Mills A-WAH09 Quick guide

INSTALLATION AND INSTRUCTION MANUAL
LED AREA LUMINAIRE
PLEASE READ ALL INSTRUCTIONS BEFORE
ATTEMPTING INSTALLATION
» To prevent personal injury or product damage only licensed electricians
should install.
» To avoid electric shock or component damage disconnect power before
attempting installation or servicing.
» This product must be installed in accordance with the national electric code (NEC)
and all applicable federal, state and local electric codes and safety standards.
» Disconnect product and allow cooling prior to servicing.
» Any alteration or modication of this product is expressly forbidden as it
may cause serious personal injury, death, property damage and/or product
malfunction.
» To prevent product malfunction and/or electrical shock this product must be
properly grounded.
» This luminaire is designed to operate in ambient temperatures ranging from -40°C
to 45°C and to be horizontally mounted with the LEDs facing down.
» This product must be installed in accordance with the applicable installation code
by a Person familiar with the construction and operation of the product and the
hazards involved.
» MIN 75°C SUPPLY CONDUCTORS
» CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH
CIRCUIT CONDUCTOR
» CAUTION - RISK OF FIRE
» Sliptter Mounted with PHOTOCELL function elevation angle should not exceed
15 degrees
Black
White Neutral
Green/Yellow Green
Ground
Line
Purple
DIM+
Gray
DIM-
BLACK
BLACKBLACK
INPUT
LAMPLOAD
RED
PHOTOCONTROL
MOTION SENSOR
WHITE
WHITEWHITE
WARNING
(Figure 1)
Twisted photocell (optional)
PM4*12(mm) Screws
Side plate
OPEN
Mounting bracket
5/16’’*1.02(inch) UNC Screws
1/2’’*1.97(inch)
UNC Screws
Round pole
mounting plate
Motion Sensor (optional)
PM4*8(mm)
Screws
Side plate (Figure 2)
5/16’’*1.02(inch) UNC Screws
Twisted photocell (optional)
M8*20(mm) Screws
PM4*12(mm) Screws
(Figure 3)
5/16’’*1.02(inch) UNC Screws
Twisted photocell (optional)
PM4*8(mm) Screws
Motion Sensor (optional)
Back plate
Side plate
1/2’’1.46(inch) UNC Screws
PM4*12(mm) Screws
KM4*10(mm) Screws
OPEN
Square/Round Pole
1. Remove the side plate from mounting bracket. Please skip to step 3 if mounted
onto the square Pole.
2. Attach round pole mounting plate on mounting bracket.
3. Route the cord into mounting bracket through the hole for wiring, slide the xture
onto the bracket and tighten 2 bottom screws.
4. Slightly drag the wires to make sure the hole on bracket is sealed by
silicon gasket.
5. Make wiring connection as per wire diagram below, replace the side plate and
fasten screws.
Sliptter
1. Connect the wires to L / N / GND
2. Remove the cover and adjust the bracket to the desired angle
3. Install the bracket on the pole and x it with screws
Wall Mount
1. Remove the side plate by loosen the screws.
2. Fix the back plate onto the arm bracket with screws provided.
3. Use the metal template provided to locate footprint on the wall to drill the holes,
then x the bracket on the wall with screws.
4. Route the power cord into wall mount bracket, slide the xture onto the mounting
bracket, then tighten bottom screws.
5. Make wiring connection inside of bracket and replace the side plate with screws.

Slipfitter Mount
QuantityMounting Type
1
Specifications
Adjustable slipfitter
Square mount
2
Round mount
# 1/2'' x 1.97'' Stainless Steel Hexagon
Hexagon head bolt
120-277V 3-Pin
2
3-Pin receptacle
1
1
1
PM4 x 8 Stainless Steel,
Round Flat bottom Bolt
2
120-277V 0-10V Bi-level
1
# 1/2'' x 1.97'' Stainless Steel Hexagon
Hexagon head bolt
1
19.9 x 17.7 x 9cm Square
pole mount arm
17.7 x 8.8 x 1.3cm Round pole adaptor
Wall mount
Others
①
①③
③
②
②
②
②
Accessory
Slipfitter
2
Bolt
# 1/2'' x 1.46'' Stainless Steel
Hexagon head bolt
4
Bolt
KM4 x 10'' Stainless Steel flat head bolt
1
Bolt
20.3 x 15.2 x 0.5cm Steel Plate
1
Wall Mount Plate
20.3 x 15.2 x 0.1cm Aluminum alloy plate
1
Wall Mount Template
19.9 x 17.7 x 9cm Square pole mount arm Pole Mout Arm
Twist-lock photocell
Receptacle
Bolt
Occupancy Sensor
Bolt
Pole Mout Arm
Adaptor
1Pole Mout Arm
19.9 x 17.7 x 9cm Square
pole mount arm
①
①
①② ③
④④
⑤
⑤
①
②
③
INSTALLATION AND INSTRUCTION MANUAL
LED AREA LUMINAIRE
MillsLabs.com
Accessory List