Minka-Aire contactor F547 User manual

The Minka-Aire
Minka-Aire
®warranty is for one (1) year from
thedateofpurchasefromanauthorized
Minka-Aire
Minka-Aire
®dealer. This warranty is only valid to
the original purchaser or user against all defects in
material and workmanship (light bulbs excluded) for
one (1) full year. Additionally, Minka-Aire
Minka-Aire
®warrants
the motor only for the lifetime of the Minka Aire
Minka Aire
®
ceiling fan (excluding wall controls and electrical
components), to the original purchaser or user.
* The warranty is voided with the use of any non-
Minka-Aire
Minka-Aire
®electrical devices, E.g., wall controls or electrical dimmer
switches, etc…
* The warranty is void once the original purchaser or user ceases to
own the fan or the fan is moved from its original point of installation.
* The warranty is void with the use of any hanger bracket (non-Minka
Aire or non-fan specific) other than the hanger bracket supplied &
installed with this specific fan.
To obtain warranty service during the warranty period, the purchaser
should return the fan with the sales receipt to the original place of
purchase. The authorized Minka-Aire
Minka-Aire
®dealer, at its sole discretion,
will either repair or replace the fan after verifying the legitimacy of the
warranty claim. Replacement is subject to availability of the same
model. If the model is unavailable it will be replaced by one of equal
value. This is a limited warranty; the original purchaser or user is
responsible for the cost of removal and reinstallation of repaired or
replacement product.
To obtain the name of the Minka-Aire
Minka-Aire
®authorized dealer nearest you
call the Minka-Aire
Minka-Aire
®customer care department at 1-800-307-3267, or
contact Minka-Aire
Minka-Aire
®through www.minkagroup.net and write to: “Ask
Mr. Minka” to answer any questions or if you require assistance.
Warranty Service Information
Date Purchased
Store Purchased
Model No. F547
Serial No.

8

Fig. 14
Fig. 15
Fig. 16
Step 1. Remove 1 of the 2 screws
from the bottom of the hanger
bracket and loosen the other one half
a turn from the screw head.
Step 2. Slide the canopy up towards
the hanger bracket and place the key
hole on the canopy over the screw on
the hanger bracket, turn canopy until
it locks in place at the narrow section
of the key holes. (Fig. 14)
Step 3. Align the circular hole on
canopy with the remaining hole on
the hanger bracket, secure by
tightening the two set screws.
Note:
Note:
Adjust the canopy screws as
necessary until the canopy are snug.
Step 1. Attach the fan blade to the
blade bracket using the screws
provided. Tighten screws securely.
Repeat for remaining blades. (Fig. 15)
Step 2. Remove the rubber stops
from the motor. Rotate the motor so
that the screw holes are revealed
through the opening on switch cup
plate. Align holes in blade bracket
and motor and secure with proper
screws. Repeat process with the other
blade bracket. Process with the other
blade brackets. (Fig. 16)
Note:
Note:
You have the option of
installing either five or four blades. If
youare using four blades, mount
blade bracket to the inner screw
holes. If youare using five blades,
mount blade bracket to the outer
screw holes. (Fig. 16)
6. FINISHING THE INSTALLATION
7. ATTACHING THE FAN BLADES
OUTLET BOX
HANGER
BRACKET
HANGER
BALL
CANOPY
FAN BLADE
BLADE HOLDER
SCREWS
FIBER
WASHERS
INNER
SCREW
HOLES
OUTER
SCREW
HOLES