Minolta MND50 User manual

MND50 User Manual

1. About Your Camera
1
About this Manual
Congratulations on purchasing the Minolta MND50 Digital Camera!
The contents of this manual are subject to change without notice. Note that the
differ
somewhat from the screens and configuration of the actual camera.
Copyright
This manual contains proprietary information protected by copyright. All rights
are reserved. No part of this manual may be reproduced by any mechanical,
electronic or other means, in any form, without prior written permission of Elite
Brands Inc. © 2022.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1)
This device may not cause harmful interference and
(2)
This device must accept any interference received, including interference
that may cause undesired operation.
RF Exposure Warning
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment must be installed and operated in
accordance with provided instructions and must not be co-located or operating in
conjunction with any other antenna or transmitter. End-users and installers must
be provided with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance.

1. About Your Camera
2
FCC: SAR standard Value: 1.6 W/Kg, Maximal Measure: 0.4 W/kg
CE Mark Warning
This is a Class B product, in a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
Safety and Handling Precautions
Camera Information
Do not disassemble or attempt to service the camera yourself.
Do not expose the camera to moisture, or extreme temperatures.
Allow the camera to warm up when moving from cold to warm temperatures.
Do not touch and put pressure on the camera lens.
Do not expose the lens to direct sunlight for extended periods.
Do not use abrasive chemicals, cleaning solvents or strong detergents to clean
the product. Wipe the product with a slightly damp soft cloth.
Do not use the flash or LED Light near a person's eyes to prevent possible eye
injury.
To prevent you from falling over or resulting in traffic accident, please do not
use the camera while you are walking, driving or riding a vehicle.
Please handle the camera strap with care, and never place the strap around
the neck of an infant or child. Wrapping the strap around a neck may cause
suffocation.
Do not subject the LCD screen to impact.
To prevent the risk of fire or electric shock, do not expose the inside of this
product to rain or moisture.
Battery Information
Turn off the camera before installing or removing the battery.
Use only the provided batteries or type of battery and charger that came with
your camera. Using other types of battery or charger may damage the device
and invalidate the warranty.
Inserting the battery upside down can cause damage to the product and
possibly cause an explosion.
When the camera is used for an extended period of time, it is normal for the
camera body to feel warm.
Download all pictures and remove the battery from the camera if you are going
to store the camera for a long period of time.
Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
Please keep the batteries out of the reach of children to prevent from
swallowing the batteries, which might cause poisoning.
If the battery's color or shape changes in any way, stop using the battery
immediately.

1. About Your Camera
3
USB Adaptor Information
Do not expose the adapter to high temperatures or moisture places. Otherwise, it
may cause fire or electric shock.
Do not attempt to repair, disassemble, change or transform the adapter.
Avoid sudden changes in temperature, which may cause condensation on the
Do not touch the plug with wet hands. Otherwise, it may cause electric shock.
Do not use the travel voltage converter or AC/DC power inverter. Otherwise, it
may cause damage, overheating, malfunction or fire to the camera.
Notes about Opening and Closing the Battery Door
Make sure the camera and your hands are not wet.
Make sure that there are no debris inside the battery-chamber or memory card
slot.
lock position.
Precautions When Cleaning
Do not puncture the microphone or speaker openings with a sharp implement.
If the inside of the camera is damaged, the waterproof performance will
deteriorate.
Do not use soap, natural detergents, or chemicals such as benzene for
cleaning.
Do Not Apply Strong Impact to the Camera
The product may malfunction if subjected to strong shock or vibration. In
addition, do not touch or apply force to the lens.
Avoid Sudden Changes in Temperature
Sudden changes in temperature, such as when entering or leaving a heated
building on a cold day, can cause condensation to form inside the device. To
prevent condensation, place the device in a carrying case or a plastic bag
before exposing it to sudden changes in temperature.
Keep Away from Strong Magnetic Fields
Do not use or store this device in the vicinity of equipment that generates strong
electromagneti
data or camera malfunction.
Do Not Point the Lens at Strong Light Sources for Extended Periods
Avoid pointing the lens at the sun or other strong light source light sources for
extended periods when using or storing the camera. Intense light may cause
before Removing or Disconnecting the Power

1. About Your Camera
4
Source or Memory Card
Do not remove the battery while the product is on, or while images are being
saved or deleted. Forcibly cutting power in these circumstances could result in
loss of data or cause damage to the memory card or internal circuitry.
Notes about the LCD Screen
The LCD Screen is constructed with extremely high precision; At least 99.99%
Hence, while these displays may contain pixels that are always lit (white, red,
on images recorded with the device.
lighting.
Do not apply pressure to the LCD screen, as this could cause damage or
malfunction.
The Battery
Precautions for Use
Note that the battery may become hot after use.
Do not use the battery at ambient temperatures below 0°C (32°F) or above
40°C (104°F) as this could cause damage or malfunction.
If you notice any abnormalities such as excessive heat, smoke, or an unusual
smell coming from the battery, immediately discontinue use and consult your
retailer.
After removing the battery from the camera or optional battery charger, put the
battery in a plastic bag, etc. in order to insulate it.
Charging the Battery
Check the battery level before using the camera and replace or charge the
battery if necessary.
Charge the battery indoors with an ambient temperature of 5°C (41°F) to 35°C
(95°F) before use.
A high battery temperature may prevent the battery from charging properly or
completely, and may reduce battery performance. Note that the battery may
become hot after use; wait for the battery to cool before charging. When
charging the battery inserted into this camera using the Charging AC Adapter
or a computer, the battery is not charged at battery temperature below 5°C
(41°F) or above 55°C (131°F).
When the battery is between 45°C (113°F) - 55°C (131°F), the chargeable
capacity may decrease.
Do not continue charging once the battery is fully charged as this will result in
reduce battery performance.
The battery temperature may increase during charging. However, this is not a
malfunction.

1. About Your Camera
5
Using the Battery When Cold
On cold days, the capacity of batteries tends to decrease. If an exhausted
battery is used at a low temperature, the camera may not turn on. Keep spare
batteries in a warm place and exchange as necessary. Once warmed, a cold
battery may recover some of its charge.
Recycling Used Batteries
Replace the battery when it no longer holds a charge. Used batteries are a
valuable resource. Please recycle used batteries in accordance with local
regulations.
Cleaning After Using the Camera
Use a blower to remove any dust or lint that adheres to the lens, monitor or
ther stains that cannot be removed
with a blower, gently wipe the parts with a soft dry cloth. If you wipe with too
much pressure or with a rough cloth, it may damage the camera or cause a
malfunction.
Storage
If you do not intend to use the camera for an extended period, remove the
battery and avoid storing the camera in any of the following types of locations:
Places that are poorly ventilated or subject to humidity of over 60%
Place exposed to temperatures above 50°C (122°F) or below -10°C (14°F).
television or radios.
To prevent mold or mildew, take the camera out of storage at least once a
month, and turn it on and release the shutter a few times before putting it away
again.

6
1.1
Camera Interface
LCD
Screen
Strap
Mount
Ok |
Mode
Port
Door
Delete
Display
ISO
Playback
Up | Flash
Left | Self
Timer
Down | Mute Menu Right | Exposure
Speaker
Scene Dial Power Record
Shutter
Zoom
Lens
Microphone
Flash
LED Status
Indicator
1. About Your Camera

7
1.2
Button Function Description
Function Description
Power Press and hold for 3 seconds to power on. Tap to power
off.
Mode | OK
Tap to cycle between Photo, Video and Playback modes.
In Settings: Tap to confirm selected setting.
In Playback: Tap to start and stop video playback.
Zoom
In Video or Photo: Slide to zoom in and out.
In Playback: Slide to zoom in on the image displayed on
the screen.
Up | Flash In Photo: Tap to change the flash settings.
In Settings:
Tap
to
scroll through menus and submenus
.
Down | Mute
In Video or Photo: Tap to mute and unmute the button
sounds.
In Playback: Tap to scroll through images on the
screen.
In Settings:
Tap to
scroll through menus and submenus
.
Left | Self Timer
In Photo: Tap to change the self timer settings.
In Settings: Tap to change the submenu.
In Playback:
Tap to view the
previous
image.
Right | Exposure
In Video or Photo: Tap to change the exposure
settings.
In Settings: Tap to change the submenu.
In Playback:
Tap to view the next image.
Menu Tap to show the settings available in each mode.
Shutter In Photo: Tap to capture a photo.
Record In Video: Tap to start and stop recording.
Playback Tap to enter playback mode.
Delete In Video or Photo: Tap to delete the last recorded video
or captured image.
ISO In Video or Photo: Tap to change the ISO settings.
Display In Video or Photo: Tap to turn the icons on the LCD
screen off, turn off the LCD screen, or turn it back on.
Scene Dial Rotate the dial to switch the different scene modes.
Tripod Mount
Mount port for attaching to a
tripod nut.
Battery Door Door to cover the battery compartment and memory card
slot.
Lens Front capture device for all video and photo.
1. About Your Camera

8
2.
First Use
2.1
To Open the Battery Door
Unlock the battery door by sliding the battery door notch away from the
opening. Use a fingernail or other pointy object when sliding the latch to get
a better grip.
2.2
Installing the Battery
Insert the lithium-ion battery into the battery compartment with the metal
contacts facing the inside of the camera. The battery can only be inserted
one way.
2.3
Installing the Memory Card
Insert the included Micro SD memory card to record and store your videos
and photos. When the battery is low, media stored on the memory card will
not be erased. Please insert the SD memory card by following the steps
below:
1.
Open the battery door by following the diagram above.
2.
Insert the memory card. Ensure that the metal contacts are inserted first.
Push the memory card down until you hear an audible click.
The memory card can only be inserted in one way. Do not force the
card in if it will not go in smoothly.
3.
Close the battery door by pushing it down and sliding the lock back into
place.

9
4.
To remove the memory card, simply push in and the card will eject back
out.
NOTE: After closing the battery door, make sure that the door is
closed securely and the lock engaged.
2.4
Charging the Battery
Connect your camera to the included AC adaptor with the USB cable
provided for charging. Insert the small end of the USB plug into the camera s
port under the battery door, and the larger end in to the included AC adaptor.
While charging the LED indicator light will light up solid red, when finished
charging the light will turn off.
NOTE:
Please format the memory card before using the camera
(Caution, this will erase all data on the card).
Do not remove or insert the memory card when recording. It
may damage the card or cause data loss.
Memory card rating must be or above.

10
2.5
Powering the Camera On/Off
Press and hold the POWER button for 3 seconds to power the camera on.
To power the camera off, press the POWER button again.
If the camera
screen and it will automatically shut down within a few seconds to prevent
memory corruption or loss.
2.6
Switching Modes
Press the MODE/OK button to cycle between Photo, Interval Photo,
Video, Slow Motion, Loop Recording and Timep Lapse Modes. The
corresponding mode will be displayed in the top left corner of the screen.
2.7
Connecting to a Computer
Your camera can connect to a computer to transfer photo and video files for
viewing and editing, you can also use the camera as a webcam or you can
use your computer to charge the camera. Once connected and powered on,
the camera show M and
PC camera
Press the MODE/OK to select your desired mode.
2.8
Scene Dial
produce the best image for that selected scene. In Photo mode, simply
rotate the dial to switch scene modes, the scene modes available are below.
Sports Landscape
Portrait
Night
Macro
Photo
Burst
Auto
Beach

11
2.9
Flash
To raise the flash, simply lift the bottom edge of the flash on the front up. To
lower the flash, simply push the flash down.
2.10
Using the Zoom Function
This camera has a digital zoom function. To operate the zoom function,
slide the ZOOM button to the right to zoom in closer to the subject, and slide
the ZOOM button to the left zoom away from the subject.

12
2.11
Screen Icons
The meaning of the icons shown on the LCD screen in each mode can be
found below.
Icon
Description
Photo Mode
Interval Photo Mode
Video Mode
Slow Motion Mode
Loop Recording Mode
Time Lapse Mode
Photo Burst Mode
Photo Size (Resolution)
Movie Size (Resolution)

13
White Balance
Exposure
Metering
Sharpness
Flash
ISO
Video Quality
Record Audio
Self Timer

14
Memory Card Inserted
Scene Mode

3. Using Your Camera
15
3.
Using the Camera
3.1
Photo Shooting
Power the camera on and it will be ready to take pictures right away. You
may press the MODE/OK button to switch to another mode.
1.
Line up your shot by looking at the LCD screen to see what is in the shot.
2.
Hold the camera steady and press the SHUTTER button to capture a
photo.
3.
The number of photos that can be captured at a particular resolution will
be displayed in the top right corner of the screen.
4.
Memory Full een if there is no SD
Memory Full
will be shown on the screen when the SD card is full.
5.
The number of remaining photos is determined by the selected photo
resolution. The higher the photo resolution, the lower the number of
photos you are able to be save to the memory card. Before capturing any
photos, you can select a preferred photo resolution.
3.1.1
Photo Size
This function sets the photo resolution. The higher the resolution, the greater
the photo quality and the larger the file size of the photo.
1.
In Photo Mode press the MENU button.
2.
Select the Camera icon on the top of the left side of the screen using the
UP or DOWN buttons.
3.
Press the RIGHT button to enter the settings menu.
4.
Select Photo Size using the UP or DOWN buttons and press the
MODE/OK button to enter the menu.
5.
Use the UP or DOWN buttons to navigate the menu, and press the
MODE/OK button to confirm your selected resolution (48MP, 40MP,
30MP, 24MP, 18MP, 12MP).
6.
Press the MENU button to exit the settings menu without making a
selection.
3.1.2
White Balance
White Balance changes the color of light in your pictures, making it seem
warmer or cooler depending on how the light you're shooting in affects the
frame.
1.
In Photo Mode press the MENU button.
2.
Select the Camera icon on the top of the left side of the screen using the
UP or DOWN buttons.
3.
Press the RIGHT button to enter the settings menu.
4.
Select using the UP or DOWN buttons and press the

3. Using Your Camera
16
MODE/OK button to enter the White Balance menu.
5.
Use the UP or DOWN buttons to navigate the menu, and press the
MODE/OK button to confirm your selected option (Auto, Sunny, Cloudy,
Incandescent, Florescent).
6.
Press the MENU button to exit the settings menu without making a
selection.
3.1.3
Exposure
This function adjusts the frame brightness in your photograph.
1.
In Photo Mode press the MENU button.
2.
Select the Camera icon on the top of the left side of the screen using the
UP or DOWN buttons.
3.
Press the RIGHT button to enter the settings menu.
4.
Select using the UP or DOWN buttons and press the
MODE/OK button to enter the menu.
5.
Use the UP or DOWN buttons to navigate the menu, and press the
MODE/OK button to confirm your selected option (-3, -2, -1, 0, +1, +2,
+3).
6.
Press the MENU button to exit the settings menu without making a
selection.
3.1.4
Metering
Metering mode refers to the way in which a camera determines the appropriate
exposure (quantity of light reaching the camera lens). Spot metering will only
base the exposure setting on a very small area of the scene. Center metering
will use the light from the center of the LCD and the Multi setting measures the
light at several points on the screen.
1.
In Photo Mode press the MENU button.
2.
Select the Camera icon on the top of the left side of the screen using the
UP or DOWN buttons.
3.
Press the RIGHT button to enter the settings menu.
4.
Select using the UP or DOWN buttons and press the
MODE/OK button to enter the menu.
5.
Use the UP or DOWN buttons to navigate the menu, and press the
MODE/OK button to confirm your selected option (Multi, Center, Spot,
Matrix).
6.
Press the MENU button to exit the settings menu without making a
selection.
3.1.5
Sharpness
This function adjusts the visible detail of a photograph.

3. Using Your Camera
17
1.
In Photo Mode press the MENU button.
2.
Select the Camera icon on the top of the left side of the screen using the
UP or DOWN buttons.
3.
Press the RIGHT button to enter the settings menu.
4.
Select using the UP or DOWN buttons and press the
MODE/OK button to enter the menu.
5.
Use the UP or DOWN buttons to navigate the menu, and press the
MODE/OK button to confirm your selected option (Sharp, Normal, Soft).
6.
Press the MENU button to exit the settings menu without making a
selection.
3.1.6
Flash
This function allows to change the flash settings.
1.
In Photo Mode press the MENU button.
2.
Select the Camera icon on the top of the left side of the screen using the
UP or DOWN buttons.
3.
Press the RIGHT button to enter the settings menu.
4.
Select Flash using the UP or DOWN buttons and press the MODE/OK
button to enter the menu.
5.
Use the UP or DOWN buttons to navigate the menu, and press the
MODE/OK button to confirm your selected option (Auto, Off, On).
6.
Press the MENU button to exit the settings menu without making a
selection.
3.1.7
ISO
This function adjusts the light sensitivity in your photograph.
1.
In Photo Mode press the MENU button.
2.
Select the Camera icon on the top of the left side of the screen using the
UP or DOWN buttons.
3.
Press the RIGHT button to enter the settings menu.
4.
Select using the UP or DOWN buttons and press the MODE/OK
button to enter the menu.
5.
Press the UP or DOWN buttons to navigate the menu, and press the
MODE/OK button to confirm your selected option (ISO Auto, 100, 200,
400, 800, 1600, 3200, 6400).
6.
Press the MENU button to exit the settings menu without making a
selection.
3.1.8
Time Stamp
This setting allows you to imprint a date & time onto your captured image
files. Once an image file is captured with the imprint, the imprint cannot be

3. Using Your Camera
18
removed.
1.
In Photo Mode press the MENU button.
2.
Select the Camera icon on the top of the left side of the screen using the
UP or DOWN buttons.
3.
Press the RIGHT button to enter the settings menu.
4.
Select Time Stamp using the UP or DOWN buttons and press the
MODE/OK button to turn the time stamp on or off.
3.1.9
File Compression
Video compression is the process of reducing the number of bits needed to
record a video without compromising its visual quality. The purpose of
compression is to make a video file occupy less space than the original file
while maintaining a high quality.
Videos are compressed using codecs. Video codecs are the compression
component of video compression software that compile files by encoding the
data they contain. For the highest quality, select High Compression. For the
best compatibility across all playback devices, select H.264. Either select will
process high quality video file in MP4 format.
1.
In Photo Mode press the MENU button.
2.
Select the gear icon on the bottom of the left side of the screen using the
UP or DOWN buttons.
3.
Press the RIGHT button to enter the setup menu.
4.
Select File Compression using the UP or DOWN buttons and press the
MODE/OK button to enter the File Compression menu.
5.
Press the UP or DOWN buttons to navigate the menu, and press the
MODE/OK button to confirm your selected option (H.264, High
Compression).
6.
Press the MENU button to exit the settings menu without making a
selection.
3.1.10
Image Rotation
This option will flip the image on the LCD screen 180 degrees.
In Photo Mode press the MENU button.
Select the gear icon on the bottom of the left side of the screen using the
UP or DOWN buttons.
Press the RIGHT button to enter the setup menu.
Select Image Rotation using the UP or DOWN buttons and press the
MODE/OK button to turn on or off.

3. Using Your Camera
19
3.1.11 Frequency
This function sets the frequency of the camera from 50Hz to 60Hz. Please
check the frequency of your location and set accordingly.
1.
In Photo Mode press the MENU button.
2.
Select the gear icon on the bottom of the left side of the screen using the
UP or DOWN buttons.
3.
Press the RIGHT button to enter the setup menu.
4.
Select using the UP or DOWN buttons and press the
MODE/OK button to enter the Frequency menu.
5.
Press the UP or DOWN buttons to navigate the menu, and press the
MODE/OK button to confirm your selected option (Auto, 50 Hz, 60 Hz)
the default frequency for the United States is 60Hz.
6.
Press the MENU button to exit the settings menu without making a
selection.
3.1.12 LED Indicator
This function allows you turn the LED status indicator on and off.
In Photo Mode press the MENU button.
Select the gear icon on the bottom of the left side of the screen using the
UP or DOWN buttons.
Press the RIGHT button to enter the setup menu.
Select using the UP or DOWN buttons and press the
MODE/OK button to turn the on or off.
3.1.13 Screen Saver
This function sets the duration of time in which the camcorder will wait with
no user input before automatically turning off the LCD screen. Note: even
while the screen is off, the camera will still be powered on.
1. In Photo Mode press the MENU button.
2. Select the gear icon on the bottom of the left side of the screen using the
UP or DOWN buttons.
3. Press the RIGHT button to enter the setup menu.
4. Select Screen Saver using the UP or DOWN buttons and press the
MODE/OK button to enter the Screen Saver menu.
5. Press the UP or DOWN buttons to navigate the menu, and press the
MODE/OK button to confirm your selected option (Off, 30 Seconds, 1
Minute, 2 Minutes, 10 Minutes).
6. Press the MENU button to exit the settings menu without making a
selection.