MIRABELLA Genio I004560 User manual

I004560 Mirabella Genio Wi-Fi Pixel Oval Floor Lamp
Item # I004560
TO ENSURE THE SAFE AND SATISFACTORY OPERATION OF THIS SET PLEASE READ THESE INSTRUCTIONS CAREFULLY
AND RETAIN FOR FUTURE REFERENCE
SAFETY INFORMATION:
• Remove set from packaging before connecting to a power supply.
• only use the adaptor that is supplied.
•Ensure that the cable is completely uncoiled whilst set is in use.
•LED bulbs are non-replaceable.
PRODUCT INSTALLATION

When connecting the Floor lamp to the Wi-Fi controller, make sure the arrows are aligned with each other.
Wi-Fi pairing information (BK, EZ and AP method)
1. Download “Mirabella Genio” App from the APP store or Google Play and register an account.
2. Connect your mobile phone to 2.4GHz Wi-Fi network. (Please note, that this unit does not support 5GHz Wi-Fi)
3. Connect the Wi-Fi controller to the light, and the adaptor to the Wi-Fi controller
4. Wait for the light to commence to blink.
If the Floor light does not start to blink when first powered on, Press and hold the ON/OFF button on the Wi-Fi
controller, until it starts to blink.
If you having difficulty connect this
lamp to the Genio APP, wait for 3
minutes and lamp stopped working,
you can control this lamp manually
using the 3 button Wi-Fi controller.
Bluetooth BK method
Our latest genio smart Wi-Fi lighting range has a Bluetooth pairing assist function, to take advantage of this function, please
ensure that he Bluetooth on your phone is turned on.
Make sure the light is blinking fast (2 blinks per second), Open Mirabella Genio app, tap on the plus symbol ,
The APP will now automatically find the lights, once the app identifies the lights, follow the instructions below finalize the
pairing of the lights to the App.

Fasting blinking EZ method (when the Bluetooth on the phone is turned off)
1. Open the Mirabella Genio app, tap on the plus symbol.
2. Select Genio Tube light under the smart lighting, then follow the in-app prompts to connect tube light to your app
Slow blinking AP method (1 blinking per 2 second)
If the fasting blinking method didn’t work for you, please try the slow blinking AP method.
While the light is fast blinking, press and hold the ON/OFF again and wait for the light to start blinking slowly (1 blink per
second).
1. Open the APP this time on the reset the device first screen.
2. Tap on EZ mode located in the top right hand corner of the screen, select AP Mode.
3. Now Confirm indicator slowly blinking , tap Next, then Go to connect. The app should automatically take you to
your Wi-Fi screen, if it does not get out of the Genio app and go into your phone Wi-Fi screen page.
4. Search for a Wi-Fi signal commencing with SmartLife_XXX, once found select it to complete the pairing process.

5.
If you cannot see the SmartLife-xxxx on the list, it
means the light was not blinking slowly, please reset
it and try again.
After you have connected to SmartLife_XXXX, return back to the Mirabella Genio app and it will commence
the 0-100% countdown and connection process, once complete, your lights are now paired to the app.
Please pay attention to this screen
to determent the cause of time-out
error
If the light never stops blinking,
there could be issue with the Wi-Fi
controller, please check our online
FAQ page before returning it
if light stopped blinking, but unable
progress to “register on cloud” it
indicates communication error with
your router to our cloud service
please check our online FAQ page
and ensure.
1. You enter the correct 2.4GHz Wi-
Fi name and password
2.Wi-Fi controller is in a location
with good Wi-Fi coverage, try move
it closer to the router
3. 5Ghz Wi-Fi signal is turned off on
the router (can be turn on after the
device is connected)
4. if you are using IOS 14, please
ensure “local network” permission
is turned on for Genio APP

FAQ:
Q. I have internet/power outage and device went offline and does not reconnect back online by
itself?
A. Go the device’ settings page (pencil or ... icon), look for “remove device” Remove it and reset the device
and pair it again through the app.
Q. the light doesn’t light up?
A. please make sure when connect the Wi-Fi controller, the arrows are point at each other
Also try using known working 12V DC 2A adaptor
If you still having issue with pairing after use AP method, please check our online FAQ pages on
www.mirabellagenio.com.au/faqs
Mirabella International Pty Ltd
1 Mirabella Drive Tullamarine VIC. 3043 Australia
t: 1800 636 528
e: [e-mail]