MIRABELLA Genio I003935 User manual

I003935MirabellaGenioWi‐FiSmartBackgroundLight

TOENSURETHESAFEANDSATISFACTORYOPERATIONOFTHISSETPLEASEREADTHESEINSTRUCTIONSCAREFULLY
ANDRETAINFORFUTUREREFERENCE 
SAFETYINFORMATION: 
•Removesetfrompackagingbeforeconnectingtoapowersupply. 
•Pleasenotethatwerecommendthisproductbepoweredwithastandard5V2AUSBadaptor(notincluded).
Poweringthisunitwithanadaptorsmallerthana2Aratingmaycauseflickering. 
•Ensurethatthecableiscompletelyuncoiledwhilstsetisinuse. 
•LEDbulbsarenon‐replaceable. 

PRODUCTINSTALLATION 














When tightening the bolt to the metal sleeve, do not
tighten,ensurethatthereisagapofatleast3mm.This
willallowthelamptowertoslideintoposition.
Oncethelamptowerisinposition,Tightenthenutto
lockthetower. 






TheLamptowercanbeorientatedeither
VerticallyorHorizontally.

WhenconnectingthelamptowerstotheWi‐Ficontroller,makesurethearrowsarealignedwitheachother.

Wi‐Fipairinginformation(BK,EZandAPmethod)
1. Download“MirabellaGenio”AppfromtheAPPstoreorGooglePlayandregisteranaccount. 
2. Connectyourmobilephoneto2.4GHzWi‐Finetwork.(Pleasenote,thatthisunitdoesnotsupport5GHzWi‐Fi)
3. ConnecttheUSBcabletoastandardUSBportorUSBadaptor(musthave5V2Aorgreateroutput)
4. Waitforthelighttocommencetoblink. 

Ifthebackgroundlightdoesnotstarttoblinkwhenfirstpoweredon,powerofftheunitbyunpluggingtheUSBfrom
powersource,thenpoweritonagainbypluggingtheUSBbackintopowersource.
PressandholdtheON/OFFbuttonontheWi‐Ficontroller,untilitstartstoblink.

BluetoothBKmethod
OurlatestgeniosmartWi‐FilightingrangehasaBluetoothpairingassistfunction,totakeadvantageofthisfunction,please
ensurethatheBluetoothonyourphoneisturnedon.  
Makesurethelightisblinkingfast(2blinkspersecond),OpenMirabellaGenioapp,tapontheplussymbol  , 
TheAPPwillnowautomaticallyfindthelights,oncetheappidentifiesthelights,followtheinstructionsbelowfinalisethe
pairingofthelightstotheApp.

FastingblinkingEZmethod(whentheBluetoothonthephoneisturnedoff)
1. OpentheMirabellaGenioapp,tapontheplussymbol. 
2. SelectGenioTubelightunderthesmartlighting,thenfollowthein‐apppromptstoconnecttubelighttoyourapp



SlowblinkingAPmethod(1blinkingper2second)
Ifthefastingblinkingmethoddidn’tworkforyou,pleasetrytheslowblinkingAPmethod.
Whilethelightisfastblinking,pressandholdtheON/OFFagainandwaitforthelighttostartblinkingslowly(1blinkper
second). 
1. OpentheAPPthistimeontheresetthedevicefirstscreen. 
2. TaponEZmodelocatedinthetoprighthandcornerofthescreen,selectAPMode.
3. NowConfirmindicatorslowlyblinking,tapNext,thenGotoconnect.Theappshouldautomaticallytakeyouto
yourWi‐Fiscreen,ifitdoesnotgetoutoftheGenioappandgointoyourphoneWi‐Fiscreenpage.
4. SearchforaWi‐FisignalcommencingwithSmartLife_XXX,oncefoundselectittocompletethepairingprocess.
5. 


IfyoucannotseetheSmartLife‐xxxxonthelist,it
meansthelightwasnotblinkingslowly,pleasereset
itandtryagain.




AfteryouhaveconnectedtoSmartLife_XXXX,returnbacktotheMirabellaGenioappanditwillcommence 
the0‐100%countdownandconnectionprocess,oncecomplete,yourlightsarenowpairedtotheapp. 

Pleasepayattentiontothisscreen
todetermentthecauseoftime‐out
error
Ifthelightneverstopsblinking,
therecouldbeissuewiththeWi‐Fi
controller,pleasecheckouronline
FAQpagebeforereturningit 

iflightstoppedblinking,butunable
progressto“registeroncloud”it
indicatescommunicationerrorwith
yourroutertoourcloudservice 
please check our online FAQ page
and ensure.
1.Youenterthecorrect2.4GHzWi‐
Finameandpassword 
2.Wi‐Ficontrollerisinalocation
withgoodWi‐Ficoverage,trymove
itclosertotherouter 
3.5GhzWi‐Fisignalisturnedoffon
therouter(canbeturnonafterthe
deviceisconnected)
4.ifyouareusingIOS14,please
ensure“localnetwork”permission
isturnedonforGenioAPP

FAQ:
Q.Ihaveinternet/poweroutageanddevicewentofflineanddoesnotreconnectbackonlineby
itself? 
A.Gothedevice’settingspage(pencilor...icon),lookfor“removedevice”Removeitandresetthedevice
andpairitagainthroughtheapp.

IfyoustillhavingissuewithpairingafteruseAPmethod,pleasecheckouronlineFAQpageson
www.mirabellagenio.com.au/faqs
Mirabella International Pty Ltd
1 Mirabella Drive Tullamarine VIC. 3043 Australia
t: 1800 636 528
e: [email protected]