MIP MED-I-CART 2000 User manual

Assembling frame
2, 3 & 4 BAG LINEAR CART DESIGNS
Side
frame
Accessory
bar
Base
frame
MED-I-CART 2000
ASSEMBLY INSTRUCTIONS
We are pleased to introduce the Med-I-Cart 2000
Before assembly, we suggest you read the following instructions
In order to familiarize yourself with the parts and their names.
Your assembly kit includes:
STEP ONE
STEP TWO
?Spread open shipping carton on the floor, use as protective mat during assembly. Remove
wrapping from all parts.
Slide cart side frames into cart base as shown at right.
?To insert accessory bars, pull side frames outward and insert them one end at a time.
?Turn cart upside down
Make sure that side frames are fully inserted. Note: Side frames must protrude past base
frame.
?Insert bumpers
Insert wheel into shaft. Push firmly or gently tap with hammer. Two of the wheels come
with brakes. We suggest that these both be put at the front of the cart so that they are
easily positioned for use. .
Bumper
Base
Stem
Shaft
Installing wheels
Cart base
Cart side frames
Accessory bars
Bag frames
Plastic lids
Wheels/casters
Bumpers
LC/2000-2 LC/2000-3 LC/2000-4
1
2
2
2
2
4
4
1
2
2
3
3
4
4
1
2
2
4
4
4
4
?Using holes on side frames, align pins under fitting lip and snap on
Make sure that all lide stoppers face the same direction
?Snap on lids. The handle should face the direction opposite from the lid stoppers
Attaching bag frames and lids
STEP THREE
Bag holder
hooks
Hook for
MIP bag
retaining system
Lid stoppers
Fitting
lip

INSTALLING OPTIONAL
BAG RETAINING SYSTEM
Lid
Bag frame
Plastic loop
Nipple
9100 Ray Lawson blvd , Anjou, Québec
H1J 1K8
Tel.: [phone] Fax: [phone]
Toll free (US & CANADA) [phone]
E-Mail: [email protected]
site web: www.mipinc.com
?Attach small end of tubing onto nipple protruding from back of lid
First install bag on bag frame. Then stretch
tubing over bag and use hooks on bag frame
to maintain tubing in place. When not in use,
tubing should be hanging from back of lid.
Installing foot pedal system
The foot pedal system can be installed on all of our carts including the LC-2000 series. Older carts might have inappropriate lids. The
appropriate ones have an embossed Med-I-Cart logo. If this not the case, contact our customer service department, they will provide you
with a free lid for every purchase of our foot-pedal system.
Parts included:
Foot pedal
Lifting
rod Lid lift
lever Foot pedal retaining clip
Tools required: Drill with 5/32” (4mm) bit; screwdriver; felt tip marker;
pair of pliers
?Begin with assembled cart. Do not
install lid immediately.
a. Insert bottom end of rod in the slot
of the pedal b. It will be a tight fit c.
Lift rod as indicated.
b. c.
?a) Position the pedal underneath the cart. Clip it on the
central bar of the cart base b) Position the pedal so that the
lifting rod is 1/4” (6mm) away from the bag frame. Make
sure that the rod is on the same side as the lid stoppers on
the bag frame.
?b)
a)Place lid lift lever under side frame close to bag frame
b) Insert top extremity of the lifting rod into the lift lever’s
hole c) Clip the lid over the lift lever. Push lid lift lever to
the lid.
Use a marker to indicate where you should drill b. Move
the lid lift away for easier access. A 5/32” (4 mm) bit is
required on your drill. After drilling push the lid lift lever
back to the lid. Note: Do not mark holes with lids off.
Alignement might be incorrect.
?a)
c)
a) b)
?Push the bolt through the
lid and the lid lift lever,
screw the nut on. Using a
pair of pliers to hold the
nut, tighten it using a
screwdriver.
?Position the foot pedal
retainer clip into recessed
space. Attach with two screws.
Only tighten enough to insure
that screws are fully inserted
in plastic. Overtightening
might strip plastic.