Miller GP30 User manual

1242 ARIZONA AVE.
LARCHWOOD, IA 51241
1-800-570-8205
GP30 LOADER
PARTS and INSTRUCTIONS
OWNER’S MANUAL

TO PREVENT POSSIBLE ROLLOVER, OBSERVE THE FOLLOWING
SAFETY PRECAUTIONS
♦ Carry loads as low as possible
♦ Drive tractor slowly when turning, operating on hills or inclines, or traversing un-
even ground
♦ Raise load to full height only when tractor in on even ground and front wheels
are straight ahead
TO PREVENT POSSIBLE PERSONAL INJURY, OBSERVE THE FOLLOW-
ING SAFETY PRECAUTIONS
♦ Never walk or work under a raised loader that is not firmly supported
♦ Always relieve the hydraulic system to zero pressure before performing repairs on
any component of the loader’s hydraulic system
DANGER

TABLE OF CONTENTS
• Composite Bearing Information
• Mounting Loader on Tractor
• Dismounting Loader
• Quick-attach Instructions
• Parts Schematics
• Cylinder Packing Detail
• Loader Specifications
• Warranty
SERIAL No. of Loader Purchased _______________________
Date Purchased____________________

COMPOSITE BEARING INFORMATION
FIGURE A. Your GP/GL-Series loader is equipped
with composite, greaseless bearings at all (12) pivot
points. These high-quality bearings should not be
confused with plastic bushings, sintered bushings, or
metal-backed bearings. Composite bearings are
made from an ultra-strong fiberglass composite that
has twice the compressive yield strength of plain
carbon steel. Their greaseless feature is due to a
Teflon-impregnated liner that is interwoven to the
bearing’s inside diameter. The bearings are de-
signed to last the life of the loader and the pins that
rotate in the bearings should exhibit practically no
wear.
FIG. A FIG. B
Pin Seal
Pin Seal
Bearing
FIGURE B. Even though the composite bearings on
your GP/GL-Series loader have excellent resistance to
dirt particles, the (4) pivot points on the bucket have
an added feature. The two lower bucket cylinder piv-
ots and the two mainframe-to-bucket pivots are
equipped with pin seals on each end of the bearing
housing. It is these four pivot points that are usually
down in the dirt and grime, but with a GP/GL-Series
loader, you won’t have to worry about pin failures
again!
Bearing
Housing
FIGURE C. Should any of your bearings have to be re-
moved, this photo shows the tool that is available to remove
and install the bearings properly. They are available for pur-
chase, you just need to tell your dealer or Miller Loaders the
model of loader you have. If you’d prefer to make your own,
here are a few things to remember:
• The nose should be 1/4” longer than the bearing
• A 1/4” bevel on the end of the nose
• The shoulder must be just slightly smaller than the out-
side diameter of the bearing
• The diameter of the nose should be about 0.005 less
than the inside diameter of the bearing
FIG. C
Bevel
Nose Shoulder

MOUNTING LOADER
STEP 1 For a new loader installation, the mountings must be installed on the tractor first. Refer to the typical
mounting kit shown in Figure 1. A detailed schematic of your specific kit is available—just call 1-800-570-8205 if the
schematic was not included with your new loader.
STEP 2 The loader should have been dismounted (or assembled) on flat, level ground (see Figure 2).
FIG. 1
STEP 3 Approach the loader as shown in Figure 3 and connect the hydraulics.
STEP 4 Once the hydraulics are functional, begin to slowly tip the bucket forward from its flat position, see Figure
4A. This will bring the upright masts of the loader towards the support shafts on the mountings (Fig. 4B). Figure 4C
shows the mast completely seated on the support shaft. Once the mast is resting on the support shaft, the V-block
will also be aligned with the tapered guide block. The lift cylinders can be used to rotate the upright mast and firmly
seat the V-block against the guide block.
FIG. 2
FIG. 4A
FIG. 3
Support shaft
Upright mast
FIG. 4B
Tapered
Guide Block
V-Block
FIG. 4C
STEP 5 Using a 1-1/2” socket or end wrench, install and tighten the 1” retaining bolt that secures the V-block to
the guide block. See Figure 5.
STEP 6 Raise the bucket off the ground so that the stand legs are hanging free. See Figure 6.
Stand Legs Stand Legs Stored
FIG. 5 FIG. 6
FIG. 7
STEP 7 Return the stand legs to their stored position. See Figure 7.

DISMOUNTING LOADER
STEP 1 DRIVE THE TRACTOR ONTO FLAT CONCRETE and place the loader in the position shown in Fig 1.
STEP 2 Remove the stand legs from their stored position and place them in their dismount position. Slide the in-
ner tubes down to the extended position and secure them with the 3/4” pins. See Fig. 2.
FIG. 1
STEP 3 Gently lower the loader until the stand legs touch the ground. Please note that the stand legs are not de-
signed to withstand all of the down-force that can be generated with the lift cylinders, they are designed to support
the weight of the loader only. Rotate the bucket so that the cutting edge and stand legs are all resting on the
ground. See Fig. 3.
FIG. 4
STEP 4,5 Using a 1-1/2” socket or end wrench, remove the 1” retaining bolt that secures the V-block to the guide
block. See Figures 4,5.
STEP 6 Using the bucket cylinders, slowly flatten the bucket. This will start to lift the upright mast out of the pillar
mount, see Figure 6A. When the bucket is completely flat on the ground, the upright mast will be high enough to
back away from the loader. See Figure 6B
FIG. 5
FIG. 6A
STEP 7 Disconnect the hydraulic supply to the loader and slowly back away from the loader. See Figure 7.
FIG. 3
FIG. 2 Stand Legs
FIG. 7
FIG. 6B
Upright Mast
Pillar Mount

QUICK-ATTACH INSTRUCTIONS
UNCOUPLING
1. Raise sliding latches as shown in Figure 1.
2. Rotate QT pins out of the lower notches, raise, and then rotate them into the upper notches
of the sliding latches as shown in Figure 2.
3. Slide the sliding latches down as shown in Figure 3. This secures the QT pins in the “up”
position so they do not interfere when hooking up to the next attachment.
COUPLING
1. Approach and hook onto the attachment with QT pins secured in the “up” position as shown
in Figure 3.
2. When the QT frame is flat against the attachment, raise the sliding latches as shown in Fig-
ure 2.
3. Rotate QT pins out of the upper notches, lower, and then rotate them into the lower notches
on the sliding latches as shown in Figure 1. NOTE: If the QT pins do not easily slide thru the
lug on the attachment, do not force them. Simply rotate the attachment back and forth
slowly with the bucket cylinders of the loader and the QT pins should fall into place. Periodi-
cally grease the QT pins and sliding latches.
4. Secure the QT pins in the “down” position by sliding the latches down.

1
8
15
19
29
10
15 19
16
14 17
30
36
27
28
13
12
35
3
26
18
2
11
9
31
32
29
34
33
29
ITEM
NO. PART NUMBER DESCRIPTION QTY.
1 MF30 MAINFRAME, GL30/GP30 1
2 QT30 QUICK ATTACH FRAME 1
3CY-059 CYLINDER, BUCKET, GL/GP30 2
8 PN-600AC16 PIN, CHROME 2" x 6" WITH RETAINER 2
9 PN-700AC16 PIN, CHROME 2" x 7" WITH RETAINER 2
10 PN-650AC12 PIN, CHROME 1-1/2 x 6-1/2 WITH RETAINER 2
11 PN-725AC12 PIN, CHROME 1-1/2 x 7-1/4 WITH RETAINER 2
12 PN-11B12 REAR BUCKET CYLINDER PIN 2
13 PN-4750-J12 LIFT CYLINDER PIN, 1-1/2 CHROME 2
14 HW-LS-16-A LOCKWASHER, 1-IN., MED ZN 2
15 HW-LS-08-A LOCKWASHER, 1/2, MED ZN 10
16 HW-NS-16-B NUT, 1-14 UNF, GR5, NZ 2
17 HW-NS-16-E NUT, 1-14 UNF GR8 TL, ZN 2
18 HW-NS-10-A NUT, 5/8-11 UNC GR8, ZN 1
19 HW-NS-08-A NUT, 1/2-13 UNC, ZN 10
26 LV01-04 SLIDE ROD ASSY, LEVEL INDICATOR 1
27 LV30-01 SLIDE TUBE ASSY, LEVEL INDICATOR 1
28 LV30-03 LEVEL INDICATOR ROD, GL/GP30 1
29 HW-BS-08-0200-A BOLT, 1/2-13 UNC, GR5 ZN, 2" LONG 8
30 HW-BS-10-0100-A BOLT, 5/8-11 UNC, GR5 ZN, 1" LONG 1
31 HW-BS-08-0150-A BOLT, 1/2-13 UNC, GR5 ZN, 1-1/2" LONG 1
32 HW-WS-08-A WASHER, 1/2" FLAT, ZN 3
33 UP30-AR UPRIGHT LEG, RIGHT 1
34 UP30-AL UPRIGHT LEG, LEFT 1
35 CY-060-L CYLINDER, GP30 LIFT (LH) 1
36 CY-060-R CYLINDER, GP30 LIFT (RH) 1
DWG. NO.
SHEET
REV.
DATE
GP30 LOADER
OF
1
A
1/13/2005
GP30
1
SCHEMATIC
WEIGHT: 2061.843
GENERAL PART LIST

ITEM NO. PART NUMBER DESCRIPTION with bearings/QTY.
20 BR-2500K-3750 COMPOSITE BEARING, 2.00 BORE, 3.75 LONG 2
21 PS-2000-45 Pin Seal (MRW), 2.0 ID x 2.5 OD x 5/16 Thick 8
22 BR-2000K-1500 COMPOSITE BEARING, 1.50 BORE, 1.50 LONG 2
23 BR-2500K-3125 COMPOSITE BEARING, 2.00 BORE, 3.125 LONG 2
1159.886
DWG. NO.
SHEET
REV.
DATE
MAINFRAME, GL30/GP30
OF
1
A
1/28/2005
MF30
1
SCHEMATIC
WEIGHT:
BEARING & SEAL DETAIL
21
23
23
22
20
21 20
21
21
22
21
21
21
21

ITEM
NO. PART NUMBER DESCRIPTION Pin Up Latch Up/QTY.
1 QT02-01L SLIDING LATCH ASSY, QT, LH 1
2 QT02-01R SLIDING LATCH ASSY, QT, RH 1
3 QT02-14 RETAINING PIN ASSEMBLY, QT 2
4 QT30-W WELDED QT FRAME 1
ITEM
NO. PART NUMBER DESCRIPTION QTY.
4 HW-NS-06-A NUT, 3/8-16 UNC, CL, ZN 4
5 HW-SP-01 SPRING, QT HANDLE 4
6 HW-WS-06-A WASHER, 3/8, FLAT, ZN 4
DWG. NO.
SHEET
REV.
DATE
QUICK ATTACH FRAME
OF
1
A
1/13/2005
QT30
1
SCHEMATIC
WEIGHT: 246.509
GL30/GP30/GP35
4
1
3
2
3
564
564
465
465
SLIDING LATCH DETAIL
12

DWG. NO.
SHEET
REV.
DATE
GL30/GP30
HOSES & PIPING
OF
1
A
1/13/2005
HP30
1
SCHEMATIC
WEIGHT: 23.706
ITEM
NO. PART NUMBER DESCRIPTION with pipes/QTY.
1HP30P-BL BUCKET TILT FEEDLINE, LOWER 1
2HP30P-BU BUCKET TILT FEEDLINE, UPPER 1
3HP30P-LL LIFT FEEDLINE, LOWER 1
4HP30P-LU LIFT FEEDLINE, UPPER 1
5PC06X2 PIPE CLAMP 7
6HP30-HBL BUCKET CYLINDER HOSE, LONG (45.5") 2
7HP30-HBS BUCKET CYLINDER HOSE, SHORT (41") 2
8HP30-HLL LIFT CYLINDER HOSE, LONG (35") 2
9HP30-HLS LIFT CYLINDER HOSE, SHORT (24") 2
10 HW-LS-05-A LOCKWASHER, 5/16, ZN 7
11 HW-BS-05-0125-A BOLT, 5/16-18 UNC, GR5 ZN, 1-1/4" LONG 7
8
9
6
7
7
6
9
11
4
3
2
1
5
10
8
INSIDE DIAMETER 1/2"
WORKING PRESSURE 3000 PSI
90 DEGREE END -10FJX90
STRAIGHT END -08FJX
HOSE SPECIFICATIONS

ITEM
NO. PART NUMBER DESCRIPTION with aux kit/QTY.
24 HP30P-GU AUXILLARY FEEDLINE, UPPER 1
25 HP30P-GL AUXILLARY FEEDLINE, LOWER 1
26 SF-2706-LN-10-08 BULKHEAD CONNECTOR, -10 JIC to 1/2 NPT 2
27 PC06X2 PIPE CLAMP 9
28 HW-BS-05-0100-A BOLT, 5/16-18 UNC, GR5 ZN, 1" LONG 9
29 HW-LS-05-A LOCKWASHER, 5/16, ZN 9
30 HOSE SPECIFY LENGTH REQUIRED 2
31 HA-TP-4050-3 TIP, FEMALE 3/8 NPT (PIONEER 4050-3) 1
32 HA-TP-4010-3 TIP, MALE 3/8 NPT (PIONEER 4010-3) 1
33 SF-5405-06-08 EXPANDING PIPE ADAPTER, 3/8 to 1/2 NPT 2
DWG. NO.
SHEET
REV.
DATE
GL/GP30 LOADER
AUX. LINE KIT
OF
1
A
1/13/2005
AU30
1
SCHEMATIC
WEIGHT: 9.0
31 32
26 26
27 29
28
24
25
30
30
33
33

3
2
1
7
8
6
7
5
4
9
7
8
76
ITEM
NO. PART NUMBER DESCRIPTION Stand Legs/QTY.
1 SL30-TL TOP TUBE ASSY, LEFT 1
2 SL30-BL BOTTOM TUBE ASSY, STAND LEG (LH) 1
3 SL30-HL STAND LEG HANDLE, LEFT 1
4 SL30-TR TOP TUBE ASSY, RIGHT 1
5 SL30-BR BOTTOM TUBE ASSY, STAND LEG (RH) 1
6 PIN1-006 CLEVIS PIN, 3/4 X 3 1/2 ZNC 2
7 PIN1-017 HAIRPIN COTTER, 2-11/16 LONG 6
8 HW-NS-16-E NUT, 1-14 UNF GR8 TL, ZN 2
9 SL30-HR STAND LEG HANDLE, RIGHT 1
DWG. NO.
SHEET
REV.
DATE OF
1
A
1/13/2005
SL30H
1
SCHEMATIC
WEIGHT: 85.345
GL30/GP30 LOADER
STAND LEG PART LIST

ITEM NO. PART NUMBER DESCRIPTION QTY.
1 CY-059T TUBE ASSEMBLY, GP/GL25-30 BUCKET 1
2 CY-059D ROD ASSY, GL/GP30 BUCKET 1
3 CP-GL-3017-S GLAND, 3017, SHORT-TAIL 1
4 CP-PS-3017-U PISTON, 3017 U-CUP 1
5 HW-NS-16-A NUT, 1-14 UNF, TOP LOCK, PLAIN 1
6 CP-KT-3017-U P-KIT, 3.000 X 1.750 UC 1
7 PS-1500-45 Pin Seal (MRW), 1.50 ID x 2.0 OD x 5/16 Thick 4
8 BR-2000K-3750 COMPOSITE BEARING, 1.50 BORE, 3.75 LONG 1
9 BR-2000K-3125 COMPOSITE BEARING, 1.50 BORE, 3.125 LONG 1
1
54
2
3
9
78
7
NOTES:
1. BEARINGS AND SEALS ARE SOLD SEPARATELY.
2. PACKING KIT SHOWN IN PART LIST, BUT NOT SHOWN IN DRAWING.
SEE NOTE 1.
SEE NOTE 1.
SEE NOTE 1.
SEE NOTE 1.
7
7
25 1/4"
28 3/8"
DWG. NO.
SHEET
DATE
CYLINDER, GL/GP30 BUCKET
OF
1
1/28/2005
CY-059
1
SCHEMATIC
ALL DIMENSIONS IN INCHES
49.822
BORE
ROD
STROKE
PORT STYLE
WEIGHT: LBS.
3.000
1.750
20-5/8"
-08 JIC
CY-059
CYLINDER, GL/GP30 BUCKET

3
4
2
5
1
7
NOTES:
1. BEARING AND SEALS SOLD SEPARATELY.
2. PACKING KIT SHOWN IN PART LIST, BUT NOT SHOWN IN DRAWING.
3. EARLY CYLINDERS (12/04-2/05) WERE 1" SHORTER AND HAD 1" LESS STROKE.
SEE NOTE 1
8
8
DWG. NO.
SHEET
DATE
LIFT CYLINDER, GP30, LH
OF
1
1/28/2005
CY-060-L
1
SCHEMATIC
ALL DIMENSIONS IN INCHES
85.856
BORE
ROD
STROKE
PORT STYLE
WEIGHT: LBS.
3.500
2.000
33-1/4"
-08 JIC
CY-060-L
LIFT CYLINDER, GP30, LH
46 7/8"
39 1/8" SEE NOTE 3. ITEM NO. PART NUMBER DESCRIPTION QTY.
1 CY-058D ROD ASSEMBLY, GL/GP30 LIFT 1
2 HW-NS-16-A NUT, 1-14 UNF, TOP LOCK, PLAIN 1
3 CY-060-LT TUBE ASSEMBLY, GP30 LIFT, LH 1
4 CP-GL-3520-L GLAND, 3520 LONG-TAIL 1
5 CP-PS-3520-U PISTON, 3520 U-CUP 1
6 CP-KT-3520-U P-KIT, 3.500 X 2.000 UC 1
7 BR-2000K-3125 COMPOSITE BEARING, 1.50 BORE, 3.125 LONG 1
8 PS-1500-45 Pin Seal (MRW), 1.50 ID x 2.0 OD x 5/16 Thick 2

ITEM NO. PART NUMBER DESCRIPTION QTY.
1 CY-058D ROD ASSEMBLY, GL/GP30 LIFT 1
2 HW-NS-16-A NUT, 1-14 UNF, TOP LOCK, PLAIN 1
3 CY-060-RT TUBE ASSEMBLY, GP30 LIFT, RH 1
4 CP-GL-3520-L GLAND, 3520 LONG-TAIL 1
5 CP-PS-3520-U PISTON, 3520 U-CUP 1
6 CP-KT-3520-U P-KIT, 3.500 X 2.000 UC 1
7 BR-2000K-3125 COMPOSITE BEARING, 1.50 BORE, 3.125 LONG 1
8 PS-1500-45 Pin Seal (MRW), 1.50 ID x 2.0 OD x 5/16 Thick 2
46 7/8"
39 1/8" SEE NOTE 3.
DWG. NO.
SHEET
DATE
LIFT CYLINDER, GP30, RH
OF
1
1/28/2005
CY-060-R
1
SCHEMATIC
ALL DIMENSIONS IN INCHES
85.856
BORE
ROD
STROKE
PORT STYLE
WEIGHT: LBS.
3.500
2.000
33-3/4"
-08 JIC
CY-060-R
LIFT CYLINDER, GP30, RH
3
4
2
5
1
7
NOTES:
1. BEARING AND SEALS SOLD SEPARATELY FROM COMPLETE CYLINDER.
2. PACKING KIT SHOWN IN PART LIST, BUT NOT SHOWN IN DRAWING.
3. EARLY CYLINDERS (12/04-2/05) WERE 1" SHORTER AND HAD 1" LESS STROKE.
SEE NOTE 1
8
8

ROD WIPER
PISTON GLAND
SEAL, U-CUP, LARGE
SEAL, U-CUP, SMALL
O-RING, SMALL
O-RING, LARGE B/U WASHER
SNAP RING
SCHEMATIC
DWG. NO.
SHEET
REV.
DATE
PACKING CONFIGURATION, U-CUP
OF
1
A
1/13/2005
CP-KT-U
1
WEIGHT:
FRONT OF CYLINDER

14’−8"
13’−6"
2’−11"
34°
44°
11’−10"
8"
100" TYPICAL
GP30 SPECIFICATIONS
SPECIFICATIONS AND PERFORMANCE NUMBERS ARE FOR REFERENCE ONLY
WEIGHTS:
Loader (less bucket and mounts) : 2090 lbs.
8 FT Bucket : 800 lbs.
Mounting Kit (Typical) : 710 lbs.
Total : 3600 lbs.
LIFTING CAPACITY:
Breakaway Lift : 7400 lbs.
Full Height Lift : 6000 lbs.
With load 800mm (31.5”) ahead of bucket pivot
And 2850 psi pressure at lift cylinders

WARRANTY Dec 2004
ALL PRODUCTS MANUFACTURED BY MILLER LOADERS, INCOPRORATED (MLI) EXCEPT THE
CHROME-PLATED PIVOT PINS USED ON GREASELESS LOADERS, ARE GUARENTEED TO THE
ORIGINAL PURCHASER FOR A PERIOD OF ONE YEAR FROM THE DAY OF PURCHASE AGAINST ANY
DEFECTS IN MATERIALS AND WORKMANSHIP OF FARM LOADERS AND ATTACHMENTS THAT ARE
USED IN NORMAL FARM OPERATIONS. THE CHROME-PLATED PIVOT PINS USED ON GREASELESS
LOADERS ARE GUARENTEED TO THE ORIGINAL PURCHASER FOR A PERIOD OF FIVE YEARS FROM
THE DAY OF PURCHASE AGAINST ANY DEFECTS IN MATERIALS AND WORKMANSHIP OR AGAINST
WEAR THROUGH OF THE CHROME FINISH COVERING AT LEAST ONE-QUARTER OF THE PIN
SURFACE.
ALL GREASELESS COMPOSITE BEARINGS SOLD BUT NOT MANUFACTURED BY MLI ARE
GUARENTEED TO THE ORIGINAL PURCHASER FOR A PERIOD OF FIVE YEARS FROM THE DAY OF
PURCHASE AGAINST BREAKAGE OR LOSS OF THEIR SELF-LUBRICATING PROPERTY.
THE FIVE YEAR WARRANTY FOR THE CHROME-PLATED PIVOT PINS AND GREASELESS COMPOSITE
BEARINGS IS LIMITED TO THE PARTS ONLY. MLI IS NOT RESPONSIBLE FOR ANY LABOR NECESSARY
FOR THE INSPECTION, REMOVAL, OR REPLACEMENT OF SAID PIVOT PINS AND/OR COMPOSITE
BEARINGS.
ALL PARTS SOLD BUT NOT MANUFACTURED BY MLI THAT INCLUDE BUT ARE NOT LIMITED TO
ZINC-PLATED PINS, HOSES, VALVES, QUICK COUPLERS, PUMPS, TANKS, ETC. ARE COVERED ONLY
TO THE EXTENT OF THE MANUFACTURE’S WARRANTY ON THESE ITEMS. MLI DOES NOT
WARRANTY THESE ITEMS EXPRESSLY OR IMPLIEDLY.
DEFACEMENT OF ANY PART BY WELDING OR OTHERWISE ALTERING, OR EXCESSIVE WEAR ON PINS
CAUSED BY LACK OF LUBRICATION, NULLIFIES THE WARRANTY ON THE MLI PRODUCT.
MLI ASSUMES NO RESPONSIBILITY AS TO THE PERFORMANCE OR FAILURE OF A TRACTOR’S
HYDRAULIC SYSTEM.
THE HYDRAULIC COMPONENTS OF THE MLI PRODUCTS ARE GUARENTEED UP TO A PRESSURE OF
3000 POUNDS PER SQUARE INCH AT A MAXIMUM FLOW RATE OF 30 GALLONS PER MINUTE.
MLI ASSUMES NO RESPONSIBILITY FOR THE FAILURE OF THE PURCHASER TO SECURE THE LOADER
TO THE TRACTOR PROPER, WHICH INCLUDES PROPER BOLT TIGHTENING AND SECURING OF ALL
CONNECTION POINTS.
ALL ITEMS MANUFACTURED BY MLI REQUIRING WARRANTY CONSIDERATION MUST BE RETURNED
TO MLI OR A DESIGNATED REPRESENTATIVE BY THE ORIGINAL PURCHASER. ANY ITEM SO
RETURNED BY COMMON CARRIER MUST BE PREPAID FREIGHT.
THE WARRANTIES PROVIDED BY MLI AS REFERRED TO ABOVE SHALL BE THE SOLE AND
EXCLUSIVE WARRANTIES. THERE SHALL BE NO OTHER WARRANTIES EXPRESS OR IMPLIED
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS OR ANY OTHER
OBLIGATION ON THE PART OF MLI WITH RESPECT TO PRODUCTS COVERED BY THIS WARRANTY.
IN NO EVENT SHALL THE WARRANTIES OF MLI REQUIRE MORE FROM MLI THAN THE REPAIR OR
REPLACEMENT OF ANY PART OR PARTS WHICH ARE FOUND TO BE DEFECTIVE WITHIN THE
EFFECTIVE PERIOD OF THE WARRANTY, MLI SHALL HAVE NO LIABILITY FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
MILLER LOADERS INC, 1242 ARIZONA AVE, LARCHWOOD, IA 51241
PHONE: [phone]
Or [phone]
FAX: [phone]