Milwaukee sds 5363-21 User manual

Cat. No.
No de cat.
5363-21
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S
MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN
COMPRENDRE LE MANUEL DE L'UTILISATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL
MANUAL DEL OPERADOR.
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
1" COMPACT SDS ROTARY HAMMER
MARTEAU ROTATIF 26 mm (1")
26 mm (1") ROTOMARITILLOS
SDS

23
PERSONAL SAFETY
GENERAL POWER TOOL SAFETY WARNINGS
WORK AREA SAFETY
ELECTRICAL SAFETY
•Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
•Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids,gasesordust.Powertoolscreatesparks
which may ignite the dust or fumes.
•Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
•Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodifiedplugs and matching outletswill
reduce risk of electric shock.
•Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators.Thereisanincreasedriskofelectric
shock if your body is earthed or grounded.
•Do not expose power tools to rain orwetcondi-
tions. Water entering a power tool will increase
the risk of electric shock.
•Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
•When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.
•If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. UseofanRCDreduces
the risk of electric shock.
•Remove any adjusting key or wrench before
turning the power tool on. Awrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
•Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
•Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
•If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS.
Failure to follow the warnings and instructions may result in electric shock, fire and/or
serious injury. Save all warnings and instructions for future reference
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
POWER TOOL USE AND CARE
•Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
•Do not use thepower tool if theswitch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
•Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
•Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Powertools are dangerous in the
hands of untrained users.
•Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Manyaccidents
are caused by poorly maintained power tools.
•Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
•Use the power tool, accessories and tool bits
etc., in accordance with these instructions,
taking into account theworking conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
•Stay alert, watch what you are doing and use
common sensewhen operating apower tool.Do
not use apower tool whileyou aretired or under
theinfluenceof drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
•Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearingprotection used for appropriate conditions
will reduce personal injuries.
•Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carryingpowertoolswith
yourfingeron the switch or energising power tools
that have the switch on invites accidents.
SERVICE
•Have your power tool serviced by a qualified
repair person using only identical replacement
parts. Thiswill ensure that the safety ofthe power
tool is maintained.

45
SPECIFIC SAFETY RULES
•Wear ear protectors. Exposure to noise can
cause hearing loss.
•Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
•Hold power toolsby insulatedgripping surfaces,
when performingan operation wherethe cutting
tool may contact hidden wiring or its own cord.
Cutting accessory contacting a live wire may make
exposedmetal parts ofthepowertoollive and could
give the operator an electric shock.
•Keep hands away from all cutting edges and
moving parts.
•Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
•WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
•lead from lead-based paint
•crystalline silica from bricks andcementand other
masonry products, and
•arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment,suchasthosedust masks that are spe-
cially designed to filter out microscopic particles.
Fig. B Fig. C
Fig. A
GROUNDING
WARNING Improperly connecting the
grounding wire can result in the risk of
electric shock. Check with a qualified electri-
cian if you are in doubt as to whether the
outlet is properly grounded. Do not modify
the plug provided with the tool. Never remove
the grounding prong from the plug. Do not
use the tool if the cord or plug is damaged. If
damaged, have it repaired by a MILWAUKEE
service facility before use. If the plug will not
fit the outlet, have a proper outlet installed by
a qualified electrician.
Grounded Tools: Tools with Three Prong Plugs
Tools marked “Grounding Required” have a three
wire cord and three prong grounding plug. The
plug must be connected to a properly grounded
outlet (See FigureA). If the tool should electrically
malfunction or break down, grounding provides a
low resistance path to carry electricity away from
the user, reducing the risk of electric shock.
The grounding prong in the plug is connected
through the green wire inside the cord to the
grounding system in the tool. The green wire in the
cord must be the only wire connected to the tool's
grounding system and must never be attached to
an electrically “live” terminal.
Your tool must be plugged into an ap-
propriate outlet, properlyinstalled and
groundedinaccordancewithallcodes
and ordinances. The plug and outlet
should look like those in FigureA.
Double Insulated Tools: Tools with Two Prong
Plugs
Tools marked “Double Insulated” do not require
grounding. They have a special double insula-
tion system which satisfies OSHA requirements
and complies with the applicable standards of
Underwriters Laboratories, Inc., the
CanadianStandardAssociationand
theNationalElectricalCode.Double
Insulatedtoolsmaybeusedineither
of the 120 volt outlets shown in
Figures B and C.
FUNCTIONAL DESCRIPTION Grounded tools require a three wire extension
cord. Double insulated tools can use either a two
or three wire extension cord. As the distance from
thesupplyoutletincreases, you must use a heavier
gauge extension cord. Using extension cords with
inadequately sized wire causes a serious drop in
voltage,resulting in loss of power andpossible tool
damage.Refer to the table shownto determine the
required minimum wire size.
The smaller the gauge number of the wire, the
greater the capacity of the cord. For example, a 14
gauge cord can carry a higher current than a 16
gauge cord. When using more than one extension
cordto make up thetotal length, be sure eachcord
containsat least the minimumwiresize required. If
youareusingoneextensioncord for more than one
tool, add the nameplate amperes and use the sum
to determine the required minimum wire size.
Guidelines for Using Extension Cords
•If you are using an extension cord outdoors,
be sure it is marked with the suffix “W-A” (“W”
in Canada) to indicate that it is acceptable for
outdoor use.
•Be sure your extension cord is properly wired
and in good electrical condition. Always replace
a damaged extension cord or have it repaired by
a qualified person before using it.
• Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
READ AND SAVE ALL
INSTRUCTIONS FOR FUTURE USE.
Recommended Minimum Wire Gauge
for Extension Cords*
Extension Cord Length
*Based onlimiting theline voltage drop to fivevolts
at 150% of the rated amperes.
Nameplate
Amperes
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 16.0
16.1 - 20.0
25'
18
18
18
18
16
14
12
75'
18
18
16
14
12
10
100'
18
16
14
12
10
150'
16
14
12
12
50'
18
18
18
16
14
12
10
EXTENSION CORDS
SPECIFICATIONS
Tool Capacities
Cat. No. Volts AC A
No
Load
RPM No Load BPM
Drill Only Rotary Hammer
Twist
Drill Bit
(Steel)
Twist
Drill Bit
(Wood)
Carbide Tipped
Percussion Bit
(concrete)
Thin Wall
Core Bit
(concrete)
Thin Wall
Core Bit
(brick/block)
5363-21 120 7 0-1400 0-5980 1/2" 1-1/4" 1" 2-1/2" 2-5/8"
SYMBOLOGY
Double Insulated
Volts Alternating Current
Amps
No Load Revolutions per Minute
(RPM)
BPM Blows per Minute (BPM)
Mexican Approvals Marking
Underwriters Laboratories, Inc.
United States and Canada
1. Side handle
2. Clamp
3. Depth gauge rod
4. SDS Plus bit holder
5. Trigger
6. Forward/Reverse Control
7. Mode selector lever switch
2
1
3
5
4
6
7

67
WARNING To reduce the risk of injury,
always use a side handle when using
this tool. Always brace or hold securely.
ASSEMBLY
WARNING To reduce the risk of injury,
always unplug tool before attaching
or removing accessories or making adjust-
ments. Use only specifically recommended
accessories. Others may be hazardous.
OPERATION
WARNING To reduce the risk of injury,
always unplug tool before attaching
or removing accessories or making adjust-
ments. Use only specifically recommended
accessories. Others may be hazardous.
WARNING To reduce the risk of injury,
keep hands and cord away from the bit
and all moving parts.
WARNING To reduce the risk of injury,
wear safety goggles or glasses with side
shields.
Drilling
Depth
Bit holder
release
collar
Adapter
Core
Bit
Center
Pin
Guide
Plate
Clean
and
lubricate
threads
Adjusting the Side Handle Position
1. Loosen the side handle by unscrewing the side
handle grip until the side handle rotates freely.
2. Rotate the side handle to the desired position.
3. Tighten the side handle grip securely.
Setting the Depth Gauge
1. Press in the clamping lever.
2. Slide the depth gauge rod backward or forward
until it is set for the desired depth.
NOTE: The drilling
depth is the distance
between the tip of the
bit and the tip of the
depth gauge rod.
3. Release the clamping lever.
Installing Drill Bits and Chisels
NOTE: Only use accessories with SDS or SDS
Plus shanks.
Be sure that the shank of the bit is clean. Dirt par-
ticlesmaycausethebittolineupimproperly.Do not
use bits larger than the maximum recommended
capacity of the drill because gear damage or mo-
tor overloading may result. For best performance,
be sure that the bit is properly sharpened and the
shank is lightly greased before use.
1. Insert the bit or chisel into the nose of the tool.
2. Rotate bit slowly until it aligns with the locking
mechanism.
3. Push bit into tool until it locks.
4. Check that the bit is locked properly; it should
be possible to pull the bit back and forth slightly
(about 1/4”).
5. To remove bits and
chisels, pull bit holder
release collar toward
the rear of tool and
remove bit.
NOTE: Use caution
when handling hot
bits and chisels.
Selecting Action
MILWAUKEERotaryHammershave three settings:
drill only, rotary hammer, and hammer only.
1. For drilling, turn the
selector lever so the
arrow on the lever
points to the twist
drill symbol.
2. For rotary hammer-
ing, turn the selector
lever so the arrow
points to the ham-
mer and twist drill
symbol.
3. For hammering only, turn the selector lever so
the arrow points to the hammer symbol.
4. To freely rotate the bit to the desired angle for
chiselingonly,turn the selector lever so the arrow
points to the Osymbol. Then, follow step 3.
Using the Control Switch
The control switch may be set to three positions:
forward,reverseand lock. Due to a lockoutmecha-
nism,the control switch can onlybeadjusted when
the trigger is not pulled.Always allow the motor to
come to a complete stop before using the control
switch.
For forward (clockwise)
rotation, push the control
switch to the left side of the
tool. Check the direction of
rotation before use.
For reverse (counterclock-
wise) rotation, push the control switch to the right
side of the tool. Check direction of rotation before
use.
Starting, Stopping and Controlling Speed
1. To start the tool, grasp the handlefirmlyand pull
the trigger.
2. To vary the speed, increase or decrease the
pressure on the trigger. The further the trigger
is pulled, the greater the speed.
3. To stop the tool, release the trigger. Make sure
the tool comes to a complete stop before laying
the tool down.
Operating
Position the tool, grasp the handles firmly and pull
thetrigger.Alwaysholdthe tool securely using both
handles to maintain control. This tool has been
designed to achieve top performance with only
moderate pressure. Let the tool do the work.
If the speed begins to drop off when drilling large
or deep holes, pull the bit partially out of the hole
while the tool is running to help clear dust. Do not
use water to settle the dust since it will clog the bit
flutes and tend to make the bit bind in the hole. If
the bit should bind, a built-in, non-adjustable slip
clutch prevents the bit from turning. If this occurs,
stop the tool, free the bit and begin again.
Using Core Bits
Core bits are useful for drilling large holes for
conduit and pipe. MILWAUKEE Heavy-Duty Thin
Wall Core Bits have heat treated steel bodies with
durable carbide tips. They are specially designed
forfast,accurate drilling with combined hammering
and rotary action.
1. Cleanandlubricate the threads
on the adapter and core bit as
indicatedtomake later removal
easier.Screw the threaded end
of the adapter into the rear of
the core bit.
2. Push the guide plate onto the
pointed end of the center pin.
Insert the center pin with guide
plate assembly into to the core
bit. Besurethesmallendofthe
center pin is securely placed
intothe hole in the centerof the
adapter.
3. Insert the adapter into the bit
holder of the tool as described
in “Inserting Drill Bit or Chisel”.
Set the rotary hammer/drill
lever to rotary hammer.
4. Press the center pin firmly
against your center mark, hold
the tool firmly and pull the trig-
ger.
5. After drilling to about the depth
of the core bit teeth, remove
the center pin and guide plate from the core bit.
Resume drilling.
6. Afteryou have finished drillingthe hole, hold the
tool upwards, pointing it away from your body,
and run it briefly in forward to loosen the core
bit from the adapter.
MILWAUKEE Heavy-Duty Thin Wall Core Bits
drill holes up to 3" deep. To make deeper holes,
remove the bit, break and remove the core. Re-
sume drilling.
Forward Reverse
APPLICATIONS
Drilling in Wood, Composition Materials and
Plastic
When drilling in wood, composition materials and
plastic, select the drill operating mode. Start the
drill slowly, gradually increasing speed as you drill.
Select low speeds for plastics with a low melting
point.
Drilling in Metal
When drilling in metal, select the drill operating
mode. Use high speed steel twist drills or hole
saws. Use a center punch to start the hole. Lubri-
cate drill bits with cutting oil when drilling in iron
or steel. Use a coolant when drilling in nonferrous
metals such as copper, brass or aluminum. Back
the material to prevent binding and distortion on
breakthrough.
Drilling in Masonry
Whendrilling in masonry, select the rotary hammer
operating mode. Use high speed carbide-tipped
bits. Drilling soft masonry materials such as cinder
block requires little pressure. Hard materials like
concrete require more pressure. A smooth, even
flow of dust indicates the proper drilling rate. Do
not let the bit spin in the hole without cutting. Do
not use water to settle dust or to cool bit. Do not
attempt to drill through steel reinforcing rods. Both
actions will damage the carbide.

89
MAINTENANCE
WARNINGTo reduce the risk of injury,
always unplug your tool before per-
forming any maintenance. Never disas-
semble the tool or try to do any rewiring
on the tool’s electrical system. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Tools
Keepyour tool in goodrepair by adopting a regular
maintenance program. Before use, examine the
general condition of your tool. Inspect guards,
switches, tool cord set and extension cord for
damage. Check for loose screws, misalignment,
binding of moving parts, improper mounting, bro-
ken parts and any other condition that may affect
its safe operation. If abnormal noise or vibration
occurs, turn the tool off immediately and have the
problemcorrected before further use. Donot use a
damaged tool. Tag damaged tools “DO NOT USE”
until repaired (see “Repairs”).
Undernormalconditions,relubricationisnotneces-
sary until the motor brushes need to be replaced.
After six months to one year, depending on use,
returnyourtooltothenearestMILWAUKEE service
facility for the following:
• Lubrication
• Brush inspection and replacement
•Mechanical inspection and cleaning (gears,
spindles, bearings, housing, etc.)
• Electrical inspection (switch, cord, armature, etc.)
• Testing to assureproper mechanical andelectrical
operation
WARNINGTo reduce the risk of injury,
electric shock and damage to the tool,
never immerse your tool in liquid or allow a
liquid to flow inside the tool.
Cleaning
Clean dust and debris from vents. Keep the tool
handles clean, dry and free of oil or grease. Use
only mild soap and a damp cloth to clean your tool
since certain cleaning agents and solvents are
harmfulto plastics and other insulated parts.Some
ofthese include: gasoline, turpentine, lacquerthin-
ner, paint thinner, chlorinated cleaning solvents,
ammonia and household detergents containing
ammonia. Never use flammable or combustible
solvents around tools.
Repairs
If your tool is damaged, return the entire tool to the
nearest service center.
ACCESSORIES
For a complete listing of accessories refer to your
MILWAUKEE Electric Tool catalog or go on-line
to www.milwaukeetool.com. To obtain a catalog,
contact your local distributor or a service center.
WARNINGTo reduce the risk of injury,
always unplug the tool before attaching
or removing accessories. Use only specifi-
cally recommended accessories. Others may
be hazardous.
TECHTRONIC INDUSTRIES' warranty is for 5 year since the original purchase date.
This warranty card covers any defect in material and workmanship on this Power Tool.
To make this warranty valid, present this warranty card, sealed/stamped by the distributor or store where you purchased the
product, to the Authorized Service Center (ASC). Or, if this card has not been sealed/stamped, present the original proof of
purchase to theASC.
Call toll-free 1 800 832 1949 to find the nearestASC, for service, parts, accessories or components.
Procedure to make this warranty valid
Take the product to theASC,alongwiththewarrantycardsealed/stamped by the distributor or store whereyoupurchasedthe
product, and there any faulty piece or component will be replaced without cost for you. We will cover all freight costs relative
with this warranty process.
Exceptions
This warranty is not valid in the following situations:
a) When the product is used in a different manners from the end-user guide or instruction manual.
b) When the conditions of use are not normal.
c) When the product was modified or repaired by people not authorized by TECHTRONIC INDUSTRIES.
Note: If cord set is damaged, it should be replaced by anAuthorized Service Center to avoid electric risks.
SERVICEAND ATTENTION CENTER
Rafael Buelna No.1.
Col. Tezozomoc Mexico, Azcapotzalco D.F.
Ph. 01 800 832 1949
IMPORTEDAND COMMERCIALIZED BY:
TECHTRONIC INDUSTRIES MEXICO, .S.A. DE C.V.
Av. Santa Fe 481 piso 6, Col. Curz Manca.
CP 05349, Cuajimalpa, D.F.
LIMITED WARRANTY - USAAND CANADA
LIMITED WARRANTY - MEXICO, CENTRAL AMERICA AND CARIBBEAN
Model:
Date of Purchase:
Distributor or Store Stamp:
Every MILWAUKEE power tool (including cordless product – tool, battery pack(s) - see separate & distinct CORDLESS BAT-
TERYPACKLIMITEDWARRANTYstatements&batterycharger andWorkLights*)is warrantedtotheoriginalpurchaser only
tobefreefromdefects inmaterial andworkmanship. Subjecttocertainexceptions,MILWAUKEEwillrepairorreplaceanypart
on an electric power tool which, after examination, is determined by MILWAUKEE to be defective in material or workmanship
for a period of five (5) years* after the date of purchase unless otherwise noted. Return of the power tool to a MILWAUKEE
factoryServiceCenterlocationorMILWAUKEEAuthorizedService Station, freight prepaid and insured, is required. Acopy of
the proof of purchase should be included with the return product. This warranty does not apply to damage that MILWAUKEE
determinestobefromrepairsmadeorattemptedbyanyoneotherthanMILWAUKEEauthorizedpersonnel,misuse,alterations,
abuse, normal wear and tear, lack of maintenance, or accidents.
*Thewarranty period for,Job SiteRadios, M12™ Power Port andTradeTitan™Industrial WorkCarts isone (1) year from the
dateofpurchase. ThewarrantyperiodforaLEDWorkLightandLEDUpgradeBulbisalimitedLIFETIMEwarrantytotheoriginal
purchaser only, if during normal use the LED bulb fails the Work Light or Upgrade Bulb will be replaced free of charge.
*This warranty does not coverAir Nailers & Stapler,Airless Paint Sprayer, Cordless Battery Packs, Gasoline Driven Portable
PowerGenerators, HandTools, Hoist –Electric,Lever & HandChain,M12™ Heated Jackets,ReconditionedproductandTest
& Measurement products. There are separate and distinct warranties available for these products.
Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE power tool product. The manu-
facturing date of the product will be used to determine the warranty period if no proof of purchase is provided at the time
warranty service is requested.
ACCEPTANCEOFTHEEXCLUSIVEREPAIRANDREPLACEMENTREMEDIESDESCRIBEDHEREINISACONDITIONOF
THECONTRACTFORTHEPURCHASEOFEVERYMILWAUKEEPRODUCT. IFYOUDONOTAGREETOTHISCONDITION,
YOUSHOULD NOTPURCHASETHEPRODUCT. INNO EVENTSHALLMILWAUKEE BE LIABLE FORANYINCIDENTAL,
SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FORANY COSTS,ATTORNEY FEES, EXPENSES, LOSSES
ORDELAYSALLEGEDTOBEASACONSEQUENCE OFANYDAMAGETO,FAILUREOF,ORDEFECTINANYPRODUCT
INCLUDING,BUTNOTLIMITEDTO,ANYCLAIMSFORLOSSOFPROFITS. SOMESTATESDONOTALLOWTHEEXCLU-
SION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIALDAMAGES, SO THEABOVE LIMITATION OR EXCLUSION
MAY NOTAPPLY TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES,
WRITTEN OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES,
INCLUDINGWITHOUTLIMITATIONANYIMPLIEDWARRANTYOFMERCHANTABILITYORFITNESSFORAPARTICULAR
USE OR PURPOSE; TOTHE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES
ARELIMITEDTOTHEDURATIONOFTHEAPPLICABLEEXPRESSWARRANTYASDESCRIBEDABOVE. SOMESTATES
DONOTALLOWLIMITATIONSON HOW LONGAN IMPLIEDWARRANTYLASTS, SO THEABOVE LIMITATIONMAYNOT
APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGALRIGHTS, ANDYOU MAYALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the ‘Service Center Search’ in the Parts & Service section of MILWAUKEE’s website www.milwaukeetool.com
or call 1.800.SAWDUST(1.800.729.3878) to locate your nearest MILWAUKEE factory Service Center location.