MiLAN MIL-S8000G User manual

8-Port Gigabit Switch
MIL-S8000G
User Guide
Eight Auto-negotiation 10/100/1000Mbps Gigabit Ethernet
RJ-45 Ports. Each port with Auto MDI/MDIX.

Regulatory Approval
- FCC Class A
- UL 1950
- CSA C22.2 Number 950
- EN60950
- CE
EN55022 Class A
EN55024
Canadian EMI Notice
This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le materiel
brouilleur du Canada.
European Notice
Products with the CE marking comply with both the EMC Directive (89/336EEC) and the Low Voltage
Directive (73/23EEC) issued by the commisions of the European Community. Compliance with these
directives implies conformity to the following European norms:
- EN55022 (CISPR 22) - Radio Frequency Interference
- EN61000-X - Electromagnetic Immunity
- EN60950 (IEC950) - Product Safety
Five-Year Limited Warranty
MiLAN Technology warrants to the original consumer or purchaser that each of its product and component thereof,
will be free from defects in material and/or workmanship for a period of five years from the original factory shipment
date. Any warranty hereunder is extended to the original consumer or purchaser and is not assignable.
MiLAN Technology makes no express or implied warranties including, but not limited to, any implied warranty of
merchantability or fitness for a particular purpose, except as expressly set forth in this warranty. In no event shall
MiLAN Technology be liable for incidental or consequential damages, costs, or expenses arising out of or in
connection with the performance of the product delivered hereunder. MiLAN Technology will in no case cover
damages arising out of the product being used in a negligent fashion or manner.
Trademarks
© 2003 MiLAN, the MiLAN logo and MiLAN Technology are either trademarks or registered
trademarks of MiLAN Technology in the United States and/or other countries.
To Contact MiLAN Technology
For prompt response when calling for service information, have the following information ready:
- Product serial number and revision
- Date of purchase
- Vendor or place of purchase
You can reach MiLAN Technology technical support at:
- E-mail: [e-mail]
- Telephone: [phone]
- Fax: [phone]
MiLAN Technology
1329 Moffett Park Drive
Sunnyvale, CA 94089
United States of America
Telephone: [phone]
Fax: [phone]
http://www.milan.com
[email protected]
P/N 90000404_A

1
Table of Contents
1. Introduction
Features
Package Contents
2. Hardware Description
Front Panel
LED Indicators
Rear Panel
3. Installation
Desktop Installation
Rack-mount Installation
Power On
4. Network Application
Backbone Switch
5. Network Configuration
Login to the Console Interface
5.1 Port Status
5.2 Port Configuration
5.3 Mirror Configuration
5.4 VLAN Configuration
5.5 VLAN Setup
5.6 Trunk Configuration
5.7 Miscellaneous Configuration
6. Troubleshooting
7. MIL-S8000G Technical Specifications

2
1. Introduction
Gigabit Ethernet over copper technology is a cost-effective way for
network equipment to be upgraded from Fast Ethernet to Gigabit speeds
without the use of expensive fiber optics cabling. Gigabit networks create
high-speed backbone connections between switches, servers, databases
and end stations.
The MIL-S8000G, an 8-Port Gigabit switch, is an ideal solution for solving
traffic block at the core of the network. It offers eight auto-negotiation
10/100/1000Base-T Gigabit Ethernet ports that can significantly improve
your network’s backbone performance. The switch will fit into any level
network to act as an exit to the backbone switch that can handle
throughput speeds up to 2000Mbps at Full-duplex mode.
Figure 1-1. MIL-S8000G
The switch will automatically detect the speed of the device that you plug
into it to allow connections to 10, 100 or 1000Mbps devices.
The eight port Gigabit switch features automatic MDI/MDIX connections
for each port. It also features store-and-forward switching and auto-
learning of source addresses with an 8,000 entry MAC address table.
Features
Conforms to IEEE 802.3, 802.3u, 802.3ab and 802.3x standards
Eight auto-negotiation 10/100/1000Base-TX switch ports (Using
shielded RJ-45 connections)
Automatic MDI/MDIX crossover for all ports
Embedded 8K entry MAC address table (Supports 8K
Unicast/Multicast/Broadcast addresses)
Store-and-Forward architecture
Full Duplex and Half Duplex flow control support
Plug-and-Play configuration
LED Indicators for Power, 100M, 1000M, LK/ACT, and FDX/COL
Standard 19-inch rackmount design
Console Management (Port Configuration/Statistics, Port Mirroring,
Port-Based VLAN’s and Port Trunking)

3
Package Contents
MIL-S8000G 8 port Gigabit switch
Power Cord
Four Adhesive Rubber Feet
User’s Manual
Warranty Card
Compare the contents of your MIL-S8000G package with the
standard checklist above. If any item is missing or damaged, please
contact your local dealer for service.

4
2. Hardware Description
Front Panel
The Front Panel of the 8-Port Gigabit Switch consists of eight auto-
negotiation 10/100/1000Mbps Ethernet RJ-45 connectors, supporting
automatic MDI/MDIX, and four LED-indicators (1000M, 100M, LK/ACT,
FUL/COL) for each Gigabit port.
Figure 2-1. The Front Panel of the 8-Port Gigabit Switch
RJ-45 Ports ( Auto MDI/MDIX ): Eight auto-negotiation
10/100/1000Mbps Ethernet RJ-45 connectors.
Console Port : Console management is available through the
Console Port. A direct connection between the Switch and an end
station ( PC ) via a RS-232 cable is required.
LED Indicators
The LED Indicators gives a real-time indication of system operating
statuses. There are four LED-indicators for each Gigabit port and one
Power LED for Unit. The following table provides descriptions of LEDs
status and their meaning.
Figure 2-2.
LED Indicators.
Console Port
LEDs
RJ-45 Gigabit Ports

5
LED Status Description
Green Power On
Power
Off Power is not connected
Green The port is operating at the speed of 1000Mbps.
1000M
Off No device attached or in 10/100Mbps mode
Green The port is operating at the speed of 100Mbps.
100M
Off No device attached or in 10Mbps mode
Green The port is connecting with the device.
Blinks The port is receiving or transmitting data.LK/ACT
Off No device attached.
Yellow The port is operating in Full Duplex mode.
FD
Off No device attached or in Half Duplex mode.
Table 2-1. Descriptions of LED Indicators
Rear Panel
The 3-pronged power plug and ventilation fan are located at the rear
panel. The switch will work with AC in the range 100-240V AC, 50-60Hz.
The rear panel of the MIL-S8000G Gigabit switch is shown below.
Figure 2-3. The Rear Panel of the MIL-S8000G Switch

6
3. Installation
Desktop Installation
Set the switch on a sufficiently large flat space with a power outlet nearby.
The surface should be clean, smooth, level, and sturdy.
Make sure there is enough clearance around the switch to allow
attachment of cables, power cord and air circulation.
Attaching Rubber Feet
A. Make sure mounting surface on the bottom of the switch is grease
and dust free.
B. Remove adhesive backing from the rubber feet.
Figure 3-1. Attaching rubber feet to each corner on the bottom of the
Switch
C. Apply the rubber feet to each corner on the bottom of the switch.
These footpads can prevent the switch from shock/vibration.
Rack-mounted Installation
The MIL-S8000G includes a rack-mounted kit that allows it to be mounted
in an EIA standard size, 19-inch Rack.
Perform the following steps to rack mount the switch:
A. Position one bracket to align with the holes on one side of the switch
and secure it with the smaller bracket screws. Then attach the
remaining bracket to the other side of the switch.

7
Figure 3-2. Attach mounting brackets with screws
B. After attaching both mounting brackets, position the MIL-S8000G
switch in the rack by lining up the holes in the brackets with the
appropriate holes on the rack. Secure the switch to the rack with a
screwdriver and the rack-mounting screws.
Figure 3-3. Mounting the MIL-S8000G in an EIA standard 19-inch Rack
Note: For proper ventilation, allow at least 4 inches (10 cm) of clearance
on the front and 3.4 inches (8 cm) on the back of the switch. This is
especially important for enclosed rack installation.
Power On
Connect the power cord to the power socket on the rear panel of the
switch. The other side of power cord connects to the power outlet. The
internal power supply in the Switch works with AC in the voltage range
100-240VAC, frequency 50~60Hz.
Check the power indicator on the front panel to see if power is properly
supplied.

8
4. Network Application
The MIL-S8000G Switch can be used connect servers, switches,
workstations, and PCs (a Gigabit 1000Base-T NIC is required for PC
installation) to each other by connecting these devices directly to the
Switch. The Switch automatically learns node addresses, which are used
to filter and forward all traffic, based on the destination address.
Backbone Switch
The MIL-S8000G Switch is an ideal solution for enterprise networks
where large data broadcasts are constantly processed.
All ports can be connected to departmental switches, and the
departmental switches can be connected to the MIL-S8000G Switch.
Each end station can access the server’s data by connecting the servers
to the core switch. This will allow all the devices in the network to
communicate with each other.

9
Workgroup A
Workgroup B
Figure 4-1. An example of a network connection, with the MIL-S8000G
Switch acting as the core switch.
This switch is an ideal solution for backbone connectivity. In the above
example, servers, department switches, and workstations are directly
connected to the core switch, the MIL-S8000G Switch.

10
5. Network Configuration
The Console port is a female DB-9 connector that enables a connection
to a PC or terminal for monitoring and configuring the MIL-S8000G
Switch. Use the supplied RS-232 cable with a male DB-9 connector to
connect a terminal or PC to the Console port.
The Console configuration allows the switch to be set to enable a user at
a remote console terminal to communicate with the MIL-S8000G Switch
as if the console terminal were directly connected to it.
Figure 5-1. Connecting the MIL-S8000G Switch to a terminal via RS-
232 cable.

11
Login to the Console Interface
When the connection between Switch and PC is finished, turn on the PC
and run a terminal emulation program or Hyper Terminal. Configure the
communication parameters to match the following default characteristics
of the console port:
Figure 5-2. The settings of communication parameters
5.1 Port Status
Figure 5-3. The screen of Port Status
View the statistics information displayed in this screen regarding a
specific port by entering the port number. Refresh or reset the counter as
necessary.
Baud Rate: 9600 bps
Data Bits: 8
Parity: none
Stop Bit: 1
Control flow: None

12
5.2 Port Configuration
Figure 5-4. The Port Configuration menu
Select each port to change the status, toggle the Enable / Disable field
and enter the appropriate value in the Flow Control field.

13
5.3 Mirror Configuration
Figure 5-5. The Device Configuration Setup menu
Figure 5-6. The Device Configuration Setup menu
By enabling port mirroring, the source port will be forwarded to the target
port. Select either Enable or Disable by using the <Backspace> key.

14
5.4 VLAN Configuration
Figure 5-7. The VLAN Configuration menu
Assigning physical ports within a work group is a simple and common
method of defining a virtual work group – VLAN. It delivers the benefit of
broadcast control and simplifies configuration for the network manager.
One advantage of the Port-Based VLAN is its simplicity and ease of
configuration. Limited security, however, is its drawback – anyone can
plug into the port and gain access to the VLAN.

15
5.5 VLAN Setup
Figure 5-8. The VLAN Setup menu
Select the VLAN entry to Enable or Disable the VLAN group. Use the
<Backspace> key to Enable (add) or Disable (remove) ports in the VLAN
group.
5.6 Trunk Configuration
Figure 5-9. The Trunk Configuration menu
Multiple links between switches can be grouped or trunked to work as
one virtual, aggregate link. Each trunk can hold up to 2 ports. Only ports
of the same speed can belong to a single trunk.

16
5.7 Miscellaneous Configuration
Figure 5-10. The Misc. Configuration menu
Select each port to change the status, toggle the Enable / Disable field
and enter the appropriate value in the Aging Time field.

17
6. Troubleshooting
This troubleshooting section is intended to help solve many common
problems that might occur when installing the MIL-S8000G. The switch
can be easily monitored through panel indicators to assist in identifying
problems.
Power
If the power indicator does not light up when the power cord is
plugged in, you may have a problem with the power outlet or power
cord. However, if the switch powers off after running for awhile,
check for loose power connections, power losses or surges at the
power outlet. If you still cannot resolve the problem, contact your
local dealer for assistance.
Diagnostic LED Indicator
1. If the link indicator does not light up after making a connection,
check whether the network interface (e.g., a network adapter
card on the attached device), network cable, or switch port is
defective or not.
2. Verify that the switch and attached device are powered on.
3. Be sure the cable is plugged into both the switch and the
corresponding device.
4. Verify that the proper cable type is used and its length does not
exceed specified limits (100 meters).
Transmission Mode
Verify that each port is set to the same transmission mode used by
the attached device, for example Half or Full-Duplex. The RJ-45
ports use auto-negotiation to set the transmission mode. If the
attached devices do not support auto-negotiation, the switch will
assume the port operates at half duplex.
Cabling
RJ-45 ports: Use unshielded twisted-pair (UTP) or shielded and
twisted pair (STP) cable for RJ-45 connections: 100Ω2-pair
UTP/STP Category 3, 4 or 5 cable for 10Mbps connections or 2-pair
UTP/STP 100ΩCategory 5 cable for 100Mbps connections and 4-
pair UTP/STP Category 5 cable for Gigabit 1000Mbps connections.
Also be sure that the length of any twisted-pair connection does not
exceed 100 meters (328 feet).

18
7. MIL-S8000G Technical
Specifications
Standards
Compliance
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
ANSI/IEEE 802.3 Auto-negotiation
Protocol CSMA/CD
Max Forwarding and
Max Filtering Rate
14,880 pps per Ethernet port
148,800 pps per Fast Ethernet port
1488,000 pps per Gigabit Ethernet port
LED Indicators Per Port:
100M, 1000M, LK/ACT, FD ( 4 LEDs )
Per Unit: Power
Copper Network
Cables
10Base-T: 2-pair UTP/STP Cat. 3, 4, 5 cable
EIA/TIA-568 100-ohm (100m )
100Base-TX: 2-pair UTP/STP Cat. 5 cable
EIA/TIA-568 100-ohm (100m )
1000Base-TX: 4-pair UTP/STP Cat. 5 cable
EIA/TIA-568 100-ohm (100m )
Dimensions 440mm x 224mm x 44mm
(w) 17.4" x (d) 8.8" x (h) 1.74"
Weight 2.9 Kg (6.4lbs)
Storage Temp. -40ºC to 70ºC (-40ºF to 158ºF)
Operational Temp. 0ºC to 45ºC ( 32ºF to 113ºF )
Operational Humidity 10% to 90% ( Non-condensing )
Internal Power 100-240V AC, 50-60Hz
Power Consumption 30 Watts ( Max )
EMI FCC Class A, CE Mark
Safety UL, cUL