation, Science and Economic Development Canada
Model IC Contains IC
wAP ac LTE6 kit 7442A-WAPGR5AC2D 7442A-R11ELTE6
wAP ac LTE kit 7442A-WAPGR5AC2D 7442A-R11ELTE
wAP ac 4G kit TV7WAPGR5AC2D TV7R11E4G
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada's license-exempt
RSS(s). Operation is subject to the following two conditions:
This device may not cause interference;
This device must accept any interference, including interference that may cause undesired operation of the device.
L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
L'appareil ne doit pas produire de brouillage;
L'appareil doit accepter tout brouillage radioélectrique subi, mźme si le brouillage est.
This ClassB digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-003 (B) / NMB-003 (B)
IMPORTANT: Exposure to Radio Frequency Radiation.
This equipment complies with the IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 45 cm between the radiator and any part of your body.
Cet equipement est conforme aux limites d'exposition au rayonnement IC definies pour un environnement non controle. Cet equipement doit etre installe et
utilise a une distance minimale de 45 cm entre le radiateur et toute partie de votre corps.

The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite
systems.
les dispositifs fonctionnant dans la bande de 5150 ą 5250 MHz sont réservés uniquement pour une utilisation ą l'intérieur afin de réduire les risques de
brouillage préjudiciable aux systčmes de satellites mobiles utilisant les mźmes canaux.
UKCA marking
Eurasian Conformity Mark
Частотный диапазон Мощность передатчика
2400-2483.5 МГц, 5150-5350 МГц, 5650-5850МГц ≤100 мВт
*Доступные частотные каналы могут различаться в зависимости от модели продукта и сертификации.
Информация о дате изготовления устройства указана в конце серийного номера на его наклейке через дробь. Первая цифра означает номер
года (последняя цифра года), две последующие означают номер недели.
Изготовитель: Mikrotikls SIA, Aizkraukles iela 23, Riga, LV-1006, Латвия, [email protected]. Сделано в Китае, Латвии или Литве. Cм. на
упаковке.
Для получения подробных сведений о гарантийном обслуживании обратитесь к продавцу. Информация об импортерах продукции MikroTik в
Российскую Федерацию: https://mikrotik.com/buy/europe/russia
Продукты MikroTik, которые поставляются в Евразийский таможенный союз, оцениваются с учетом соответствующих требований и помечены
знаком EAC, как показано ниже:
Norma Oficial Mexicana
Rango de frecuencia (potencia de salida máxima): 2400-2483.5 (30 ), Los canales de frecuencia disponibles pueden MHz dBm 5725-5850 MHz (30 dBm).
variar según el modelo y la certificación del producto.
EFICIENCIA ENERGETICA CUMPLE CON LA NOM-029-ENER-2017.
La operacion de este equipo esta sujeta a las siguientes dos condiciones:
Es posible que este equipo o dispositivo no cause interferencia perjudicial y.
Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacion no deseada.
Fabricante: Mikrotikls SIA, Brivibas gatve 214i, Riga, LV-1039, Latvia.
País De Origen: Letonia; Lituania; China (Republica Popular); Estados Unidos De America; Mexico.
Por favor contacte a su distribuidor local para preguntas regionales específicas. La lista de importadores se puede encontrar en nuestra página de inicio –
.https://mikrotik.com/buy/latinamerica/mexico

The National Commission for the State Regulation of Communications and
Informatization by Ukraine
Виробник: Mikrotikls SIA, Brivibas gatve 214i Рига, Латвія, LV1039.
Робоча частота (Максимальна вихідна потужність): 2400-2483.5 МГц (20 дБм), 5150-5250 МГц (23 дБм), 5250-5350 МГц (20 дБм), 5470-5725 МГц
(27 дБм).
CE Declaration of Conformity
Manufacturer: Mikrotikls SIA, Brivibas gatve 214i Riga, Latvia, LV1039.
Hereby, Mikrotīkls SIA declares that the radio equipment type RouterBOARD is in compliance with Directive 2014/53/EU. The full text of the EU declaration
of conformity is available at the following internet address: https://mikrotik.com/product
WLAN / WCDMA / LTE / 5G
Operating Frequency / Maximum output power
Betriebsfrequenz / maximale Ausgangsleistung
Fréquence de fonctionnement / puissance de sortie maximale
Frequenza operativa / massima potenza di uscita
Frecuencia de funcionamiento / potencia de salida máxima
Рабочая частота / максимальная выходная мощность
WLAN
2400-2483.5 MHz / 20 dBm
5150-5250 MHz / 23 dBm
5250-5350 MHz / 20 dBm
5470-5725 MHz / 27 dBm
E-GSM-900 (except 4G kit) 900 MHz / 33 dBm ± 3 dB
DCS-1800 (except 4G kit) 1800 MHz 30 dBm ± 3 dB
WCDMA Band I (except 4G kit) 1922.4 MHz / 24 dBm ± 2.7 dB
WCDMA Band VIII (except 4G kit) 882.4 MHz / 24 dBm ± 2.7 dB
LTE Band 1 (except 4G kit) 2100 MHz / 23dBm ± 2.7 dB
LTE Band 3 1800 MHz / 23dBm ± 2.7 dB
LTE Band 7 2600 MHz / 23dBm ± 2.7 dB
LTE Band 8 (except 4G kit) 900 MHz / 23dBm ± 2.7 dB
LTE Band 20 800 MHz / 23dBm ± 2.7 dB
LTE Band 31 (only 4G kit) 450 MHz / 23dBm ± 2.7 dB
LTE Band 38 (except 4G kit) 2600 MHz / 23dBm ± 2.7 dB
LTE Band 40 (except 4G kit) 2300 MHz / 23dBm ± 2.7 dB
LTE Band 41 (only 4G kit) 2500 MHz / 23dBm ± 2.7 dB
LTE Band 42 (only 4G kit) 3500 MHz / 23dBm ± 2.7 dB
LTE Band 43 (only 4G kit) 3700 MHz / 23dBm ± 2.7 dB
Справжнім Mikrotikls SIA заявляє, що маршрутизатор відповідає основним вимогам та іншим відповідним положенням директиви 2014
/53/EC, а також суттєвим вимогам Технічного регламенту радіообладнання, затвердженого постановою Кабінету Міністрів України від
24 травня 2017 року № 355.
Для експлуатації в Україні необхідно отримати дозвіл на експлуатацію у порядку, затвердженому рішенням НКРЗІ від 01.11.2012 № 559,
зареєстрованому в Міністерстві юстиції України 03.01.2013 за № 57/22589.

This MikroTik device meets Maximum WLAN and LTE transmit power limits per ETSI regulations. For more detailed information see Declaration
of Conformity above / Dieses MikroTik-Gerät erfüllt die maximalen WLAN- und LTE-Sendeleistung Grenzwerte gemäß ETSI-Bestimmungen.
Weitere Informationen finden Sie oben unter Konformitätserklärung / Cet appareil MikroTik respecte les limites maximales de puissance de
transmission WLAN et LTE conformément aux réglementations ETSI. Pour plus d'informations, voir la déclaration de conformité ci-dessus /
Questo dispositivo MikroTik è conforme ai limiti massimi di potenza di trasmissione WLAN e LTE in conformità con le normative ETSI. Per
ulteriori informazioni, consultare la dichiarazione di conformità sopra / Este dispositivo MikroTik cumple con los límites máximos de potencia de
transmisión WLAN y LTE de acuerdo con las regulaciones ETSI. Para obtener más información, consulte la declaración de conformidad
anterior / Это устройство MikroTik соответствует максимальным пределам мощности передачи WLAN и LTE в соответствии с
правилами ETSI. Для получения дополнительной информации см. Декларацию соответствия выше.
The WLAN function for this device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency
range. / Die WLAN-Funktion dieses Geräts ist nur für die Verwendung in Innenräumen im Frequenzbereich 5150 bis 5350
MHz beschränkt. / La fonction WLAN de cet appareil est limitée à une utilisation en intérieur uniquement lorsqu'il fonctionne
dans la gamme de fréquences 5150 à 5350 MHz. / La funzione WLAN per questo dispositivo è limitata all'uso interno solo
quando si opera nella gamma di frequenza da 5150 a 5350 MHz. / La función WLAN para este dispositivo está restringida
al uso en interiores solo cuando se opera en el rango de frecuencia de 5150 a 5350 MHz. / Функция WLAN для этого
устройства ограничена использованием внутри помещения только при работе в диапазоне частот от 5150 до 5350 МГц.
The information contained here is subject to change. Please visit the product page on www.mikrotik.com for the most up to date version of this
document.