Miller Dynasty 210 DX User manual

OWNER’S MANUAL
OM-267 827C 2015−05
Dynasty210 DX and 280 DX
AC Independent Expansion
ORIGINAL INSTRUCTIONS − PRINTED IN USA ©2015 Miller Electric Mfg. Co.
Read and follow the power source Owner’s Manual and labels carefully before installing, operating, or servicing unit.
Read the safety information at the beginning of the manual and in each section.
1-1. Software Expansion
12
.A software update is required to ensure proper
operation of all purchased feature expan-
sions. For instructions to download TIG Soft-
ware updates, see PDF file F269272A on soft-
ware expansion memory card.
Card Requirements:
.Purchased software expansion memory card
required.
1 Memory Card Port
2 Indicator LED
Enabling Software Expansion:
Insert card containing software expansion into
port.
LED indicator blinks green while machine is read-
ing from or writing to the card. After successfully
readingfrom or writing to the card, the LED switch-
es from blinking green to continuous green. The
machineis now ready to use software expansion.
Do not remove card while LED is blinking green.
.Software expansion card must remain in memory
card port to enable software expansion.
Disabling Software Expansion:
Remove the software expansion card from the
memorycard port.
Troubleshooting:
Problem: Indicator LED is continuous red.
Remedy: Remove and reinsert card. If problem
continues,the card is bad. Contact Factory Autho-
rized Service Center for a replacement card.
The memory card port uses an SD memory card.
The SD Logo is a trademark of the SD-3C LLC
Company.

OM−267 827 Page 2
1-2. AC Independent Amplitude (Dynasty DX Models Only)
1
2
3
1 AC Waveshape Control
Press switch pad until desired function is select-
ed.
2 Encoder Control (Set Value)
3 Ammeter (Displays Value)
4 Voltmeter (Parameter Selection)
EN Amperage [EN] -Use with AC TIG only to se-
lect electrode negative amperage value.
EP Amperage [EP] -Use with AC TIG only to se-
lect electrode positive amperage value.
.Both Balance and AC Frequency LEDs light
wheneither EN or EP Amperage is selected.
5 AmperageControl
Average Amperage Control: Setting EN Am-
perage,EP Amperage, Balance, and Frequency
values creates an average amperage. The oper-
ator can change the average amperage value
whilemaintaining the same EN amperage to EP
amperageratio at the existing balance and fre-
quency. To change the average amperage value,
press the Amperage switch pad and turn the En-
coder control. The changing average value is dis-
playedon the ammeter. Example: If EN Amper-
age is 150, EP Amperage is 100, Balance is 75%,
and Frequency is 120, the average amperage is
138 amps. If you press the Amperage switch pad
and turn the Encoder control until 69 amps is dis-
played,the EN amperage is now 75 and EP am-
perageisnow 50. The balance remains 75%, and
the frequency is still 120, and the 1.5 to 1 EN am-
perageto EP amperage ratio is maintained.
5
4
150 A
150 A
EN
EP
1-3. AC Independent Waveshape (Dynasty DX Models Only)
.See Dynasty 210 DX and 280 DX Opera-
tion section in Owner’s Manual for addi-
tionalinformation on Accessing User Set-
up Menu. The [ACEN], [ACEP] option re-
places the [AC] option.
1 Amperage (A) Control
2 Gas/DIG Control
3 Parameter Display
Press Gas/DIG control until [ACEN] is dis-
played.Press the Amperage (A) control to tog-
gle between [ACEN] and [ACEP].
4 Setting Display
5 Encoder Control
Use Encoder to select between advanced
squarewave [ADVS], soft squarewave
[SOFT], sine wave [SINE], or triangle wave
[TRI]. The default is [SOFT].
MENU
1
345
USER
SOFT
SOFT
ACEN
ACEP
2