Milwaukee CABLE DRIVE 47-53-2816 User manual

IMPORTANT SAFETY INSTRUCTIONS
WARNING
FUNCTIONAL DESCRIPTION
•
•
• Cable tip may be sharp.
Cat. No.: 47-53-2816
CABLE DRIVE™ ASSEMBLY FOR M18™
DRUM MACHINE
TO REDUCE THE RISK OF
INJURY, USER MUST READ
OPERATOR'S MANUAL AND ALL LABELS FOR
THIS ACCESSORY, THE TOOL, AND THE
BATTERY. Failure to follow all instructions listed
below may result in electric shock, fire and/or
serious injury. SAVE THESE INSTRUCTIONS - THIS
OPERATOR’S MANUAL CONTAINS IMPORTANT
SAFETY AND OPERATING INSTRUCTIONS.
Use latex or rubber gloves inside the gloves
recommended by the manufacturer, goggles, face
shields, protective clothing, and respirator when
chemicals, bacteria and other toxic or infectious
substances are suspected to be in a drain line.
Drains may contain chemicals, bacteria, and
other substances that may cause burns, be toxic
or infectious or may result in other serious
personal injury.
Only use cables that range between 9.5 mm (3/8")
and 12.7 mm (1/2").
SPECIFICATIONS
For use with ............................................. M18 BCDM
Compatible with MILWAUKEE®
cables...........................................................48532776
...........................................................48532777
...........................................................48532778
7.
5.
6.
8.
Remove mounting plate from the Cable Drive™
Assembly by rotating plate anti-clockwise.
4. Remove the Cable Drive™ Assembly from the
cable. Refer to the Brushless Compact Drum
Machine manual.
3. Remove mounting plate from the Cable Drive™
Assembly.
2. Remove Cable Accessory from cable - Refer to
Brushless Compact Drum Machine manual .
Align mounting plate to the four screws holes on the
front of the drum attachment block.
Use the four T20 screws and fasten mounting plate
to the front of the drum attachment block using a
T20 bit.
The mounting plate is now ready for the Cable
Drive™ Assembly.
Screw
Mounting
Plate
1.
2.
3.
4.
Installing the Cable Drive™ Assembly onto
the Mounting Plate
Align the attachment to the mounting plate using the
two alignment lines shown in figure 3.
Press the Cable Drive™ Assembly flush against the
mount.
Rotate the attachment clockwise until it clicks.
The Cable Drive™ Assembly attachment is now
ready to use.
1
Guide tube
mount
Cable feed
ratchet lever
Cable feed quick
release button
Feed
handle
ASSEMBLY
WARNING
Installing the Mounting Plate
1.
Always remove battery pack
before changing or removing
accessories. Only use accessories specifically
recommended for this tool. Others may be
hazardous.
Inspect mounting plate and Cable Drive™ Assembly
before use.
Remove battery pack.
Alignment
lines
Figure 1
Figure 2 Figure 3
Alignment
lines
Mounting
plate

2
OPERATION
WARNING
Using the Cable Feed Assembly
To use the cable feed:
1. Insert the battery pack.
3.
6.
5.
7.
8.
4
6
7
5
Move the Forward/OFF/Reverse switch to
Forward
2.
Ensure the alignment lines as shown in figure 2 are
aligned. This will disengage the cable advancement
function.
4. Use the foot pedal to start the drum.
To engage the cable feed, press the cable feed
ratchet lever down.
NOTE: Do not over-press the lever arm. Flexible
cable requires less force to feed the cable while stiff
cable requires more force to feed the cable.
To advance the cable, push the cable feed handle
clockwise The further the handle is pushed, the
faster the cable will advance.
To retract the cable, push the cable feed handle
anti-clockwise The further the handle is pushed,
the faster the cable will retract.
To stop the cable from advancing or retracting,
disengage the cable feed by pressing the quick
release button. Move the cable feed ratchet lever to
the centre to slow/stop the cable.
The cable feed can be used to assist in advancing and
retrieving the cable.
To reduce the risk of injury,
wear safety goggles or glasses
with side shields. Use latex or rubber gloves inside
the gloves recommended by the manufacture to
avoid entanglement. Cable tip may be sharp.

3
MAINTENANCE
WARNING
Maintaining Tool
Cleaning
Greasing the Cable Feed
Apply grease to the cable feed after each use.
Zerk Fittings
Oiling the Cable Feed Bearings
1. Remove battery pack.
2. Press the quick release button.
3.
5.
Nose of Cable Feed
Bearings
To reduce the risk of injury,
always unplug the charger and
remove the battery pack from the charger or tool
before performing any maintenance. Never
disassemble the tool, battery pack or charger.
Contact a MILWAUKEE®service facility for ALL
repairs.
Keep your tool in good repair by adopting a regular
maintenance program. Return the tool to a
MILWAUKEE®service facility for repair.
Clean dust and debris from vents. Keep handles clean,
dry and free of oil or grease. Use only mild soap and a
damp cloth to clean, since certain cleaning agents and
solvents are harmful to plastics and other insulated
parts. Some of these include petrol, turpentine, lacquer
thinner, paint thinner, chlorinated cleaning solvents,
ammonia and household detergents containing
ammonia. Never use flammable or combustible
solvents around tools.
Push the cable feed handle to the maximum retract
position
4. Apply bearing grease to the upper Zerk fitting,
sufficiently covering the fitting.
Press the cable feed ratchet lever down.
6. Push the cable feed handle to the maximum feed
position
7. Apply bearing grease to the two lower Zerk fittings,
sufficiently covering the fittings.
1. Remove battery pack.
2. Press the quick release button.
3.
5.
Use a hose to clean out the cable feed with clean
water to remove contaminants. Drain the drum
completely by removing the drum plug.
4. Move the cable feed handle to the maximum retract
position and apply a penetrating oil into the nose
of the cable feed directly onto all three bearings.
Sufficiently cover the bearing seals.
Move the cable feed handle to the maximum feed
position and repeat.
6. Press the ratchet lever down and then feed and
retract the cable 30-60 cm (1-2 feet) multiple times
to work the oil around.
7. Repeat after each use.
Keep all exposed, moving, and rotating parts cleaned
and properly oiled after each use.

WARRANTY - AUSTRALIA and NEW ZEALAND
SERVICE - AUSTRALIA and NEW ZEALAND
MILWAUKEE®prides itself in producing a premium quality product that is Nothing But Heavy DutyTM.
Your satisfaction with our products is very important to us! If you encounter any problems with the
operation of this tool, please contact your authorised MILWAUKEE®dealer.
For a list of MILWAUKEE®dealers, guarantee or service agents please contact MILWAUKEE®
Customer Service or visit our website.
(Australia Toll Free Telephone Number 1300 645 928)
(New Zealand Toll Free Telephone Number 0800 645 928)
or visit milwaukeetool.com.au/milwaukeetool.co.nz.
Please refer to Australian and New Zealand warranty supplied with tool. This warranty applies only to
product sold by authorised dealers in Australia and New Zealand.
961014549-01(A)
Milwaukee Electric Tool Corporation
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Tool (Australia)
21 Kelletts Road, Rowville, VIC 3178
Melbourne, Australia
Milwaukee Tool (New Zealand)
274 Church Street, Penrose,
Auckland, 1061, New Zealand
DESIGNED BY MILWAUKEE ELECTRIC TOOL CORP.
PROFESSIONALLY MADE IN CHINA
PRINTED IN CHINA