MINN KOTA CE Master User manual

Features
Installation
Cautions
Operation
Battery
Circuit Breaker
Wiring Diagram
Propeller Replacement
Maximizer
Maintenance
Troubleshooting
Warranty
serial number
purchase date
NOTE: Do not return your Minn Kota motor to your retailer. Your
retailer is not authorized to repair or replace this unit. You may
obtain service by:
•calling Minn Kota at 1-800-227-6433 or 1-507-345-4623;
•returning your motor to the Minn Kota Factory Service Center;
•sending or taking your motor to any Minn Kota authorized
service center on enclosed list.
Please include proof of purchase, serial number and purchase
date for warranty service with any of the above options.
pg. 2-3
pg. 4
pg. 5
pg. 6-8
pg. 9-10
pg. 10
pg. 11-12
pg. 13
pg. 13
pg. 13
pg. 13
pg. 14
RIPTIDE
TRANSOM
MOUNT
MOTORS
CE Master User Manual for RIPTIDE
PLEASE THOROUGHLY READ THIS USER MANUAL. FOLLOW ALL
INSTRUCTIONS AND HEED ALL SAFETY & CAUTIONARY NOTICES
BELOW. USE OF THIS MOTOR IS ONLY PERMITTED FOR PERSONS THAT
HAVE READ AND UNDERSTOOD THESE USER INSTRUCTIONS. MINORS
MAY USE THIS MOTOR ONLY UNDER ADULT SUPERVISION.

Specifications subject to change without notice.
FEATURES
TRAXXIS OVERVIEW
2
Battery Meter
Tilt Twist Tiller Extension & 6” Handle
One Hand Stow / Multi-position
Mounting Bracket
Lifetime Warranty Flexible Composite Shaft
Permanent Magnet Motor
Maximizer / Permanently Sealed
Electronics
(On select models)
Weedless Propeller
6” / 15mm

FEATURES
3
TRAXXIS MOUNT
Tilt Lock Button
Stop Pin
Clamp Screws
Quick Release Depth Collar
Steering Tension / Vertical Stow Knob
Transom

INSTALLATION OF THE PRODUCT:
Install the motor on the transom of the boat. Be sure to tighten the clamp screws securely.
CAUTION: OVER-TIGHTENING THE CLAMP SCREWS CAN DAMAGE THE BRACKET.
INSTALLATION
4
Tilt Lock Button
Stop Pin
Clamp Screws
Transom

CAUTIONS
5
Attention:
•Avoid running your motor with the propeller outside of the water. This may result in injuries from the rotating
propeller.
•It is recommended to set the speed selector to zero and place the motor in the deployed position prior to con-
necting power cables. Disconnect power cables prior to stowing.
•Always ensure that the power cables are not twisted or kinked; and that they are securely routed to avoid a
safety or trip hazard. Ensure cables are unobstructed in all locations to avoid damaging the wire insulation.
Damage to the insulation could result in failure or injury.
•Always inspect the insulation of the power cables prior to use to ensure they are not damaged.
•Disregarding these safety precautions may result in an electrical short of the battery(s) and/or motor. Always
disconnect the motor from the battery(s) before cleaning or checking the propeller.
•Avoid submerging the complete motor as water may enter the lower unit through control head and shaft.
Water in the lower unit may cause an electrical short and damage the lower unit. This damage will not be
covered by warranty.
Caution!
•Always operate the motor in a safe distance away from obstructions. Never approach the motor when the
propeller is running. Contact with a spinning propeller may endanger you or others.
•Always exercise safe practices when using your motor; stay clear of other watercrafts, swimmers, and any
floating objects. Always obey water regulations applicable to your area of operation.
•Never operate the motor while under the influence of alcohol, drugs, medication, or other substances which
may impair your ability to safely operate equipment.
•This motor is not suitable for use in strong currents exceeding the thrust level of the motor.
The constant noise pressure level of the motor during use is less than 70dB(A). The overall vibration level does
not exceed 2,5m/sec≈.

OPERATION
6
WARNING : WHEN RAISING OR LOWERING
MOTOR, KEEP FINGERS CLEAR OF ALL HINGE
AND PIVOT POINTS AND ALL MOVING PARTS.
Tilt Lock Button
Steering Tension /
Vertical Stow Knob
Quick Release Depth Collar Lift here
OPERATION OF THE PRODUCT:
Stowing and Deploying Your Motor: There are 2 methods for stowing your motor for travel:
Horizontal Stow: Loosen the steering tension knob, grab the back of the motor head or the motor shaft, while lifting up, tilt
the motor into the boat (the motor must be lifted approximately 1/2” to disengage locking pins). The bracket will ratchet into
a locked position. Be sure to retighten the steering tension knob and slide the quick release depth collar down to the top
of the steering tension knob for transport. To deploy your motor from this stowed position, loosen the quick release collar,
reposition and retighten to desired depth location, hold the motor shaft or head firmly, and loosen the steering tension knob,
press the tilt lock button while holding control head and gently lower the motor into the water. Retighten the quick release
collar. Retighten the steering tension knob to the desired steering tension.
Vertical Stow: While firmly holding the motor shaft, loosen the steering tension knob and lift up on the motor. Retighten the
steering tension knob to retain the vertical stow position of the motor. Be sure to slide the quick release depth collar down
to the top of the steering tension knob for added security. To deploy your motor from this vertically stowed position, loosen
the quick release collar, hold the motor shaft firmly, and loosen the steering tension knob, and gently lower the motor into
the water. Retighten the quick release collar. Retighten the steering tension knob to the desired steering tension.

OPERATION
7
CAUTION: NEVER OPERATE YOUR MOTOR WHEN IT IS OUT OF THE WATER.
OPERATION OF THE PRODUCT CONT’D:
Tilt and Extension Handle Operation:
Your TRAXXIS trolling motor features 7 usable handle tilt positions…45°, 30°, and 15° up and down from the 0° (horizon-
tal) position. To use the down positions, you must first press the release button located on the left underside of the pivot
handle.
Your TRAXXIS trolling motor handle also features a unique stow position, that is useful for limiting the amount of space
required for storage or travel.
First press the release button located on the left underside of the pivot handle, then push the handle down until you feel
the handle “lock in” to the stowed position. This will be almost parallel to the motor shaft.
To extend the handle, pull the handle towards you to the desired position. The handle will extend a full 6 inches.
To retract, push the handle in until it meets the face of the motor control head.
Handle controls on/off,
steering, forward/reverse
Release button
IMPORTANT: THE MOTOR MUST BE IN THE OFF POSITION TO USE TO USE THE STOW POSITION! FAILURE TO
PUT THE MOTOR IN THE OFF POSITION BEFORE STOWING THE HANDLE WILL RESULT IN JOINT FAILURE.

OPERATION
8
OPERATION OF THE PRODUCT CONT’D:
Steering Tension Adjustment:
The steering tension can be adjusted by tightening or loosening the steering tension knob for the desired steering tension.
Depth Adjustment
The Quick Release Depth Collar can easily be adjusted by opening the lever arm to release to depth collar, sliding it to
the desired depth, and then closing the lever arm again. The tension of the quick release depth collar can be adjusted
with a screw driver to obtain the proper “feel”. Be careful not to over tighten!
Lever Arm
Steering Tension /
Vertical Stow Knob
PINCH POINT WARNING!!
BE SURE TO FIRMLY HOLD THE MOTOR SHAFT
WHENEVER MAKING ADJUSTMENTS TO THE QUICK
RELEASE DEPTH COLLAR, OR TO THE STEERING
TENSION ADJUSTMENT KNOB. THE MOTOR CAN
SLIDE DOWN QUICKLY AND CAUSE INJURY.

BATTERY
9
BATTERY INFORMATION:
The motor will operate with any deep cycle marine 12 volt battery/batteries. For best results use a deep cycle, marine battery with at
least a 115 ampere hour rating. As a general on the water estimate, your 12 volt motor will draw one ampere per hour and your 24
volt motor will draw .75 ampere per hour for each pound of thrust produced when the motor is running on high. The actual ampere
draw is subject to your particular environmental conditions and operation requirements. Maintain battery at full charge. Proper
care will ensure having battery power when you need it, and will significantly improve the battery life. Failure to recharge lead-acid
batteries (within 12-24 hours) is the leading cause of premature battery failure. Use a variable rate charger to avoid overcharging.
If you are using a crank battery to start a gasoline outboard, we recommend that you use a separate deep cycle marine battery/
batteries for your Minn Kota trolling motor.
Advice regarding batteries:
Never connect the (+) and the (–) terminals of the battery together. Take care that no metal object can fall onto the battery
and short the terminals. This would immediately lead to a short and utmost fire danger.
Recommendation: Use battery boxes and covered battery terminal clamps like Minn Kota accessory #MK-BC-1.
These motors are equipped with a “push to test” battery gauge. The LED provides an accurate display of the remaining charge in
the battery. It is only accurate when the motor is off. The gauge reads as:
• Four lights indicate full charge.
• Three lights indicate good charge.
• Two lights indicate low charge.
• One light indicates recharge.

BATTERY CONNECTION CIRCUIT BREAKER
10
BATTERY CONNECTION
12 Volt Systems:
1. Make sure that the motor is switched off (speed selector on “0”).
2. Connect positive (+) red lead to positive (+) battery terminal.
3. Connect negative (–) black lead to negative (–) battery terminal.
4. For safety reasons do not switch the motor on until the propeller is in the water.
24 Volt Systems:
1. Make sure that the motor is switched off (speed selector on “0”).
2. Two 12 volt batteries are required.
3. The batteries must be wired in series, only as directed in wiring diagram, to provide 24 volts.
a. Connect a connector cable to positive ( + ) terminal of battery 1 and to negative ( – ) terminal of battery 2.
b.Connect positive (+) red lead to positive (+) terminal on battery 2.
c. Connect negative (–) black lead to negative (–) terminal of battery 1.
4. For safety reasons do not switch the motor on until the propeller is in the water.
36 Volt Systems:
1. Make sure that the motor is switched off (speed selector on “0”).
2. Three 12 volt batteries are required.
3. The batteries must be wired in series, only as directed in wiring diagram, to provide 36 volts.
a. Connect a connector cable to positive ( + ) terminal of battery 1 and to negative ( – ) terminal of battery 2.
b. Connect a connector cable to positive (+) terminal of battery 2 and to negative (–) terminal of battery 3.
c. Connect positive (+) red lead to positive (+) terminal on battery 3.
d. Connect negative (–) black lead to negative (–) terminal of battery 1.
4. For safety reasons do not switch the motor on until the propeller is in the water.
If installing a leadwire plug, observe proper polarity and follow instructions in your boat owner’s manual.
See wiring diagram on following pages.
• IMPROPER WIRING OF 24/36 VOLT SYSTEM COULD CAUSE BATTERY EXPLOSION!
• KEEP LEADWIRE WING NUT CONNECTION TIGHT AND SOLID TO BATTERY TERMINALS.
• LOCATE BATTERY IN A VENTILATED COMPARTMENT.
Boat Rigging and Motor Installation:
An over-current protection device (circuit breaker or fuse) must be used with this motor. Coast Guard requirements dic-
tate that each ungrounded current-carrying conductor must be protected by a manually reset, trip-free circuit breaker or fuse.
The type (voltage and current rating) of the fuse or circuit breaker must be sized accordingly to the trolling motor used. The
following breaker sizes are recommended guidelines:
Maximum thrust Voltage / Recommended circuit breaker rating
30# to 45# 12V 50A @ 12VDC
50# to 55# 12V 60A @ 12VDC
65# to 70# 24V 50A @ 24VDC
80# 24V 60A @ 24VDC
101# 36V 50A @ 36VDC
E-Drive 48V 40A @ 48VDC
The appropriate wire size needed to connect your trolling motor to the trolling motor batteries varies depending on the length
of cable needed and voltage of the motor. For additional information, please consult appropriate ABYC (American Boat and
Yacht Council) and Coast Guard requirements.
Reference:
United States Code of Federal Regulations: 33 CFR 183 – Boats and Associated Equipment
ABYC E-11: AC and DC Electrical Systems on Boats

WIRING DIAGRAM
11
12-24 VOLT 5 SPEED MODELS
FIVE SPEED SWITCH
INTERRUPTEUR A CING VITESSES
12v
24v
RED M+
BLACK M -
BLACK M -
RED B+
WHITE
YELLOW
RED
BLACK
12V BATT 1
12V BATT 1 12V BATT 2
MOTOR
THIS IS A UNIVERSAL MULTI-VOLTAGE DIAGRAM. DOUBLE CHECK YOUR MOTORS VOLTAGE FOR PROPER CONNEC-
TIONS
Over-Current Protection Devices not shown in illustrations.

WIRING DIAGRAM
12
12v
24v
36v
12-24-36 VOLT VARIABLE SPEED MODELS
RED M+
BLACK CONTROL BOARD
RED
BLACK
BATTERY GAUGE
12V BATT 1
BLACK B-
RED B+
MOTOR
SPEED ADJUSTMENT KNOB
12V BATT 1
12V BATT 1
12V BATT 2
12V BATT 3
12V BATT 2
THIS IS A UNIVERSAL MULTI-VOLTAGE DIAGRAM. DOUBLE CHECK YOUR MOTORS VOLTAGE FOR PROPER CONNEC-
TIONS
Over-Current Protection Devices not shown in illustrations.

MAINTENANCE OF THE PRODUCT:
1. After use, these units should be rinsed with fresh water,
then wiped down with a cloth dampened with an aque-
ous based silicone spray such as Armor All®.
2. The propeller must be cleaned of weeds and fishing line.
The line can get behind the prop, wear away the seals
and allow water to enter the motor. Check this after
every 20 hours of operation.
3. Before each use, check to see that the prop nut is
secure.
4. To prevent accidental damage during trailering or stor-
age, disconnect the battery whenever the motor is off of
the water. For prolonged storage, lightly coat all metal
parts with an aqueous based silicone spray.
5. For maximum performance, restore battery to full charge
before each use.
6. Keep battery terminals clean with fine sandpaper or
emery cloth.
7. The weedless wedge propeller is designed to provide
absolute weed free operation with very high efficiency.
To maintain this top performance, the leading edge of
the blades must be kept smooth. If they are rough or
nicked from use, restore to smooth by sanding with fine
sandpaper.
TROUBLESHOOTING:
1. Motor fails to run or lacks power:
• Check motor for obstructions. The motor may have gone
into current limit. To reset: return to off position, remove
obstruction and resume operation.
• Failure to put the motor in the off position before stow-
ing the handle will result in joint failure.
• Check battery connections for proper polarity.
• Make sure terminals are clean and corrosion free. Use
fine sandpaper or emery cloth to clean terminals.
• Check battery water level. Add water if needed.
2. Motor looses power after a short running time:
• Check battery charge, if low, restore to full charge.
3. Motor is hard to steer:
• Loosen the steering tension knob on the top of bracket.
• Lubricate the composite shaft.
4. Bracket shifts or “walks” on transom:
• With some boats, the transom bracket may loosen or shift
during heavy use.
5. You experience prop vibration during normal operation:
• Remove and rotate the prop 180°. See removal instruc-
tions in prop section.
NOTE: For all other malfunctions, see enclosed authorized
service center listing for nearest service center.
PROPELLER MAXIMIZER MAINTENANCE
TROUBLESHOOTING
13
PROPELLER REPLACEMENT:
• Disconnect motor from battery prior to changing the
propeller.
• Hold the propeller and loosen the anode/nut with a
wrench.
• Remove anode/nut and washer. If the drive pin is
sheared/broken, you will need to hold the shaft steady
with a screwdriver blade pressed into the slot on the
end of the shaft.
• Turn the old prop to horizontal (as illustrated) and pull it
straight off. If drive pin falls out, push it back in.
• Align new propeller with drive pin.
• Install prop washer and anode/nut.
• Tighten anode/ nut 1/4 turn past snug. [25-35 inch lbs.]
Be careful, over tightening can damage prop.
anode/nut
Slot End
Washer
Drive pin
Weedless Propeller
CAUTION: DISCONNECT THE MOTOR
FROM THE BATTERY BEFORE BEGINNING
ANY PROP WORK OR MAINTENANCE.
MAXIMIZER™: (On Select Models)
The built-In Maximizer’s electronics create pulse width modulation to provide longer running time and extended battery life.
With the Maximizer speed control, you may, in some applications, experience interference in your depth finder display.
We recommend that you use a separate deep cycle marine battery for your trolling motor and that you power the depth
finder from the starting / cranking battery. If problems still persist, call our service department at 1-800-227-6433.

BOAT RIGGING AND PRODUCT INSTALLATION:
For safety and compliance reasons, we recommend that you follow American Boat and Yacht Council
(ABYC) standards when rigging your boat. Altering boat wiring should be completed by a qualified marine
technician. The following specifications are for general guidelines only:
CAUTION: These guidelines apply to general rigging to support your Minn Kota Motor. Powering multiple
motors or additional electrical devices from the same power circuit may impact the recommended conductor
gauge and circuit breaker size. If you are using wire longer than that provided with your unit, follow the
conductor gauge and circuit breaker sizing table below. If your total conductor length is more than 50 feet we
recommend that you contact a qualified marine technician.
An over-current protection device (circuit breaker or fuse) must be used. Coast Guard requirements
dictate that each ungrounded current-carrying conductor must be protected by a manually reset, trip-free
circuit breaker or fuse. The type (voltage and current rating) of the fuse or circuit breaker must be sized
accordingly to the trolling motor used. The table below gives recommended guidelines for circuit breaker
sizing.
*Conductor Gauge and Circuit Breaker Sizing Table
Total Conductor Length (length of all conductors in the total circuit)
Motor Thrust Circuit Breaker 10 feet 20 feet 30 feet 40 feet 50 feet
30# 12 AWG 10 AWG 8 AWG 6 AWG 4 AWG
40#, 45# 50 Amp @ 12 VDC
10 AWG 8 AWG 6 AWG 4 AWG 4 AWG
50#, 55# 60 Amp @ 12 VDC 8 AWG 6 AWG 4 AWG 4 AWG 2 AWG
70# 50 Amp @ 24 VDC 10 AWG 10 AWG 8 AWG 8 AWG 6 AWG
80# 60 Amp @ 24 VDC 8 AWG 8 AWG 8 AWG 6 AWG 6 AWG
101# 50 Amp @ 36 VDC 8 AWG 8 AWG 8 AWG 8 AWG 8 AWG
E-Drive 40 Amp @ 48 VDC 10 AWG 10 AWG 8 AWG 6 AWG 6 AWG
*The conductor and circuit breaker sizing table above is only valid for the following assumptions.
1. No more than 3 conductors are bundled together inside of a sheath or conduit outside of engine
spaces.
2. Each conductor has 105oC temp rated insulation.
3. No more than 5% voltage drop allowed at full motor power based on published product power
requirements.
Reference:
United States Code of Federal Regulations: 33 CFR 183 – Boats and Associated Equipment
ABYC E-11: AC and DC Electrical Systems on Boats

BATEAU GRÉEMENT ET PRODUIT DE L'INSTALLATION :
Pour des raisons de sécurité et de conformité, nous recommandons de suivre les normes de l’American
Boat And Yacht Council (ABYC) lorsque truquer votre bateau. Modifier le câblage du bateau doit être
complété par un technicien marin qualifié. Les spécifications suivantes sont uniquement des directives
générales :
Avertissement : Ces directives s'appliquent au gréement générale à l'appui de votre moteur Minn Kota.
Alimenter plusieurs moteurs ou des dispositifs électriques supplémentaires depuis le même circuit de
puissance peut influencer la taille recommandée de la jauge du conducteur et disjoncteur. Si vous utilisez fil
plus long que celui fourni avec votre unité, suivre le conducteur jauge et le disjoncteur dimensionnement
tableau ci-dessous. Si la longueur totale de votre conducteur est plus de 15 mètres nous recommandons
que vous contacter un technicien marin qualifié.
Un dispositif de protection de surintensité (disjoncteur ou fusible) doit être utilisé. Les exigences de
la Garde-Côte américain disent que chaque conducteur sans fondement de porteurs de courant doit être
protégé par un disjoncteur mise en circuit, à déclenchement libre ou un fusible. Le type (tension et courant
nominal) du fusible ou disjoncteur doit être dimensionné en conséquence pour le moteur utilisé. Le tableau
ci-dessous donne les directives pour le calibrage de disjoncteur.
* Jauge de conducteur et disjoncteur Table de dimensionnement
Longueur totale de chef d'orchestre (longueur de tous les conducteurs dans le
circuit total)
Moteur
p
oussée Disjoncteur 3 mètres 6 mètres 9 mètres 12 mètres 15 mètres
30# 3 mm 5 mm 8 mm 13 mm 21 mm
40#, 45#
Amp 50 @ 12 VDC
5 mm 8 mm 13 mm 21 mm 21 mm
50#, 55# Amp 60 @ 12 VDC 8 mm 13 mm 21 mm 21 mm 32 mm
70# Amp 50 @ 24 VDC 5 mm 5 mm 8 mm 8 mm 13 mm
80# Amp 60 @ 24 VDC 8 mm 8 mm 8 mm 13 mm 13 mm
101# Amp 50 @ 36 VDC 8 mm 8 mm 8 mm 8 mm 8 mm
E-Drive Amp 40 @ 48 VDC 5 mm 5 mm 8 mm 13 mm 13 mm
* Le disjoncteur tableau ci-dessus de dimensionnement et chef d'orchestre est uniquement valable
pour les hypothèses suivantes.
1. Pas plus de 3 conducteurs sont regroupés à l'intérieur d'une gaine ou conduites à l'extérieur des
espaces de moteur.
2. Chaque conducteur a 105oc temp, évalué à isolation.
3. Pas plus d'une chute de tension de 5 % a permis à la puissance du moteur complet en fonction
des besoins de puissance produit publié.
Référence :
United States Code of Federal Regulations : CFR 33 183 – bateaux et équipement connexe
ABYC E-11: AC et DC des systèmes électriques à bord de bateaux

REPAIR AND TROUBLESHOOTING
We off er several options to help you troubleshoot and/or repair your product. Please read through the options listed below.
FREQUENTLY ASKED QUESTIONS
Did you know that we have over 100 FAQ’s to help answer all of your Minn Kota questions? Visit www.minnkotamotors.com
and click on “Frequently Asked Questions” under the “Service” tab to fi nd an answer to your question.
http://www.minnkotamotors.com/service/faq.aspx?linkidentifi er=id&itemid=817
AUTHORIZED SERVICE CENTERS
Minn Kota has over 300 authorized service centers in the United States and Canada where you can purchase parts or get your
products repaired. Please visit www.minnkotamotors.com and click on “Service Center Locator” under the “Service” tab to
locate a service center in your area.
http://www.minnkotamotors.com/service/asclocator.aspx
CALL US (FOR U.S. AND CANADA)
Our customer service representatives are available Monday – Friday between 7:00am – 4:30pm CST at 800-227-6433. If you
are calling to order parts, please have the 11-character serial number from your product, specifi c part numbers, and credit card
information available. This will help expedite your call and allow us to provide you with the best customer service possible. You
can reference the parts list located in your manual to identify the specifi c part numbers.
EMAIL US
You can email our customer service department with questions regarding your Minn Kota products. To email your quesiton, visit
www.minnkotamotors.com and click on “Contact Us” under the “Service” tab.
http://www.minnkotamotors.com/service/contact.aspx

350 356
5
10
85
15
100
35
40
80
90
1000
1010
1015
1020
50
110
120
115
60
65
1
70
20
95
30
25
200
205
210
210
400
395
220
225
245
265
270
275
290
300
320
325
330
305
310
135
136
235
215
410
405
260 255
335
295
230
390
360
365
370 375
380
385 420
425
280 285
315
240
250
415
340
345
355
208
RT80/T
80 LBS THRUST
24 VOLT
42” SHAFT
PARTS LIST
This page provides MinnKota® WEEE compliance disassembly instructions. For more information
about where you should dispose of your waste equipment for recycling and recovery and/or your
European Union member state requirements, please contact your dealer or distributor from which
your product was purchased.
Tools required: Flat Head screw driver, Phillips screw driver, Socket set, Pliers.
317
345
316

In the U.S.A., replacement parts may be ordered directly from MINN KOTA Parts Dept., 121 Power Drive,P.O. Box 8129 Mankato, Minnesota 56002-8129. In Canada, parts may be ordered from any of the Canadian Authorized Service Centers shown on the enclosed list. Be sure to provide the model and serial numbers of your motor when ordering parts. Please use the correct part numbers from the parts
list. Payment for any parts ordered from the MINN KOTA parts department, may be by cash, personal check, Discover Card, MasterCard or VISA. To order, call 1-800-227-6433 or FAX [phone].
* This item is part of an assembly. This item cannot be sold separately due to machining and /or assembly that is required. P/N 2094917 REV. K ECN 33752 2-12
Fuera de los Estados Unidos, consultar la lista anexa para ubicar el Centro de servicio autorizado MINN KOTA. No dejar de incluir el número del MODELO y el número de SERIE del motor para el cual se solicitan las piezas. Usar siempre los números de pieza correctos indicados en la lista de piezas.
PARTS LIST
PARTS LIST
Item P/N Description Qty Item P/N Description Qty Item P/N Description Qty Item P/N Description Qty
1 2316228 24V Motor 42” SW 1 5 2-100-214 Armature assembly 1 10 140-010 Bearing 1 15 788-040 Retaining ring 1 20 2-200-397 Center housing assemby 1 25 2-300-340 Brush end housing assembly 1 30 421-376 Plain end housing assembly STD 1 35 144-017 Flange bearing 1 40 880-025 Seal 2 50 188-094 Brush 2 60 9-738-004 Brush plate assembly 1 65 975-041 Brush spring 2 70 701-043 O-ring, motor 2 80 701-009 O-ring, thru-bolt 2 85 830-027 Screw, 10-32 x 2 2 90 830-094 Thru-bolt 2 95 990-051 Washer, steel 2 100 990-052 Washer, nylatron 2 110 973-025 Spacer, brush plate 2 115 992-010 Washer, Belleville 2 120 992-045 Spacer, thrust 1 135 640-018 Leadwire, black 1 136 640-123 Leadwire, red 1 n2889460 Seal and O-ring Kit 200 2195659 Decal, c-box cover 1 205 2060296 C-box cover 1 208 2325666 Decal - MinnKota 2 210 2074081 Battery meter, 24v SW 1 215 2043427 Screw, #8 x 7/8 SS 2 220 2184017 Control board, 24/36V 1 n 2888411 Potentiometer Replacement Kit 225 2303434 Screw, #8-30 x 5/8 SS 2 230 2062503 Control box, VARS, SW 1 235 2062905 Strain relief 1 240 2303412 Screw, #6 x 5/8 SS 6 245 2263434 Screw, #8 x 1 SS 2 250 2383406 Screw, #10-24 x 2 PPH SS 1 255 2061517 Collar, c-box 1 260 2333101 Nut, 10-24, nylock, SS 1 265 2991521 Cam lock/depth collar assy 1
n2991798 Bracket assy, Aluminum [270-356] 1 270 2060100 Knob, steering tension, soft 1 275 2068400 Collet 1 280 2064200 Lock arm 1 285 2062701 Spring, lock arm 1 290 2061821 Hinge 1 295 2062603 Pin, lock, ss 1 300 2062603 Pin, lock, ss 1 305 2037301 Bushing, hinge 1 310 2002012 Tube 42” 1 315 2063501 Bolt 1/4-20 x 2 3/8”, ss 3 316 2061301 Screw-clamp 2 317 2331700 Washer-clamp screw 2 320 2771949 Bracket, right, SW 1 325 2067905 Cam deactivator 1 330 2067306 Bushing, dowel 1/4 x 1/2 3
335 2062702 Spring, cam deactivator 1 n 2771303 Clamp screw kit 2 per kit 340 2050925 Handle, clamp 2 345 2052625 Roll pin 2 350 2771948 Bracket, left, SW 1 355 2263103 Nut, 1/4-20, nylock, ss 3 356 2062604 Pin, stop 1 n 2990957 Handle assy, VARS [360-410] 1 360 2990456 Grip/handle assy, VARS [360-375] 1 365 2060015 Bearing, handle 2 370 2063405 Screw, #6 PFH SS 1 375 2884092 Yoke / spider assy, VARS 1 380 2302742 Spring, detent, off 1 385 2060005 Bearing, handle pivot 2 390 2060900 Handle pivot, top 1 395 2302745 Spring, release button 1 400 2063700 Button, release 1 405 2060905 Handle pivot, bottom 1 410 2303412 Screw, #6 x 5/8 SS 6 415 2062715 Spring, handle pivot 1 420 2061700 Washer, pot holder 1 425 2992523 Leadwire assy, includes [235] 1
 n  1378132 Propeller kit WW2 n  2994876 Propeller bag assy 1000 2331160 Propeller WW2 1 1010 2262658 Drive pin, large 1 1015 2091701 Washer, prop, large 1 1020 2198401 Nut, nylock, prop, Anode 1

ENVIRONMENTAL COMPLIANCE STATEMENT:
It is the intention of Johnson Outdoors Marine Electronics, Inc. to be a responsible corporate citizen, operating in compliance with
known and applicable environmental regulations, and a good neighbor in the communities where we make or sell our products.
WEEE Directive:
EU Directive 2002/96/EC “Waste of Electrical and Electronic Equipment Directive (WEEE)” impacts most distributors, sellers, and
manufacturers of consumer electronics in the European Union. The WEEE Directive requires the producer of consumer electron-
ics to take responsibility for the management of waste from their products to achieve environmentally responsible disposal during
the product life cycle.
WEEE compliance may not be required in your location for electrical & electronic equipment (EEE), nor may it be required for EEE
designed and intended as fixed or temporary installation in transportation vehicles such as automobiles, aircraft, and boats. In
some European Union member states, these vehicles are considered outside of the scope of the Directive, and EEE for those
applications can be considered excluded from the WEEE Directive requirement.
This symbol (WEEE wheelie bin) on product indicates the product must not be disposed of with other household refuse. It must be
disposed of and collected for recycling and recovery of waste EEE. Johnson Outdoors Marine Electronics,
Inc. will mark all EEE products in accordance with the WEEE Directive. It is our goal to comply in the collec-
tion, treatment, recovery, and environmentally sound disposal of those products; however, these requirement
do vary within European Union member states. For more information about where you should dispose of your
waste equipment for recycling and recovery and/or your European Union member state requirements, please
contact your dealer or distributor from which your product was purchased.
Disposal:
Minn Kota motors are not subject to the disposal regulations EAG-VO (electric devices directive) that implements
the WEEE directive. Nevertheless never dispose of your Minn Kota motor in a garbage bin but at the proper place of collection of
your local town council.
Never dispose of battery in a garbage bin. Comply with the disposal directions of the manufacturer or his representative and dispose
of them at the proper place of collection of your local town council.

Composite Shaft
Johnson Outdoors Marine Electronics, Inc. warrants to the
original purchaser that the composite shaft of the purchas-
er’s Minn Kota® trolling motor is free from defects in mate-
rials and workmanship appearing within the original pur-
chaser’s lifetime. Johnson Outdoors Marine Electronics,
Inc. will provide a new shaft, free of charge, to replace any
composite shaft found to be defective more than two (2)
years after the date of purchase. Providing such a new
shaft shall be the sole and exclusive liability of Johnson
Outdoors Marine Electronics, Inc. and the sole and exclu-
sive remedy of the purchaser for breach of this warranty;
and purchaser shall be responsible for installing, or for the
cost of labor to install, any new composite shaft provided
by Johnson Outdoors Inc.
Entire Product
Johnson Outdoors Marine Electronics, Inc. warrants to the
original purchaser that the purchaser’s entire Minn Kota®
trolling motor is free from defects in materials and work-
manship appearing within two (2) years after the date of
purchase. Johnson Outdoors Marine Electronics, Inc. will,
at its option, either repair or replace, free of charge, any
parts, including any composite shaft, found to be defective
during the term of this warranty. Such repair or replace-
ment shall be the sole and exclusive liability of Johnson
Outdoors Marine Electronics, Inc. and the sole and exclu-
sive remedy of the purchaser for breach of this warranty.
Terms Applicable to Both Warranties
These limited warranties do not apply to motors used com-
mercially nor do they cover normal wear and tear, blemish-
es that do not affect the operation of the motor, or damage
caused by accidents, abuse, alteration, modification, mis-
use or improper care or maintenance. DAMAGE TO
MOTORS CAUSED BY THE USE OF REPLACEMENT
PROPELLERS OR OTHER REPLACEMENT PARTS NOT
MEETING THE DESIGN SPECIFICATIONS OF THE
ORIGINAL PROPELLER AND PARTS WILL NOT BE COV-
ERED BY THIS LIMITED WARRANTY. The cost of normal
maintenance or replacement parts which are not defective
are the responsibility of the purchaser.
To obtain warranty service in the U.S., the motor or part
believed to be defective, and proof of original purchase
(including the date of purchase), must be presented to a
Minn Kota® Authorized Service Center or to Minn Kota®’s
factory service center in Mankato, MN. Any charges
incurred for service calls, transportation or shipping/freight
to/from the Minn Kota® Authorized Service Center or facto-
ry, labor to haul out, remove, re-install or re-rig products
removed for warranty service, or any other similar items
are the sole and exclusive responsibility of the purchaser.
Motors purchased outside of the U.S.
must be returned prepaid with proof of purchase
(including the date of purchase and serial number) to any
Authorized Minn Kota® Service Center in the country of
purchase. Warranty service can be arranged by contacting
a Minn Kota® Authorized Service Center listed on the
enclosed sheet, or by contacting the factory at 1-800-227-
6433 or fax [phone]. Note: Do not return your
Minn Kota® motor to your retailer. Your retailer
is not authorized to repair or replace them.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN
THESE LIMITED WARRANTIES. IN NO EVENT SHALL
ANY IMPLIED WARRANTIES (EXCEPT ON THE COM-
POSITE SHAFT), INCLUDING ANY IMPLIED WAR-
RANTIES OF MERCHANTABILITY OR FITNESS FOR
PARTICULAR PURPOSE, EXTEND BEYOND TWO
YEARS FROM THE DATE OF PURCHASE. IN NO
EVENT SHALL JOHNSON OUTDOORS MARINE
ELCTRONCIS, INC. BE LIABLE FOR INCIDENTAL, CON-
SEQUENTIAL OR SPECIAL DAMAGES.
Some states do not allow limitations on how long an
implied warranty lasts or the exclusion or limitation of inci-
dental or consequential damages, so the above limitations
and/or exclusions may not apply to you. This warranty
gives you specific legal rights and you may also have other
legal rights which vary from state to state.
LIMITED LIFETIME WARRANTY ON COMPOSITE SHAFT,
LIMITED TWO-YEAR WARRANTY ON ENTIRE PRODUCT:
“WARNING: This product contains chemical(s) known to the state of California to cause cancer and/or reproductive toxicity.”
LIMITED WARRANTY
14