Mirabella International Mirabella Genio User manual

I005282 Mirabella Genio
30cm Pixel LED Twin Bar
USB powered
Please read this manual carefully before using the
product and keep it for future reference.

Product Specification
If you don’t have Wi-Fi at home or cannot pair it for some reason but still
want to use this light, simply wait for 3 minutes for the light to stop blinking,
then manually press Cbutton on Wi-Fi controller to change colour and modes

Product Installation
Please pay attention to HOW you insert the light to the base, incorrect
installation will bend the power cord and make the light bar unstable.

1. Wi-Fi Connection Preparation
Your phone must be connected to 2.4Ghz Wi-Fi and not to the 5GHz, To verify
your mobile phone is connected to
the 2.4Ghz Wi-Fi network, Navigate to
the Setting menu and click on
Wi-Fi. In this menu you will see all
detectable networks in your area.
Locate the SSID for your network,
select the Wi-Fi SSID that does NOT
end with 5GHz. (refer to the image).
Check you have a strong Wi-Fi signal
(at least two bars) in the location
where the smart device is to be
installed.
If you don’t have at least two bars
signal on your phone, then you may need to reconsider the location or getting
a Wi-Fi extender to boost the Wi-Fi signal strength.
If you have dual band router but you don’t see two Wi-Fi name SSID’s, one
with 5G and one without 5G, you MUST log into the router and manually
disable the 5Ghz Wi-Fi signal. if you’re having connection issues. Please
contact your internet provider on how to disable 5Ghz Wi-Fi for your router or
check our website FAQ section. www.mirabellagenio.com.au
Install the APP and register Account
For the best experience, download the "Mirabella Genio" APP to your
smartphone from the App Store or Google Play, The APP icon will be displayed
after it’s installed successfully
Bluetooth pairing assistant function
Our latest genio smart Wi-Fi range has a Bluetooth pairing assistant function,
to make the pairing even easier than before, to take advantage of this
function, please turn on the Bluetooth function on your phone, insert the USB
cable to a standard USB port or 5V 1A USB charger, wait for the light starts to
blink red rapidly (2 blinks per second)

If it does not automatically start to blink rapidly when first powered on, press
and hold the ON/OFF button on the Wi-Fi Controller and wait for the light to
start blinking RED
Open Mirabella genio APP, tap on + , wait for the APP to automatically
discovery the smart device , please ensure that you are using the 2.4Ghz Wi-Fi
name and password, do not use the Wi-Fi Name ending -5G

If the Bluetooth method does not work, please turn off Bluetooth
on your phone and use the EZ method to pair – when the light is
fast blinking RED (2 blinks per second)
1. Connect the USB cable end to the USB port, wait a few seconds, light
will commence blinking RED rapidly (2 blinks per second)
2. If it does not automatically start to blink rapidly when first powered
on, press and hold the ON/OFF button on the Wi-Fi switch controller,
until the light starts to blink rapidly (2 blinks per second)
3. Open Mirabella Genio APP, tap on + symbol, add device then
Ambient Lighting choose Genio 30cm Bar Light from the list
4.Enter your 2.4Ghz Wi-Fi name and password, (make sure Wi-Fi name
doesn’t end with -5G)
Follow the APP’s instructions carefully to complete the network pairing
process.

if the fast-blinking method (EZ method, mentioned above) doesn’t
work for you, please try the slow blinking (AP method) below.
While the Bar light is rapidly blinking, press and hold the pairing button on the
Wi-Fi controller again and then wait for the light to start blinking slowly (1
blink per every 2 seconds)
Open up the Mirabella genio APP, tap on + , add device then choose Genio
30cm bar Light from the Ambient Lighting list
Enter your 2.4Ghz Wi-Fi name and password, (make sure the Wi-Fi name
doesn’t end with -5G), then in reset the device first screen tap on EZ mode (in
the Top right hand corner just below the your phone’s battery icon),
select AP Mode (refer to the 1st and 2nd image below) Now Confirm indicator
slowly blinking (refer to image 3),
hit Next, then Go to connect and connect to Wi-Fi named SmartLife_XXXX

Note: If you would not see Wi-Fi name beginning with the word
SmartLife_XXXX then the device is not slowly blinking, please reset and
ensure that it is slowly blinking.
Once connected to SmartLife_XXXX, return to the Mirabella Genio APP and it
will commence adding device

FAQ:
Q. I have internet/power outage and device went offline and doesn’t reconnect back
online by itself?
A. Go the light settings page (… or pencil looking icon), look for “remove
device” Remove it and reset the device and pair it again through the app.
Mirabella International Pty Ltd
1 Mirabella Drive Tullamarine VIC. 3043 Australia
t: 1800 636 528
e: [e-mail]