Mindray iMEC15S User manual

I
Intellectual Property Statement
SHENZHEN MINDRAY BIO-MEDICAL ELECTRONICS CO., LTD. (hereinafter called Mindray) owns the intellectual property
rights to this product and this manual. This manual may refer to information protected by copyrights or patents and
does not convey any license under the patent rights of Mindray, nor the rights of others. Mindray does not assume any
liability arising out of any infringements of patents or other rights of third parties.
Mindray intends to maintain the contents of this manual as confidential information. Disclosure of the information in
this manual in any manner whatsoever without the written permission of Mindray is strictly forbidden. Release,
amendment, reproduction, distribution, rent, adaptation and translation of this manual in any manner whatsoever
without the written permission of Mindray is strictly forbidden.
, , and are the registered trademarks or trademarks owned by Mindray in
China and other countries. All other trademarks that appear in this manual are used only for editorial purposes
without the intention of improperly using them. They are the property of their respective owners.
Contents of this manual are subject to changes without prior notice.
Revision History
This manual has a revision number. This revision number changes whenever the manual is updated due to software or
technical specification change. Contents of this manual are subject to change without prior notice.
Revision number: 6.0
Release time: May 2017
© 2011 - 2017 Shenzhen Mindray Bio-Medical Electronics Co., Ltd. All rights reserved.











1-2
1.1.1 Dangers
There are no dangers that refer to the product in general. Specific “Danger” statements may be given in the respective
sections of this manual.
1.1.2 Warnings
WARNING
All installation operations, expansions, changes, modifications and repairs of this product are conducted
by Mindray authorized personnel.
There is high voltage inside the equipment. Never disassemble the equipment before it is disconnected
from the AC power source or the battery.
When you disassemble/reassemble a parameter module, a patient leakage current test must be performed
before it is used again for monitoring.
The equipment must be connected to a properly installed power outlet with protective earth contacts
only. If the installation does not provide for a protective earth conductor, disconnect it from the power line
and operate it on battery power, if possible.
Disposal of the packaging material should observe the applicable waste control regulations. and keeping
it out of children’s reach.
1.1.3 Cautions
CAUTION
Make sure that no electromagnetic radiation interferes with the performance of the equipment when
preparing to carry out performance tests. Mobile phone, X-ray equipment or MRI devices are a possible
source of interference as they may emit higher levels of electromagnetic radiation.
Before connecting the receiver to the power line, check that the voltage and frequency ratings of the
power line are the same as those indicated on the unit’s label or in this manual.
Protect the equipment from damage caused by drop, impact, strong vibration or other mechanical force
during servicing.
1.1.4 Notes
NOTE
Refer to Operation Manual for detailed operation and other information.
1.2 Equipment Symbols
See the iMec series Operator’s Manual for information about the symbols used on this product and its packaging.






Local Display
LAN
Centeral Station
Wi-Fi
Remote Monitor
Defibrillator
Synchronized
Signal Output














Main
Board
RTC
POWER
Power
Board
AC/DC
Recorder
Speaker
Touch Screen
Control Board
Touchsc
reen LCD Screen
Alarm
Lamp
Board
IO*2
MCU
UART
Knob
IO*2
Keypad
Board
6 keys
Audio
Backlight
Control Display
LVDS
VGA DB15
Multi-
parameter
Module
LAN RJ45
USB
UART
UART
CO/IBP Module
UART
MCU
DC-DC,
Charge Control
CO2 Module
(Three types)
UART
Battery
Pause
LED
Front Housing Rear Housing
Power System
External
Device of Main
Board
Parameter
System
Interface
Board
Main PCA
Antenna
Power Switch
Board
Work
LED
CPU
WIFI
SD Card
1GB
VGA
LAN
Optional
Parameter
AC
LED
BAT
LED























MCU
UART
Encoder
Keypad board
6 keys
Pause
LED
Power on/off board
Work
LED
AC
LED
BAT
LED
Main Board

Main board
AC/DC power
board
AC
BAT
Power
management
LDO
Power
on/off LDO
5 V DC DC 12 VDC DC
VIN bus-bar voltage
Battery
back
board
//








