Minka-aire Facets User manual

CERTIFICATE

Facets

Manual design and all elements of manual design are protected by U.S. Federal and/or State Law,including Patent,Trademark and/or Copyright laws.

Minka-Aire warrants to the original owner that this fan will be free from defects in material and workmanship for one year

from the date of purchase, excluding the motor. Minka-Aire warrants to the original owner that the motor in this fan shall be free

from defects in material and workmanship for as long as the original purchaser owns the fan, and it remains in the original

installation.

This is a limited warranty. Minka-Aire ’s only obligation under this limited warranty is to replace or repair, or refund the purchase price, in Minka-

R R

Aire ’s sole discretion without charge to the original owner, of the fan once Minka-Aire confirms that the fan has a defect covered by this limited

Call our customer service department at 1-800-307-3267 to obtain the name of the

contact us through our web site, www.minkagroup.net and write to: Ask Mr.Minka if you have any questions or require further assistance.

Minka-Aire authorized dealer closest to your location, or

To obtain warranty service, the owner should return the fan along with proof of purchase to a

authorized dealer shall then, at its sole discretion: repair the fan, replace the fan,refund the purchase price less the amount directly attributable to the

R R

consumer’s prior usage of the fan, or if necessary instruct the consumer to contact Minka-Aire directly for warranty service. Minka-Aire will be

responsible for the cost of any repair, or replacement for any warranty service provided by a Minka-Aire authorized dealer for product under warranty.

R R

Minka-Aire authorized dealer. The Minka-Aire

You may also at your preference obtain warranty service by returning the fan directly to

return address, and a description of the claimed product defect. Pack carefully; damage sustained in return transit to Minka-Aire will be the original

owner’s responsibility. Original owner shall be responsible to pay all shipping charges. To obtain warranty service, you may return a fan that proves

to be defective during the warranty period to the following address:

Minka-Aire along with proof of purchase, your name and

Minka-Aire -Warranty Service,1151W.Bradford Court,Corona,CA 92882

This warranty shall not apply to fans which have been damaged in any way, including improper installation, damage as result of the removal

of the fan from the original installation, or damage in shipping. This warranty shall not apply to fans which have been subjected to use for which

the fan was not designed. The purchaser of the fan shall be responsible for any cost of removing the old fan, installing a new fan,or any other costs.

This limited warranty is in lieu of all other express warranties. This limited warranty excludes all incidental and consequential damages, and

Minka-Aire shall not under any circumstances be liable for incidental or consequential damages. Some states do not allow the exclusion of or

limitation of incidental or consequential damages, so the foregoing limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. We encourage you to promptly

complete and return the enclosed warranty registration card.However, return of the warranty registration card is not a condition of this warranty.

Date Purchased Store Purchased Model No. F613 Serial No.

CONTENTS

INSTALLING THE LIGHT KIT PLATE 8

INSTALLING THE LIGHT KIT ASSEMBLY 9

INSTALLING THE GLASS SHADE & LIGHT BULB 10

OPERATING THE REMOTE CONTROL/WALL CONTROL 11

CARE OF YOUR FAN 12

TROUBLESHOOTING 13

SPECIFICATIONS 14

SAFETY RULES

PACKAGE CONTENTS 2

INSTALLING THE FAN 3

HANGING THE FAN 4

ELECTRICAL CONNECTIONS 5

FINISHING THE INSTALLATION 6

BLADE INSTALLATION 7

SAFETY RULES

1 1.

2. Be cautious!Read all instuctions and safety information before installing your new fan. Review accompanying assembly diagrams.

3. Make sure that all electrical connections comply with local codes, ordinance, or National Electrical Codes.Hire a qualified electrician or

consult a do-it-your self wiring handbook if you are unfamiliar with installing electrical wiring.

4. Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the floor and 18 inches from the top of the blades to the wall.

5. If you are mounting the fan to a ceiling fan outlet box, use a U.L Listed metal octagonal outlet box marked"Acceptable For Fan Support".

Secure the box directly to the building structure. The outlet box and its support must be able to support the moving weight of the fan (at

least 50 pounds). Do not use a plastic box.

6. Caution: To reduce the risk of injury use only the screws provided with the outlet box in conjunction with the lock washers provided with

the fan.

7. If you are mounting the fan to a joist, make sure it is able to support the moving weight of the fan (at least 50 pounds).

8. After you install the fan, make sure that all mounting components are secured to prevent the fan from falling.

9. Do not insert anything into the fan blades while the fan is operating.

10. To operate the reverse function on this fan, press the reverse button while the fan is running.

Before you begin installing the fan, shut power off the circut breaker of the fuse box.

NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and

situations that may occur. It must be understoood that common sense,caution and care are factors which can not be built into

this product. These factors must be spplied by the person(s) installing, caring for and operating the unit.

NOTE: READ AND SAVE ALL INSTRUCTIONS!

WARNING

TO REDUCE THE RISK OF FIRE,ELECTRIC SHOCK OR OTHER PERSONAL INJURY, MOUNT FAN ONLY TO A U.L LISTED OUTLET BOX OR SUPPORTING

SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX IN CONJUCTION WITH THE

LOCK WASHERS PROVIDED WITH THE FAN. MOST OUTLET BOXS COMMONLY USED FOR FAN SUPPORT OF LIGHTING FIXTURES ARE NOT

ACCEPTABLE FOR FAN SUPPORT AND NEED TO BE REPLACED. CONSULT A QUALIFIDE ELECTRICIAN IF IN DOUBT.

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE HOLDERS WHILE INSTALLING BALANCING THE BLADES OR CLEANING

THE FAN. DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.

TO REDUCE THE RISK OF FIRE OR ELECTRONIC SHOCK, THIS FAN ONLY CAN USE UC7067RYK SOLID-STATE SPEED CONTROL WITH UC9040T

WALL CONTROL ONLY.

ATTENTION: The Energy Policy Act of 2005 requires this fan to be equipped with a 190 watt limiting device, If lamping exceeds

190watts, the ceiling fan’s light kit will shut off automatically.

PACKAGE CONTENTS

Unpack your fan and check the contents.You should have the following items:

A. Mounting hardware:

Wire nuts(3)

Machine screws (2)

Wood screws (2)

Star washers (2)

Lock washers (2)

Spring washers (2)

B. Blade attachment hardware:

3/16”*6mm Screws(16)

Paper washers(16)

C. Blade holder attachment hardware:

1/4”*13.5mm screws with lock

washers(11)

Fan blades(5)

anger bracket

anopy

Canopy cover

Coupling cover

6. Standard downrod assembly(6")

Minimum-length downrod(3.5")

7. Fan motor/housing assembly

8. Light kit plate

9. Light kit assembly

10. 13W GU24 bulb(2)

1 1. Glass shade

12. Blade holder (5)

3 .

Receiver with 6 wire nuts

14 .Transmitter+holder+2 mouting

screws

15 .Balancing kit

INSTALLING THE FAN

MOUNTING OPTIONS

If there isn't an existing mounting box, then read the following instructions. Disconnect the

power by removing fuses or turning off circuit breakers.

Secure the outlet box directly to the building structure. Use appropriate fasteners and

building mateials. The outlet box and its support must be able to fully support the moving

weight of the fan (at least 50 lbs.).Use a UL listed metal outlet box. Do not use a plastic

outlet box.

Figure1,2 and 3 are examples of different ways to mount the outlet box.

Note: You may need a longer downrod to maintain proper blade clearance when installing on

a steep, sloped ceiling. Longer downrods are available from your Minka-Aire dealer.

To hang your fan where there is an existing fixture but no ceiling joist, you may need to

install a hanger bar as shown in Fig.4(available at your Minka Aire dealer or local hardware

store)

Tools Required: Philips screw driver, slotted screw driver,step-ladder, wire cutters,electrical tape.

FIG. 1

CROSS B RACE

CEILING

JOIST

CEILING

jOIST

OUTLET

BOX

FIG. 2

PARALL EL

WOOD BR AC E

(MIN. 2’’ THICK )

OUTLET

BOX

CEILING

JOIST OR

CROSS B RACE

FIG. 3

ANGLE D CEILI NG

MAXIM UM 20°ANG LE

PROVI DE

STRON G

SUPPO RT

RECES SED

OUTLE T

BOX

HANGE R

OPENI NG

must be

FACING

UPSIDE

FIG. 4

CEILING

JOIST

OUTLE T BOX

HANGE R BA R

(OPTI ONAL)

HANGE R

BRACKET

4 HANGING THE FAN

WARNING: All of the parts, hardware and components such as the

hanger bracket and hanger ball have been provided for your safety and

the proper installation of your new ceiling fan. The use of other

parts,hardware or components not supplied by Minka Aire with the fan

will void the Minka Aire Warranty.

REMEMBER to turn off the power. Follow the steps below to hang your

fan properly:

Stpe 2.Lossen the two set screws and remove the hitch pin and lock pin

from the top coupling of the motor assembly.(Fig 6)

Step 3.Remove hanger ball from downrod assembly by loosening set

screw,removing the cross pin, and sliding ball off rod.(Fig 7)

Step 1.Secure the hanger bracket to the ceiling outlet box using screws

and washers included with mounting hardware.(Fig.5)

Step 4.Carefully feed fan wires up through the downrod(Fig 8).

Thread the rod into the coupling, next line up holes and replace lock

pin and hitch pin. Tighten set screws.

NOTE:DO NOT INSTALL THE COUPLING COVER IF YOU PLAN TO USE

THE MINIMUM LENGTH DOWNROD.

Step 6. Now lift motor assembly into position and place hanger ball

into hanger bracket. Rotate until the check groove has dropped into

the registration slot and seats firmly.(Fig 10)Rod should not rotate

if this is done correctly.

Step5.Slip coupling cover, canopy cover, and canopy onto downrod

(Fig.9).Carefully reinstall hanger ball onto rod being sure that cross

pin is in the correct position, set screws are tighten and wires are

not twisted.

Fig. 10

REGISTRATION

SLOT

Fig. 8

DOWNROD

SUPPLY

WIRES

Fig. 7

CROSS PIN

HANGER

BALL

DOWNROD

SET SCREW

Fig. 6

HITCH

PIN LOCK

SET SCREWS

Fig. 5

OUTLET BOX

HANGER BRACKET

Fig. 9

LOCK PIN

CANOPY

COVER

DOWNROD

CANOPY

SET SCREWS

HITCH PIN

COUPLING

*OMIT COUPLING

COVER WHEN USING

DOWNROD

THE MINIMUM-LENGTH

5ELECTRICAL CONNECTIONS

WARNING:To avoid possible electrical shock be sure electricity

is turned off at the main fuse or breaker box before wiring.

NOTE: The Aire Control System is equipped with a learning frequency

function which has 256 code combinations to prevent potential

interference from other remote units.The frequency on your Receiver

and Transmitter units have been preset at the factory. (Fig.11) No

frequency change is necessary, should you desire to install another

fan whithin the same home or area with a separate frequency code

please see the ”frequency interference ”troubleshooting section

of this instruction manual to learn how to change the frequency.

Step 1. Insert Receiver into Hanger Bracket with the flat side of

the Receiver facing the ceiling.(Fig.12)

Step 2. Motor to Receiver Electrical Connections: Connect the WHITE

wire from the fan to the WHITE wire marked”TO MOTOR N” from

the Receiver. Connect the BLACK wire from the fan to the BLACK

wire marked”TO MOTOR L” from the Receiver. Connect the BLUE wire

from the fan to the BLUE wire marked”For Light” from the Receiver.

NOTE: If your ceiling fan features an UP Light: Connect the ORANGE

wire from the fan to the ORANGE wire marked “ For Up Light ” from

the Receiver. Otherwise disregard this step and proceed to secure all

wire connections with the plastic wire nuts provided.(Fig.13)

Note:Fan must be installed from a maximum distance of 40 feet from

the transmitting unit for proper signal transmission between the

transmitting unit and the fan’s receiving unit.

Step 3.Receiver to House Supply Wires Electrical connections:Connect

the WHITE wire(Neutral) from the outlet box to the WHITE wire

marked”AC in N” from the receiver. Connect the BLACK wire(Hot) from

the outlet box to the BLACK wire marked “AC in L” from the receiver.

Secure all wire connections with the plastic wire nuts provided.(Fig.13)

Step 4.If your outlet box has a GROUND wire (Green or Bare Copper)

connect this wire to the Hanger Ball and Hanger Bracket Ground wires.

If your outlet box does not have a Ground Wire, then connect the

Hanger Ball and Hanger Bracket Ground Wire together. Secure wire

connection with the plastic wire nut provided.(Fig. 13)

After all splices are made,check to make sure there are no loose strands.

As an additional precaution we suggest to secure the plastic wire

connectors to the wires with electrical tape.

Fig. 11

Fig. 12

RECEIVER

HANGER BRACKET

Fig. 13

WHITE (NEUTRAL)

GREEN OR BARE

COPPER (GROUND)

WHITE ( AC IN N )" "

WHITE ( TO MOTOR N )" "

GROUND-

(GREEN)

(CONNECT TO

GROUND WIRE ON

HANGER BRACKE

IF NO HOUSE

GROUND WIRE

EXISTS.)

OUTLET BOX

BLACK (HOT)

BLACK ( AC IN L )" "

BLACK ( TO MOTOR L )" "

RECEIVER

BLUE (FOR LIGHT)

ORANGE

(FOR UPPER LIGHT)

BLACK (MOTOR)

ORANGE

(FOR UPPER LIGHT)

FINISHING THE INSTALLATION

″

Step 1. Tuck connections neatly into ceiling outlet box.

Step 2. Remove one screw from the hanger bracket and loosen the other screw around 1/4” .

Step3. Align the canopy up to ceiling and over the loose screw. Place the canopy into key hole

and rotate canopy clockwise. (Figure 14)

Step 4. Secure the canopy by use previous removed screw.

Step 5. Place the canopy cover to the canopy and rotate canopy cover clockwise until it is

locked into right position.(Figure 14)

Fig. 14

OUTLET BOX

HANGER

BRACKET

HANGER

BALL

CANOPY

COVER

7BLADE INSTALLATION

Step1.

Attach the fan blades to the blade holders by using three

screws and paper washers as shown in Figure 15. Start a screw

into the blade holder, do not tighten. Repeat for the 2

remaining screws and washers. Tighten each screw securely

starting with the center screw (Fig. 15)

Step2.Remove the rubber stops from motor. Rotate the motor so

that the screw holes in motor are aligned with the holes in blade

holder and secure with proper screws. Repeat process for the other

blade holders.(Fig. 16)

Blade holder

SCREWS

PAPER

WASHERS

BLADE

Fig. 15

Blade holder

SCREWS

Fig. 16

Blade

holder

INSTALLING THE LIGHT KIT PLATE

Step1.Remove 1of 4screws from the mounting ring and loosen the other 3

screws.(Do not remove.)

Step2.Place the key holes from the light kit plate over the 3 screws previously

loosened from the mounting ring , turn light kit plate until it locks in place at the

narrow section of the key holes. Secure by tightening the 3 screws previously

loosened and the one previously removed.(Fig.17)

Fig. 17

Mounting ring

Light kit plate

NOTE: Before starting installation, disconnect the power by turning off the circuit

breaker or removing the fuse at fuse box.

Step1. Remove one of the three outer screws and loosen the other 2 from the light kit plate.(Fig.

18)

Step2. Connect WHITE(BLUE) wire from light kit plate to WHITE(BLACK) wire from light kit

assembly with the connector.(Fig.18)

Step3. Place the key holes from the light kit assembly over the 2 screws previously loosened

from the light kit plate , turn light kit assembly until it locks in place at the narrow section of the

key holes. Secure by tightening the 2 screws previously loosened and the one previously

removed.(Fig.18)

9INSTALLING THE LIGHT KIT ASSEMBLY

Light Kit Warranty

“This Ceiling fan Light Kit Fixture is covered by a Limited 2 year Warranty from the Manufacturer,

effective from the date of purchase. This fixture is warranted against defects in the quality of the

housing, trims, diffuser, shades, and electrical components. Fixture finishes and/or lamps (bulbs)

are expressly excluded from this warranty; refer to bulb manufacturer for lamp warranty.”

LIGHT KIT PLATE

LIGHT KIT ASSEMBLY

CONNECTOR

OUTER

SCREW

Fig. 18

INSTALLING THE GLASS SHADE & LIGHT BULBS

WARNING: Shut of the power supply before removing or replacing lamp. If you accidentally

come into contact, wipe thoroughly with a clean, lint-free,cotton cloth. Use light bulb in

accordance with the fans specification. TO REDUCE THE RISK OF FIRE DO NOT EXCEED MAXIMUM

WATTAGE RATING.

The color correlated Temperature (CCT) for replacing the enclosed lamp is (2700K).

The ballast in each of these models can be replaced by a qualified electrician without cutting of

wires and without damage to the housing, trim, decorative elements or carpentry to which the

fixture is attached. See installation steps for more detail.

ATTENTION: The Energy Policy Act of 2005 requires this fan to be equipped with a 190 watt

limiting device. If lamping execeeds 190 watts,the ceiling fan’s light kit will shut off automatically.

Step1. Install 2*13 GU24 CFL bulbs (included) into socket.(Fig.19)

Step2. Remove the rubber washer, metal washer, metal nut, metal cap and finial from the light kit

assembly. Place glass shade over the light kit stem, secure with the rubber washer, metal washer,

metal nut, metel cap and finial. Do not over tighten.(Fig.19)

BULBS

METAL NUT

METAL WASHER

RUBBER WASHER

METAL CAP

LIGHT KIT

ASSEMBLY

OPERATING THE REMOTE CONTROL/WALL

TRANSMITTER

Restore Power to Ceiling Fan.

A.Buttons:

These buttons are used to set the fan speeds as follows;

=Low Speed

=Medium Speed

=High Speed

B.Button:

This button turns the fan off.

C.Button:

Press and release the button to turn the light ON or OFF,

this fan's light will not dim.

D.OFF-ON Slide Button Wall Control Fans Only)(

This button turns the power Off and On to the Fan and

Light s).(

E.Button:Full Function Remote Control Units Only( )

This button is used to change the direction of the

rotation of the blades;forward for warm weather or

reverse for cool weather.

NOTE:If your Remote Control or Wall Control does not

have a " " button,Please look for a slide reverse switch

on the motor housing.

Remote Control only:Install a A23 12 volt battery (included) .To prevent damage to transmitter remove the battery if not used for long periods of time.

Table of contents