Milestone MPM-66-IR-N User manual

MPM-66-IR-N
4K HDBaseT 6x6 Matrix Switcher
All Rights Reserved
Version: MPM-66-IR-N_2016V1.0
User Manual

4K HDBaseT 6x6 Matrix Switcher
Preface
Read this user manual carefully before using this product. Pictures shown in this manual
is for reference only, different model and specifications are subject to real product.
This manual is only for operation instruction only, not for any maintenance usage.
Trademarks
Product model and logo are trademarks. Any other trademarks mentioned in this manual
are acknowledged as the properties of the trademark owner. No part of this publication
may be copied or reproduced without prior written consent.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. It has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a commercial
installation.
Operation of this equipment in a residential area is likely to cause interference, in which
case the user at their own expense will be required to take whatever measures may be
necessary to correct the interference
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.

4K HDBaseT 6x6 Matrix Switcher
SAFETY PRECAUTIONS
To insure the best from the product, please read all instructions carefully before using
the device. Save this manual for further reference.
Unpack the equipment carefully and save the original box and packing material for
possible future shipment
Follow basic safety precautions to reduce the risk of fire, electrical shock and injury
to persons.
Do not dismantle the housing or modify the module. It may result in electrical shock
or burn.
Using supplies or parts not meeting the products’ specifications may cause damage,
deterioration or malfunction.
Refer all servicing to qualified service personnel.
To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this
product near water.
Do not put any heavy items on the extension cable in case of extrusion.
Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
Install the device in a place with fine ventilation to avoid damage caused by
overheat.
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If
an object or liquid falls or spills on to the housing, unplug the module immediately.
Do not twist or pull by force ends of the optical cable. It can cause malfunction.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning.
Unplug the power cord when left unused for a long period of time.
Information on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as normal electrical wastes.

4K HDBaseT 6x6 Matrix Switcher
Contents
1. Introduction.................................................................................................................1
1.1 Introduction to the MPM-66-IR-N.......................................................................1
1.2 Features ............................................................................................................1
1.3 Package List......................................................................................................1
2. Product Appearance of the MPM-66-IR-N ..................................................................2
2.1 Front Panel........................................................................................................2
2.2 Rear Panel.........................................................................................................3
3. System Connection.....................................................................................................4
3.1 System Applications ..........................................................................................4
3.2 Usage Precautions............................................................................................4
3.3 Connection Diagram..........................................................................................5
3.4 Connection Procedure.......................................................................................5
3.5 Connection with HDBT Receiver .......................................................................6
4. System Operations .....................................................................................................7
4.1 Front Panel Button Control................................................................................7
4.1.1 Switching I/O connection.........................................................................7
4.1.2 EDID Management..................................................................................7
4.1.3 Inquiry......................................................................................................9
4.1.4 Clear operation........................................................................................9
4.2 IR Control ........................................................................................................10
4.2.1 Usage of IR Remote..............................................................................10
4.2.2 Control Far-end Device locally...............................................................11
4.2.3 Control Local Device Remotely .............................................................12
4.3 RS232 Control.................................................................................................14
4.3.1 Connection with RS232 Communication Port........................................14
4.3.2 Control through 9-pin RS232 port..........................................................15
4.3.3 Control through 3-pin RS232 port..........................................................16
4.3.4 Installation/uninstallation of RS232 Control Software............................17
4.3.5 Basic Settings........................................................................................17
4.3.6 RS232 Communication Commands ......................................................18
4.4 TCP/IP Control.................................................................................................25

4K HDBaseT 6x6 Matrix Switcher
4.4.1 Control Modes.......................................................................................25
4.4.2 Control via TCP/IP communication software .........................................26
4.4.3 GUI for TCP/IP control...........................................................................27
4.4.4 Port Management..................................................................................30
4.5 Firmware Update via USB...............................................................................31
5. Specification .............................................................................................................32
6. Panel Drawing ..........................................................................................................33
7. Troubleshooting & Maintenance ...............................................................................34
8. After-sales Service....................................................................................................36

4K HDBaseT 6x6 Matrix Switcher
1
1. Introduction
1.1 Introduction to the MPM-66-IR-N
MPM-66-IR-N is a professional 6x6 HDBaseT Matrix Switcher that accommodates 6
HDMI IN (HDMI1.4 & HDCP2.2 compliant) & 6 IR IN.
Select HDMI input by front panel buttons, IR, RS232, or GUI. The selected source is
delivered to HDMI Output 1~3 (switched synchronously with HDBaseT output 1~3) &
HDBaseT outputs 1~6 (easy extension to 70m at 1080p and 40m at 4Kx2K on a single
CAT5e/6 connection with HDBaseT receivers, with PoC).
It also features EDID management.
1.2 Features
6 HDMI Input support HDMI 1.4 &HDCP2.2, and compliant with lower standards,
capable to transmit 4Kx2K@60Hz & 1080p 3D
Support manual input HDCP auto-detecting and output manual HDCP management
3 HDMI Output support HDMI1.4& HDCP1.4, transmit 4Kx2K signal for 8m
6 HDBaseT outputs for easy extension to 70m at 1080p and 40m at 4Kx2K over
single CAT5e/6 cable, support PoC
LCD screen shows real-time I/O connection status, switching status, HDCP status,
and output resolution.
Controllable via front panel, TCP/IP, and bi-directional IR& RS232
Built-in GUI for TCP/IP control
Powerful EDID management
Support off memory for reliable operation
Convenient firmware upgrade through Micro USB port
Easy installation with rack-mounting design
1.3 Package List
1 x MPM-66-IR-N
2 x Mounting ears (6 x Screws)
1 x RS232 cable
1 x IR Receiver (5V, with carrier)
4 x Rubber Feet (4 x Screws)
1 x IR remote
1 x Power cord
12 x Pluggable Terminal Blocks
1 x User manual
Confirm if the product and the accessories are all included, if not, please contact
with the dealers.

4K HDBaseT 6x6 Matrix Switcher
2
2. Product Appearance of the MPM-66-IR-N
2.1 Front Panel
No.
Name
Description
①
Firmware
Micro USB port for firmware updating
②
Power
Indicator
Illuminate red when power on; light yellow in standby mode
③
IR
In-built IR sensor, receive IR signals sent from IR remote.
④
LCD Screen
Display real-time operation status.
⑤
INPUTS/
Menu
buttons
Normal mode: input selection buttons ranging from 1~6.
Inquiry mode (buttons 1~4): Press “ENTER” for more than 3
seconds to enter this mode. Dial to select different
menus, to select different options.
⑥
OUTPUTS
buttons/
EDID
Management
buttons
Normal mode: output selection buttons ranging from 1~6
EDID Invoking mode: press and hold EDID button for 3
seconds or more to enter this mode, buttons 1~6 correspond
to the 6 embedded EDID data separately. Press any of the 6
buttons to invoke embedded EDID data.
⑦
Function
buttons
ALL: Select all inputs/ outputs
EDID: EDID management button
CLEAR: Withdraw an operation before it comes into effect
ENTER:
Confirm operation
Press for 3 seconds to enter in Inquiry mode.
SYS TEM MONITOR
MENU
FIRMWARE
CLEAR ENTER
ALL EDID
1 2 4 563
INPUTS
OUTPUTS
MPM-66-IR-N

4K HDBaseT 6x6 Matrix Switcher
3
2.2 Rear Panel
No.
Name
Description
①
INPUTS
a. IR OUT: connect with IR emmitters, making up an IR
matrix with the IR IN sockets on the far-end receivers. IR
signal can be switched synchronously with the AV signal,
or separately.
In default setting, the 6 IR OUT corresponds with the 6 IR
IN throughly, i.e. IR OUT1→IR IN1,…IR OUT6→IR IN6.
b. HDMI: HDMI input ports, connect with HDMI sources.
②
OUTPUTS
c. IR IN: Connect with IR receiver (with carrier), work with IR
OUT on the corresponding far-end receiver, cannot be
switched separately.
d. RS232: serial control ports, support bi-directional control
with RS232 port on corresponding HDBT receiver(such
as MPTP-T70R), cannot be switched separately.
e. AUDIO: stereo audio output ports, output de-embeded
HDMI audio
f. HDMI: Local HDMI output ports, synchronously switched
with HDBaseT Output 1~3
g. HDBaseT: work with HDBaseT receivers to extend
signals and energize far-end HDBaseT receiver on a
single CAT5e/6 cable.
③
RS232
Serial control port, connect with control device such as a PC.
④
IR Control
IR ALL IN: connect with IR receiver, delivers the received IR
signal to all the 6 far-end receivers.
RS232
TCP/IP
IR AL L IN
IR EY E
LR
HDBaseT
RS232 AUDIO
OUT PUT 1
Tx Rx
HDMI
1
LR
HDBaseT
RS232 AUDIO
OUT PUT 2
Tx Rx
HDMI
2
LR
HDBaseT
RS232 AUDIO
OUT PUT 3
Tx Rx
HDMI
3
LR
HDBaseT
RS232 AUDIO
OUT PUT 4
Tx Rx
4
LR
HDBaseT
RS232 AUDIO
OUT PUT 5
Tx Rx
5
LR
HDBaseT
RS232 AUDIO
OUT PUT 6
Tx Rx
6
IR INIR INIR INIR INIR INIR IN
HDM I 6 HDM I 5
5IR OU T
INPUT
6
HDM I 4 HDM I 3
3IR OUT
INPUT
4
HDM I 2 HDM I 1
1
IR OU T
INPUT
2
Matrix
4K
HDCP2.2
RS232
TCP/IP
IR ALL IN
IR EYE
HDMI 2 HDMI 1
1
IR OUT
INPUT
2
LR
HDBaseT
RS232 AUDIO
OUTPUT 1
Tx Rx
HDMI
1
IR IN

4K HDBaseT 6x6 Matrix Switcher
4
IR EYE: Connect with extended IR receiver, use the IR remote
to control the MPM-66-IR-N.
⑤
TCP/IP
TCP/IP port for unit control
⑥
GROUND
Connect to grounding
⑦
Power
Power Trigger: Press the button to power on/off the matrix.
The indicator turns red when power on.
Power port: Insert AC 100V~240V power adapter here
Note: Pictures shown in this manual are for reference only, different model and
specifications are subject to real product.
3. System Connection
3.1 System Applications
As its good performance in control and transmission, the MPM-66-IR-N can be widely
used in computer realm, monitoring, large screen displaying, conference system,
television education and bank securities institutions etc.
3.2 Usage Precautions
1) System should be installed in a clean environment and has a prop temperature and
humidity.
2) All of the power switches, plugs, sockets and power cords should be insulated and
safe.
3) All devices should be connected before power on.

4K HDBaseT 6x6 Matrix Switcher
5
3.3 Connection Diagram
3.4 Connection Procedure
1) Connect HDMI sources (e.g. DVD) to HDMI inputs of the MPM-66-IR-N with HDMI
cables.
2) Connect HDBaseT receivers (e.g. MPTP-T70R) to the HDBaseT Outputs with
straight-through CAT5e/6.
3) Connect HDMI displays (e.g. HDTV) to HDMI outputs of the MPM-66-IR-N with
HDMI cables.
4) Connect speakers/earphones to AUDIO output ports
5) Connect control device (e.g. a PC) to the RS232 port of either MPM-66-IR-N or
far-end receivers. RS232 signal can be transmitted bi-directionally between
MPM-66-IR-N and far-end receivers.
6) MPM-66-IR-N can collect IR signal sent by the included IR remote via its built-in IR
sensor or through external IR receiver connected to the IR IN/ IR EYE/ IR ALL IN
port. The IR signal can be transmitted bi-directionally between MPM-66-IR-N and
far-end receivers.
7) Insert AC 100V~240V power outlet to power port of MPM-66-IR-N and switch on the
power trigger.
MPTP-T70R
MPM66IRN
---
VCR
DVD
Laptop
HDTV PoC
Speaker
IR Transmitter
RS232 Control Panel