MINN KOTA ULTERRA QUEST User manual

ULTERRA®QUESTTM
BOW-MOUNT TROLLING MOTOR
Installation Instructions

2 | minnkota.johnsonoutdoors.com ©2023 Johnson Outdoors Marine Electronics, Inc.
INTRODUCTION
EXAMPLE
THANK YOU
Thank you for choosing Minn Kota. We believe that you should spend more time fishing and less time positioning your boat. That’s why
we build the smartest, toughest, most intuitive trolling motors on the water. Every aspect of a Minn Kota trolling motor is thought out and
rethought until it’s good enough to bear our name. Countless hours of research and testing provide you the Minn Kota advantage that can
truly take you “Anywhere. Anytime.” We don’t believe in shortcuts. We are Minn Kota. And we are never done helping you catch more fish.
REGISTRATION
Remember to keep your receipt and immediately register your trolling
motor on our website at minnkota.johnsonoutdoors.com/us/register.
SERIAL NUMBER
Your Minn Kota 11-character serial number is very important. It helps
to determine the specific model and year of manufacture. When
contacting Consumer Service or registering your product, you will
need to know your product's serial number. A duplicate copy of your
serial number label has been included, which can also be entered in
the One-Boat Network App for future reference.
MOTOR INFORMATION (For Consumer Reference Only)
Made for
Android
Android
™
™
Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in
the badge, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this
device or its compliance with safety and regulatory standards. iPhone is a trademark of Apple Inc., registered in the U.S. and other countries.
The trademark “iPhone” is used in Japan with a license from Aiphone K.K.
AndroidTM is a trademark of Google LLC. The Android robot is reproduced or modified from work created and shared by Google and used
according to terms described in the Creative Commons 3.0 Attribution License.
Made for iPhone® 11 and iPhone X
For updated iOS, Humminbird® and Minn Kota® compatibility, visit minnkota.johnsonoutdoors.com
Model: ____________________________________________________________________________________________________
Serial Number: ______________________________________________________________________________________________
Purchase Date: ______________________________________________________________________________________________
Store Where Purchased: _______________________________________________________________________________________
NOTICE: The serial number for the Ulterra QUEST is located
on the inside of the Mount, behind the left Motor Ramp.
NOTICE: Do not return your Minn Kota motor to your retailer. Your retailer is not authorized to repair or replace this unit. You may
obtain service by: calling Minn Kota at [phone]; returning your motor to the Minn Kota Factory Service Center; sending
or taking your motor to any Minn Kota authorized service center. A list of authorized service centers is available on our website
at minnkota.johnsonoutdoors.com. Please include proof of purchase, serial number and purchase date for warranty service with
any of the above options.

minnkota.johnsonoutdoors.com | 3©2023 Johnson Outdoors Marine Electronics, Inc.
SAFETY CONSIDERATIONS
Please thoroughly read the user manual. Follow all instructions and heed all safety and cautionary notices. Use of this motor is only
permitted for persons that have read and understood these user instructions. Minors may use this motor only under adult supervision.
WARNING
You are responsible for the safe and prudent operation of your vessel. We have designed your Minn Kota product to be an accurate
and reliable tool that will enhance boat operation and improve your ability to catch fish. This product does not relieve you from the
responsibility for safe operation of your boat. You must avoid hazards to navigation and always maintain a permanent watch so you can
respond to situations as they develop. You must always be prepared to regain manual control of your boat. Learn to operate your Minn
Kota product in an area free from hazards and obstacles.
WARNING
Never run the motor out of the water, as this may result in injuries from the rotating propeller. The motor should be disconnected from
the power source when it is not in use or is o the water. When connecting the power-supply cables of the motor to the battery, ensure
that they are not kinked or subject to chafe and route them in such a way that persons cannot trip over them. Before using the motor
make sure that the insulation of the power cables is not damaged. Disregarding these safety precautions may result in electric shorts
of battery(s) and/or motor. Always disconnect motor from battery(s) before cleaning or checking the propeller. Avoid submerging the
complete motor as water may enter the lower unit through control head and shaft. If the motor is used while water is present in the lower
unit considerable damage to the motor can occur. This damage will not be covered by warranty.
WARNING
Take care that neither you nor other persons approach the turning propeller too closely, neither with body parts nor with objects. The
motor is powerful and may endanger or injure you or others. While the motor is running watch out for persons swimming and for floating
objects. Persons whose ability to run the motor or whose reactions are impaired by alcohol, drugs, medication, or other substances
are not permitted to use this motor. This motor is not suitable for use in strong currents. The constant noise pressure level of the motor
during use is less than 70dB(A). The overall vibration level does not exceed 2,5 m/sec2.
WARNING
It is recommended to only use Johnson Outdoors approved accessories with your Minn Kota motor. Using non-approved accessories
including to mount or control your motor may cause damage, unexpected motor operation and injury. Be sure to use the product and
approved accessories, including remotes, safely and in the manner directed to avoid accidental or unexpected motor operation. Keep all
factory installed parts in place including motor and accessory covers, enclosures and guards.
WARNING
When stowing or deploying the motor, keep fingers clear of all hinge and pivot points and all moving parts. In the event of unexpected
operation, remove power leads from the battery.

4 | minnkota.johnsonoutdoors.com ©2023 Johnson Outdoors Marine Electronics, Inc.
KNOW YOUR BOAT
KeelKeel
BowBow
HullHull
BowBow
SternStern
SternStern
PortPort
PortPort StarboardStarboard
StarboardStarboard
GunwaleGunwale
GunwaleGunwale
InboardInboard
OutboardOutboard
TransomTransom

minnkota.johnsonoutdoors.com | 5©2023 Johnson Outdoors Marine Electronics, Inc.
INSTALLATION
INSTALLING THE ULTERRA QUEST
Your new Ulterra QUEST comes with everything you’ll need to install it directly to the boat. The motor can be mounted directly to the
bow or coupled with a Minn Kota quick release bracket for ease of mounting and removal. For compatible quick release brackets and to
locate your nearest dealer, visit minnkota.johnsonoutdoors.com. To install the motor directly to the boat, follow the instructions provided
in this manual. Please review the parts list, mounting considerations and tools needed for installation prior to getting started. For
additional product support, visit minnkota.johnsonoutdoors.com.
INSTALLATION PARTS LIST
Item /
Assembly Part # Description Qty.
A
(Includes 1-5) 2994948 BAG ASM, INSTINCT, T3 BL HDW 1
1 2323440 SCREW-3/8-16 X 2 1/2 HHCS SS 6
2 2383122 NUT 3/8-16 NYLON INST LOCKNUT 6
3 2321710 WASHER, RUBBER MOUNT 6
4 2371796 BACKUP BAR 3/16 X 1 X 2 6
5 2378608 ANTI SEIZE TUBE, 4CC, TALON 1
6✖MOTOR ASSEMBLY 1
7 2390802 LANYARD w/CARARBINER IP RMT U2 1
8 411690-1 TROLLING MOTOR REMOTE 1
9 2992371 STABILIZER, BWMT ES TM ASM *72"* 1
10 2321170 PROP, POWER REAMED 1
B
(Includes 11-13) 2992604 BAG ASSM, PROP HARDWARE 1
11 2091701 WASHER-PROP (LARGE) MAX101 1
12 2093101 NUT-PROP,NYLOC,LG,MX101 3/8 SS 1
13 2262659 PIN-DRIVE 1" X 3/16 SS 17-4 1
C 2994742 FT PED ASM, ULTERRA QUEST 1
D
(Includes 14) 2994859 BAG ASY-TERROVA/V2,RUB.BUMPERS 1
14 2325110 PAD,FOOT PEDAL PD 5
15 490637-4 CABLE, ETH, M12-M12, BRAID,30' 1
16 490380-1 CABLE, ETHERNET PIGTAIL-700 HD 1
17 2206301 TIE WRAP, LOW PROFILE 8" 1
18 2994961 BAG ASM, CABLE,ADPTR, 490537-2
*490537-2* *MKR-MI-1* *DSC* *MSI* 1
E
(Includes 19) 2994955 BAG ASM, MKA-60 STABILIZER *72”* 1
19 2383475 SCREW-#8-18x1½L SELF DRILL SS *72”* 4
p2207124 MANUAL, ULTERRA 1
p2207125 MANUAL, INSTL GD, ULTERRA 1
p2207126 QK REF GUIDE,ULT Q/INST Q 1
p2397110 MANUAL, WIRELESS REMOTE 1
p2397115 GUIDE-QCK REFERENCE iP 4.0 1
p2294950 INSTRUCTIONS,OBN & REMOTE PAIR 1
p2207130 BRUSHLESS QS SETUP GUIDE 1
p2377179 INSTR.SHEET, MKA-60 STBLZR *72"* 1
pNot shown on Parts Diagram.
✖This part is included in an assembly and cannot be ordered individually.
44
33
DD
66
22
11
AA1313
55
1414
1111
1818
1616
1515
88
1717
77
1212
1010
BB
CC
99
1919
EE

6 | minnkota.johnsonoutdoors.com ©2023 Johnson Outdoors Marine Electronics, Inc.
MOUNTING CONSIDERATIONS
All six mounting holes must be used when securing the Ulterra QUEST to the boat deck. If the desired mounting location does not allow for
all six mounting holes and mounting bolts, a Boat Deck Reinforcement Kit (1854058) should be used or a new mounting location selected.
Consider a quick release bracket with the installation of your motor.
Mounting options for the Ulterra QUEST include:
1. Installing the motor directly to the boat deck
2. Mounting the motor with an MKA-58 Boat Deck Reinforcement Kit (1854058)
3. Mounting the motor with an MKA-56/RTA-55 composite quick release bracket (1854056 - black/1854055 - white) or an MKA-57
sliding quick release bracket (1854057)
4. Combining an MKA-58 Boat Deck Reinforcement Kit and an MKA-56/RTA-55 Quick Release Bracket with the Ulterra QUEST
When mounting the Ulterra QUEST directly to the boat, follow the installation instructions outlined in this manual. If an accessory
bracket will be used to mount the Ulterra QUEST, follow the installation instructions provided with the mounting accessory. To view a list
of compatible accessories, visit minnkota.johnsonoutdoors.com.
It is recommended that the motor be mounted as close to the centerline or keel of the boat
as possible. Make sure the area under the mounting location is clear to drill holes and install
hardware. The mounting surface for the Ulterra QUEST must be flat. Rubber washers can be
used to shim the base extrusion flat before hardware is tightened.
The motor must not encounter any obstructions as it is lowered into the water or raised into the
boat when stowed and deployed. When stowed, ensure that there is enough room for the Shaft
and Control Head and that they do not extend off the side of the boat.
MOUNTING CONSIDERATIONS
View accessories
available for your
trolling motor
at minnkota.
johnsonoutdoors.com.
1 2 3 4
• #3 Phillips Screwdriver
• Drill
• 3/8” Drill Bit
• Awl or similar marking tool
• 9/16” Open/Box End Wrench
• 9/16" Deep Well Socket
• A second person to help with
the installation
TOOLS AND RESOURCES REQUIRED

minnkota.johnsonoutdoors.com | 7©2023 Johnson Outdoors Marine Electronics, Inc.
INSTALLING THE ULTERRA QUEST
INSTALLATION
Power CablesPower Cables
DeployedDeployed StowedStowed
2
SideplateSideplate
ScrewScrew
SideplateSideplate
Mounting HolesMounting Holes
c. Remove the four Sideplate Screws using a #3 Phillips
Screwdriver. Two of these screws will be located on
each side of the mount.
d. Remove the Right Sideplate and the Left Sideplate to
expose the six mounting holes in the Base Extrusion.
NOTICE: The trolling motor weighs up to 90lb.
Minn Kota recommends having a second person help
with the installation.
a. Place the trolling motor (Item #6) on an elevated,
level surface, such as a workbench or the tailgate
of a pickup. The motor, as removed from the box,
should be in the stowed position.
b. Make sure that the Power Cables from the battery
are disconnected or that the breaker, if equipped,
is “o.”
1
WARNING
Make sure the motor is on a level surface and is not
connected to a power source.
ITEM(S) NEEDED
#6 x 1
1a
1b
INSTALLING THE ULTERRA QUEST

8 | minnkota.johnsonoutdoors.com ©2023 Johnson Outdoors Marine Electronics, Inc.
INSTALLING THE ULTERRA QUEST
e. Review the mounting considerations at the beginning
of the Installation section for proper clearance. Place
the motor on the bow of the boat at the intended
mounting location, as close to the centerline or keel
as possible. Ensure there is enough room for the
Shaft and Control Head and that they do not extend
o the side of the boat. The motor can be installed
on either the Port or Starboard side of the bow,
based on personal preference.
f. Position the motor so that the Slot in the Base
Extrusion is positioned beyond the boat Gunwale.
For proper clearance, the entire Slot must be visible
beyond the Gunwale. When the motor is deployed,
there must be a minimum required distance of 1½"
between the Gunwale and the bottom of the Steering
Housing and Shaft.
GunwaleGunwale
SlotSlot
BowBow
KeelKeel
3OutboardOutboard
InboardInboard
StarboardStarboard
PortPort
3e
3f
Drilling LocationsDrilling Locations
Drilling LocationsDrilling Locations Base ExtrusionBase Extrusion
OutboardOutboard
4h. With the motor at the intended mounting location,
take an Awl or similar tool and mark all six mounting
holes in the Base Extrusion.
i. Slide the motor aside to drill the mounting holes.
Drill through the boat deck using a Drill and a 3/8”
Drill Bit on all six marked locations.
j. Reposition the motor over the drilled holes to install
mounting hardware.
NOTICE: New mounting holes are required when
upgrading from an Ulterra to an Ulterra QUEST. New
mounting holes will accommodate the higher thrust
motor and ensure the installation is secure.
NOTICE: The mounting surface for the Ulterra QUEST
must be flat. Rubber Washers can be used to shim the
Base Extrusion flat before hardware is tightened.
1½"1½"
MinimumMinimum
GunwaleGunwale
ShaftShaft
SteeringSteering
HousingHousing
3f
g. When mounting the Ulterra QUEST, all six mounting
holes must be used. If the desired mounting location
does not allow for all six mounting holes, a Boat
Deck Reinforcement Kit (1854058) should be used
or a new mounting location selected.
4h
CAUTION
Illustrations are for reference only. Do not deploy the motor
until it is fully mounted to the boat. Deploying the motor
before it is mounted to the boat may cause injury.

minnkota.johnsonoutdoors.com | 9©2023 Johnson Outdoors Marine Electronics, Inc.
INSTALLING THE ULTERRA QUEST
5ITEM(S) NEEDED
#1 x 6 #2 x 6 #3 x 6 #4 x 6 #5 x 1
Hex HeadHex Head
Cap ScrewCap Screw
Hex HeadHex Head
Cap ScrewCap Screw
RubberRubber
WasherWasher
BaseExtrusionBase Extrusion
Boat DeckBoat Deck
Backup BarBackup Bar
Nylock NutNylock Nut
k. Take six Hex Head Cap Screws (Item #1) and apply
anti-seize (Item #5) to each Screw. Insert the Screws
through the Base Extrusion and into each of the
drilled locations. If Rubber Washers (Item #3) are
used, the Rubber Washers should sit between the
Base Extrusion and boat deck.
l. Place a Backup Bar (Item #4) and then a Nylock Nut
(Item #2) on the end of each Screw. Tighten with a
9/16" Box End or Open End Wrench. Make sure all
hardware is secure.
NOTICE: To prevent seizing of the stainless steel
hardware, do not use high-speed installation tools.
Wetting the screws or applying an anti-seize (Item #5)
may help prevent seizing.
NOTICE: Use extra care to avoid pinching and
damaging the sensor wires that run alongside the
Base Extrusion when installing and tightening the
mounting hardware.
66m
SideplateSideplate
ScrewScrew
SideplateSideplate
m. Replace the Right Sideplate and Left Sideplate.
Replace the four Sideplate Screws using a #3 Phillips
Screwdriver. Two of these screws will be located on
each side of the mount.
NOTICE: When reinstalling the Sideplates, use care to
avoid pinching the sensor wires that run alongside the
Base Extrusion.
NOTICE: Ensure that the area between the Mount
and Steering Housing is clean and free of debris
and that no installation hardware has fallen in. The
Mount contains a Stow Pad that contacts the Steering
Housing when stowed. The motor cannot stow
securely if an obstruction is present on the Stow Pad.

10 | minnkota.johnsonoutdoors.com ©2023 Johnson Outdoors Marine Electronics, Inc.
BATTERY & WIRING INSTALLATION
BOAT RIGGING & PRODUCT INSTALLATION
For safety and compliance reasons, we recommend that you follow American Boat and Yacht Council (ABYC) standards when rigging
your boat. Altering boat wiring should be completed by a qualified marine technician. The following specifications are for general
guidelines only:
CONDUCTOR GAUGE AND CIRCUIT BREAKER SIZING TABLE
This conductor and circuit breaker sizing table is only valid for the following assumptions:
1. No more than 2 conductors are bundled together inside of a sheath or conduit outside of engine spaces.
2. Each conductor has 105° C temp rated insulation.
3. No more than 3% voltage drop allowed at full motor power based on published product power requirements.
CAUTION
These guidelines apply to general rigging to support your Minn Kota motor. Powering multiple motors or additional electrical devices
from the same power circuit may impact the recommended conductor gauge and circuit breaker size. If you are using wire longer than
that provided with your unit, follow the conductor gauge and circuit breaker sizing table below. If your wire extension length is more than
25 feet, we recommend that you contact a qualified marine technician.
CAUTION
An over-current protection device (circuit breaker or fuse) must be used. Coast Guard requirements dictate that each ungrounded
current-carrying conductor must be protected by a manually reset, trip-free circuit breaker or fuse. The type (voltage and current rating)
of the fuse or circuit breaker must be sized accordingly to the trolling motor used. The table below gives recommended guidelines for
circuit breaker sizing.
Motor Thrust /
Model
Max
Amp Draw
Circuit Breaker Wire Extension Length
Amps Minimum 5 feet 10 feet 15 feet 20 feet 25 feet
QUEST 24V 60 60 Amp 24 VDC 6 AWG 6 AWG 4 AWG 4 AWG 2 AWG
QUEST 36V 60 60 Amp 36 VDC 6 AWG 6 AWG 6 AWG 6 AWG 4 AWG
Reference
United States Code of Federal Regulations: 33 CFR 183 – Boats and Associated Equipment ABYC E-11: AC and DC Electrical Systems on Boats
NOTICE: Wire Extension Length refers to the distance from the batteries to the trolling motor leads. Consult website for available
thrust options.

minnkota.johnsonoutdoors.com | 11©2023 Johnson Outdoors Marine Electronics, Inc.
SELECTING THE CORRECT BATTERIES
SELECTING THE CORRECT BATTERIES
QUEST series motors will operate with any deep cycle marine 12, 24 or 36-volt battery/batteries and have been optimized for use with
LiFePO lithium-ion battery cells. Lithium-ion batteries maintain higher voltages for more extended periods than lead-acid batteries and
will provide the best performance in powering the trolling motor.
QUEST series trolling motors may also be powered with lead-
acid (flooded, AGM, or GEL) deep-cycle marine 12-volt battery/
batteries. For best results, Minn Kota recommends using a
deep-cycle marine battery with rating outlined in the "Deep Cycle
Amp-Hour Rating" table. Maintain lead-acid batteries at full
charge. Proper care will ensure battery power when needed and
significantly improve battery life. Failure to recharge lead-acid batteries (within 12-24 hours) is the leading cause of premature battery
failure. Use a multi-stage charger to avoid overcharging. When using Lithium Ion batteries, manufacturers may recommend storing in a
semi-charged state and charging fully prior to use.
If using a crank battery to start a gasoline outboard, Minn Kota recommends using a separate battery/batteries for your Minn Kota
trolling motor. Always check with the battery manufacturer for specific maintenance, care and storage instructions. Minn Kota also
oers a wide selection of chargers to fit your charging needs. For more information on battery selection, rigging, and chargers, please
visit minnkota.johnsonoutdoors.com.
Using DC or Alternator Chargers
Your Minn Kota trolling motor may be designed with an internal bonding wire to reduce sonar interference. Most alternator charging
systems do not account for this bonding wire, and connect the negative posts of the trolling motor batteries to the negative posts of
the crank/starting battery. These external connections can damage connected electronics and the electrical system of your trolling
motor, voiding your warranty. Review your charger’s manual carefully or consult the manufacturer prior to use to ensure your charger
is compatible.
Minn Kota recommends using Minn Kota brand chargers to recharge the batteries connected to your Minn Kota trolling motor,
as they have been engineered to work with motors that include a bonding wire. Learn more about Minn Kota chargers online at
minnkota.johnsonoutdoors.com.
ADDITIONAL CONSIDERATIONS
WARNING
Never connect the (+) and the (–) terminals of the same battery together. Take care that no metal object can fall onto the battery and
short the terminals. This would immediately lead to a short and extreme fire danger.
CAUTION
Refer to “Conductor Gauge and Circuit Breaker Sizing Table” in the previous section to find the appropriate circuit breaker or fuse for
your motor. For motors requiring a 60-amp breaker, the Minn Kota MKR-27 60-amp circuit breaker (1865115) is recommended.
CAUTION
Please read the following information before connecting your motor to your batteries in order to avoid damaging your motor and/or
voiding your warranty.
Deep Cycle Amp-Hour Rating
Run Time Voltage Group Size Amp-Hour
GOOD 12 24 70-85
BETTER 12 27 85-110
BEST 12 31 95-125

12 | minnkota.johnsonoutdoors.com ©2023 Johnson Outdoors Marine Electronics, Inc.
CONNECTING THE BATTERIES IN SERIES
Automatic jump start systems and selector switches tie the negatives of the connected batteries together. Connecting these systems
to the “High Side” Battery or “Middle” Battery in the diagrams below and will cause significant damage to your trolling motor and
electronics. The only trolling motor battery that is safe to connect to one of these systems is the “Low Side” Battery.
The negative (-) connection must be connected to the negative terminal of the same battery that the trolling motor negative lead
connects to. In the diagrams below this battery is labeled “Low Side” Battery. Connecting to any other trolling motor battery will input
positive voltage into the “ground” of that accessory, which can cause excess corrosion. Any damage caused by incorrect connections
between battery systems will not be covered under warranty.
Automatic Jump Start Systems and Selector Switches
CONNECTING THE BATTERIES IN SERIES
(IF REQUIRED FOR YOUR MOTOR)
24-Volt Systems
Two 12-volt batteries are required. The batteries must be wired in
series, only as directed in the wiring diagram, to provide 24 volts.
1. Make sure that the motor is switched o (speed selector on “0”).
2. Connect a connector cable to the positive ( + ) terminal of
battery 1 and to the negative ( – ) terminal of battery 2.
3. Connect positive ( + ) red motor lead to positive ( + ) terminal
on battery 2.
4. Connect negative ( – ) black motor lead to negative ( – ) terminal
of battery 1.
To trolling motor negative
24 Volt Series Connection
Battery #1
(Low Side)
Neg - Neg -Pos + Pos +
Battery #2
(High Side)
+24 Volts to trolling motor
positive (or circuit breaker)
Two 12-volt batteries connected in series for 24 volts
WARNING
For safety reasons do not switch the motor on until the propeller is in the water. If installing a leadwire plug, observe proper polarity and
follow instructions in your boat owner’s manual.
WARNING
• For safety reasons, disconnect the motor from the battery or batteries when the motor is not in use or while the battery/batteries
are being charged.
• Improper wiring of 24/36 volt systems could cause battery explosion.
• Keep leadwire wing nut connections tight and solid to battery terminals.
• Locate battery in a ventilated compartment.
Additional Accessories Connected to Trolling Motor Batteries
Significant damage to your Minn Kota motor, your boat electronics, and your boat can occur if incorrect connections are made between
your trolling motor batteries and other battery systems. Minn Kota recommends using an exclusive battery system for your trolling motor.
Where possible, accessories should be connected to a separate battery system. Radios and sonar units should not be connected to any
trolling motor battery systems as interference from the trolling motor is unavoidable. If connecting any additional accessories to any
trolling motor battery system, or making connections between the trolling motor batteries and other battery systems on the boat, be sure
to carefully observe the information below.

minnkota.johnsonoutdoors.com | 13©2023 Johnson Outdoors Marine Electronics, Inc.
CONNECTING THE BATTERIES IN SERIES
36-Volt Systems
Three 12-volt batteries are required. The batteries must be wired in series, only as directed in the wiring diagram, to provide 36 volts.
1. Make sure that the motor is switched
o (speed selector on “0”).
2. Connect a connector cable to the
positive ( + ) terminal of battery 1 and
to the negative ( – ) terminal of battery 2
and another connector cable from the positive
( + ) terminal of battery 2 to the negative ( – )
terminal of battery of battery 3.
3. Connect positive ( + ) red motor lead
to positive ( + ) terminal on battery 3.
4. Connect negative ( – ) black motor lead to
negative ( – ) terminal of battery 1.
To trolling motor negative
24 Volt Series Connection 36 Volt Series Connection
Battery #1 (Low Side)
Neg - Neg - Neg -Pos + Pos + Pos +
Battery #2 (Middle) Battery #3 (High Side)
+36 Volts to trolling motor
positive (or circuit breaker)
Three 12-volt batteries connected in series for 36 volts
WARNING
• For safety reasons, disconnect the motor from the battery or batteries when the motor is not in use or while the battery/batteries
are being charged.
• Improper wiring of 24/36 volt systems could cause battery explosion.
• Keep leadwire wing nut connections tight and solid to battery terminals.
• Locate battery in a ventilated compartment.
WARNING
For safety reasons, do not switch the motor on until the propeller is in the water. If installing a leadwire plug, observe proper polarity and
follow instructions in your boat owner’s manual.

14 | minnkota.johnsonoutdoors.com ©2023 Johnson Outdoors Marine Electronics, Inc.
COMPLETING THE INSTALLATION
COMPLETING THE ULTERRA QUEST INSTALLATION
The Ulterra QUEST is an advanced trolling motor. To maximize its performance, mechanical and electrical systems should be set and
calibrated to fit every user's installation. This portion of the installation will cover how to verify power, install the Bow-mount Stabilizer,
and more. The installation will conclude with connecting Accessory Cables and setting motor preferences for ease of use. Minn Kota
recommends connecting the trolling motor to the One-Boat Network app to assist in these steps. Find more information in the
One-Boat Network App document included with the trolling motor or the One-Boat Network Owner’s Manual found online at
minnkota.johnsonoutdoors.com.
Verifying Power
Each time the trolling motor is powered "on," the control board will auto-detect the power supplied from the battery system and adjust
the thrust output based on a 24V or 36V battery system. To verify power to the trolling motor, connect the Ulterra QUEST to power. At
specific points in the installation, power will be disconnected or turned "o" to ensure a safe environment for installation.
COMPLETING THE INSTALLATION
1a. Locate the Indicator Panel at the front of the Mount.
Power on the trolling motor by pressing the Power
button on the Indicator Panel. When the trolling
motor is on, the System Status SYSTEM
STATUS LED will be blue.
b. To turn the motor "o," press and release the Power
button. When the Motor is powered o, the System
Status SYSTEM
STATUS LED will not be illuminated.
SYSTEM STATUS
SYSTEM STATUS
SYSTEM STATUS
ULTERRA
SystemSystem
StatusStatus
LEDLED
Indicator PanelIndicator Panel
PowerPower
ButtonButton
Installing the Bow-Mount Stabilizer
Ulterra QUEST motors with a 72" shaft length come with an MKA-60 Bow-Mount Stabilizer Kit (Item #9 and Assembly #E). This
accessory stabilizes the shaft and control head when the motor is stowed for transport. Motors with shaft lengths under 72" may
purchase the MKA-60 separately as an optional accessory (1862060). For instructions on installing the MKA-60 to the Ulterra QUEST,
refer to the document provided with the Bow-Mount Stabilizer Kit.
NOTICE: In instances where the trolling motor is updating, the System Status LED will flash blue while the update is
performed. Once the update is complete, the system will self-reboot and perform the normal start-up sequence. If a standard
power-up sequence is not experienced, please see the Troubleshooting section of the Ulterra QUEST Owner’s Manual to
identify any errors. To learn more about software updates, please see the Owner’s Manual for the One-Boat Network or
Advanced GPS Navigation Wireless Remote.

minnkota.johnsonoutdoors.com | 15©2023 Johnson Outdoors Marine Electronics, Inc.
POWERING ON THE WIRELESS REMOTE
Powering on the Wireless Remote
1
a. Power on the trolling motor.
b. To turn on the Wireless Remote (Item #8), press and
hold the Power button on the side of the Remote.
c. A message will appear on the display screen. Read
the disclaimer, then press the Steer Right button
to select "I Agree."
d. The content on the display screen will populate.
Remote functions to manually control the motor are
now active, including Speed Up , Speed Down
, Steer Left , Steer Right , and Prop On/O.
e. When the Advanced GPS Navigation system has
obtained a minimum GPS signal strength of one bar,
all remaining functions will become available.
PowerPower
ButtonButton
NOTICE: The Wireless Remote comes from the factory
paired to the Ulterra QUEST.
NOTICE: A Remote Cradle accessory (1866675) can
be purchased for mounting the Wireless Remote or
attaching the Remote to a belt clip.
NOTICE: Attaching the Lanyard (Item #7) to the
Wireless Remote is optional.
ITEM(S) NEEDED
#8 x 1
WirelessWireless
RemoteRemote
#7 x 1

16 | minnkota.johnsonoutdoors.com ©2023 Johnson Outdoors Marine Electronics, Inc.
INSTALLING THE FOOT PEDAL
Installing the Foot Pedal
NOTICE: Adding the Foot Pedal pads is optional.
The pads are recommended when using the Foot
Pedal on non-carpeted surfaces.
Foot PedalFoot Pedal
BottomBottom
Foot PedalFoot Pedal
Pad PlacementPad Placement
ITEM(S) NEEDED
#14 x 4 #C x 1
a. Take the Foot Pedal (Item #C) and turn it over.
Put a Foot Pedal Pad (Item #14) in each of the
pad locations.
1
b. Locate the Foot Pedal Power Cord that exits the
Mount of the trolling motor, next to the Power
Cables. Unscrew the Cap on the Plug at the end of
the Foot Pedal Power Cord.
c. Locate the 4-Pin Plug from the Foot Pedal and
unscrew the Cap.
d. Align the 4-Pin Plug from the Foot Pedal with the
Plug from the trolling motor. Firmly push the Plugs
together. Secure the connection by rotating
the collar on the Foot Pedal Power Cord in a
clockwise direction.
NOTICE: The connectors are keyed to prevent
reversed installation.
NOTICE: When the Foot Pedal Power Cord is not in
use, ensure that the Cap is on and firmly secured.
2
2c 4-Pin Plug from4-Pin Plug from
Foot PedalFoot Pedal
PlugPlug
CapCap
2d Foot Pedal Power CordFoot Pedal Power Cord
from Trolling Motorfrom Trolling Motor
4-Pin Plug from4-Pin Plug from
Foot PedalFoot Pedal
2b
Foot PedalFoot Pedal
Power Cord fromPower Cord from
Trolling MotorTrolling Motor
Power CablesPower Cables

minnkota.johnsonoutdoors.com | 17©2023 Johnson Outdoors Marine Electronics, Inc.
IDENTIFYING TROLLING MOTOR FEATURES AND THEIR ASSOCIATED CABLES
Identifying Connectors
Two connectors are present below the Control Head. The trolling
motor will be equipped with:
Advanced GPS Navigation & Dual Spectrum CHIRP or Built-in
MEGA Side Imaging - Advanced GPS Navigation is pre-installed
on your trolling motor. One Eight-Pin Advanced GPS Ethernet
Connector will exit the base of the Control Head and rest just
below the Control Head next to the Coil Cord. If the Advanced
GPS Navigation on the trolling motor will be used with a fish
finder, an Ethernet Cable may be attached to the Advanced GPS
Ethernet Connector below the Control Head. See the “Advanced
GPS Navigation” section of this document for details on how to
install the Advanced GPS Ethernet Connector to a Humminbird.
Dual Spectrum CHIRP or Built-in MEGA Side Imaging is also
pre-installed on your trolling motor. One Sonar Accessory Cable
will exit the base of the Control Head and run down the center
of the Coil Cord. The end of this Cable has a Fourteen-Pin
Connector. Motors with Dual Spectrum CHIRP or Built-in MEGA
Side Imaging will also have a transducer in the Lower Unit. The
appearance of the transducer will vary depending on sonar type.
Dual Spectrum CHIRP Built-in MEGA Side Imaging
Control HeadControl Head
MountMount
AdvancedAdvanced
GPSGPS
EthernetEthernet
ConnectorConnector
Built-in MEGA SideBuilt-in MEGA Side
Imaging or DualImaging or Dual
Spectrum CHIRPSpectrum CHIRP
Fourteen-PinFourteen-Pin
ConnectorConnector
Eight-PinEight-Pin
ConnectorConnector
Advanced GPSAdvanced GPS
Ethernet ConnectorEthernet Connector
Coil CordCoil Cord
IDENTIFYING TROLLING MOTOR FEATURES AND THEIR ASSOCIATED CABLES
Feature & Cable Identification
The Ulterra QUEST is pre-installed with Advanced GPS Navigation - including the ability to connect via Ethernet to a Humminbird unit.
The motor is also pre-installed with sonar, either Dual Spectrum CHIRP or Built-in MEGA Side Imaging. These features may be installed
on their own or in combination with another feature. All of these features require Accessory Cables to be connected to an output device.
The connectors are present on the trolling motor and have cables that exit below the Control Head. To better identify Accessory Cables
present, refer to the diagrams that detail what the Dual Spectrum CHIRP, Built-in MEGA Side Imaging and Advanced GPS Navigation
connectors look like.
Ethernet CableEthernet Cable
from Trolling Motorfrom Trolling Motor
ThreadedThreaded
CollarCollar
LockingLocking
CollarCollar
Eight-PinEight-Pin
ConnectorConnector
Dual Spectrum CHIRPDual Spectrum CHIRP
from Trolling Motorfrom Trolling Motor
Dual Spectrum CHIRP Advanced GPS Navigation
Fourteen-PinFourteen-Pin
ConnectorConnector
LockingLocking
CollarCollar
Built-in MEGABuilt-in MEGA
Side Imaging fromSide Imaging from
Trolling MotorTrolling Motor
Built-in MEGA Side Imaging
Fourteen-PinFourteen-Pin
ConnectorConnector

18 | minnkota.johnsonoutdoors.com ©2023 Johnson Outdoors Marine Electronics, Inc.
DUAL SPECTRUM CHIRP
Feature & Cable Management
Your trolling motor may be pre-installed with a transducer system
featuring Humminbird’s Dual Spectrum CHIRP. CHIRP stands
for “Compressed High Intensity Radar Pulse.” Dual Spectrum
CHIRP is a 2D sonar transducer with a temperature sensor that
is integrated into the lower unit of the trolling motor. Humminbird
also utilizes a proprietary, best-in-class transducer designed
and built to maximize fish detail, as well as coverage area. Dual
Spectrum CHIRP scans the water for fish similar to the way the
seek function on your truck’s radio scans the airwaves for
FM stations. By covering a wide range of frequencies, CHIRP
produces more accurate, more detailed returns of fish, structure,
and the bottom.
Humminbird’s Dual Spectrum CHIRP gives you full spectrum
capability, plus the power to select your own start and end
frequencies by operating in two dierent modes. Wide Mode for
maximum coverage and Narrow Mode for maximum detail. Wide
mode allows you to search deep and wide. Is it used for watching
your lure while vertical jigging, or gaining a more expansive view
in shallow water. Narrow Mode is used to hone in on the small
stu that makes a big dierence. Narrow Mode provides a precise
perspective of the water below, helping you target individual fish,
or identify fish hidden in structure and/or tight to the bottom.
DUAL SPECTRUM CHIRP
Wide Mode
Target Separation
Narrow Mode
Defined Fish Arches Strong Returns
Dual Spectrum CHIRP features:
SUPERIOR TARGET SEPARATION - Separating fish from their habitat is the name of the game. And now, you’ll be able to tell the
dierence more easily between bait and game fish, and nearby structure and vegetation.
CLEARLY DEFINED FISH ARCHES - We’ve got bad news for your arch nemesis. Large game fish will show up on your screen as long,
well-defined arches, for quick identification and accurate lure presentation.
STRONG RETURNS WITHOUT NOISE - Stop seeing things that aren’t there. A high signal-to-noise ratio translates to better defined
targets, less clutter and greater certainty that what you’re looking at on-screen is legit.
Dual Spectrum CHIRP Lower Unit

minnkota.johnsonoutdoors.com | 19©2023 Johnson Outdoors Marine Electronics, Inc.
DUAL SPECTRUM CHIRP
Considerations for Connecting and Routing Dual Spectrum CHIRP
If Dual Spectrum CHIRP is pre-installed on your trolling motor, one Dual Spectrum CHIRP accessory cable will exit the base of the
Control Head and run down the center of the Coil Cord. Dual Spectrum CHIRP requires cables to be connected to an output device
such as a Humminbird® fish finder. The Dual Spectrum CHIRP cable that exits the Control Head is "Apex and Solix Ready." Connecting
the trolling motor equipped with a Dual Spectrum CHIRP transducer to a compatible fish finder gives you a 2D sonar view of what is
happening directly below your trolling motor. To determine if your fish finder is compatible with Dual Spectrum CHIRP, please visit
minnkota.johnsonoutdoors.com to check compatibility. The Dual Spectrum CHIRP cable from the trolling motor may be plugged directly
into a Solix or Apex, directly into an Extension Cable or directly into a Humminbird® Helix Adapter Cable.
EXTENSION CABLES - The Dual Spectrum CHIRP cable from the trolling motor may not be long enough to reach your fish finder. If the
cable length does not reach the desired fish finder installation location, extension cables are available. A 10-foot extension cable
(EC M3 14W10 - 10' transducer extension cable - 720106-1) and a 30-foot extension cable (EC M3 14W30 - 30' transducer extension
cable - 720106-2) are available from humminbird.johnsonoutdoors.com. Both the 10-foot and 30-foot extension cables also come "Apex
and Solix Ready." The Extension Cables may plug directly into a Solix or Apex or directly into a Helix Adapter Cable.
HUMMINBIRD HELIX ADAPTER CABLES - If connecting to a Humminbird® Helix fish finder, an adapter cable accessory is included
that will allow the connection of any compatible Humminbird® Helix fish finder. The Helix adapter cables will plug directly into the Helix
fish finder.
OTHER FISH FINDER ADAPTER CABLES - If connecting to other fish finders on the market, check for compatibility or any required
adapter cables online at minnkota.johnsonoutdoors.com.
The integrated design of the Dual Spectrum CHIRP transducer protects it in the lower unit of the trolling motor from underwater hazards
and prevents tangles and damage to the transducer cables. In certain situations, air bubbles may adhere to the surface of the Dual
Spectrum CHIRP transducer and aect the performance. If this happens, simply wipe the surface of the transducer with your finger.
Control HeadControl Head
MountMount
Dual SpectrumDual Spectrum
CHIRPCHIRP
ExtensionExtension
CableCable
(if needed)(if needed)
CoilCoil
CordCord
Dual Spectrum CHIRP Connections
Foot PedalFoot Pedal
Power ConnectorPower Connector Power CablesPower Cables
DirectlyDirectly
to Solixto Solix
or Apexor Apex
To HelixTo Helix
AdvancedAdvanced
GPS EthernetGPS Ethernet
ConnectorConnector
Helix AdapterHelix Adapter
CableCable
(provided)(provided)

20 | minnkota.johnsonoutdoors.com ©2023 Johnson Outdoors Marine Electronics, Inc.
DUAL SPECTRUM CHIRP
All Dual Spectrum CHIRP Ulterra QUEST motors are equipped with an internal bonding wire. Incorrect rigging will cause sonar
interference and can damage your trolling motor, electronics, and other boat accessories. To minimize trolling motor interference,
ensure that the fish finder and trolling motor are powered by separate batteries. Refer to the "Battery & Wiring Installation" section of
this manual for correct rigging instructions.
The Dual Spectrum CHIRP cables are shielded to minimize interference. To protect this shielding, the cables should not be pulled tight
against sharp angles or hard objects. If using cable ties, do not over-tighten. Any excess cable should be bundled in a loose loop of no
less than 4” in diameter. The connection cable should be routed to the fish finder following Minn Kota recommendations on routing the
cables to optimize mobility and maximize functionality. Follow the instructions below for completing all connections and then follow the
instructions for "Securing Accessory Cables" to complete the output cable installation.
CAUTION
Failure to follow the recommended wire routing for installed features, if equipped, may cause damage to the product and void your
product warranty. Route cables away from pinch points or other areas that may cause them to bend in sharp angles. Routing the cables
in any way other than directed may cause damage to the cables by being pinched or severed. Do not over-tighten the cable ties as it may
damage the wires.
NOTICE: Your fish finder should be turned o
until this procedure is complete.
NOTICE: For instructions on deploying the
Ulterra QUEST, see the “Quick Stow & Deploy”
section of this manual.
a. Place the motor in the deployed position.
1
Fourteen-PinFourteen-Pin
ConnectorConnector
Fourteen-PinFourteen-Pin
ConnectorConnector
DualDual
SpectrumSpectrum
CHIRPCHIRP
Coil CordCoil Cord
1b
b. Locate the Fourteen-Pin Connector at the end
of the Dual Spectrum CHIRP accessory cable.
The cable will exit the base of the Control Head and
run down the center of the Coil Cord.
c. Determine if the Plug on the end of the Dual
Spectrum CHIRP accessory cable will be attached
directly to:
1) a Humminbird® Solix or Apex fish finder,
2) a Dual Spectrum CHIRP Extension Cable,
3) a Helix Adapter Cable or a compatible fish finder
adapter cable.