MIRAN FoCol A30 Arc User manual

323075IS 03-07-2022
SHEET 1 OF 14
Carefully read the contents of these instructions, as the
instructions indicate the correct step by step procedure
to assemble the product. The carton contents page(s) will
identify the assembly part numbers and their descriptions.
Before proceeding with the assembly process, match the
carton contents to the stated contents to ensure there are
no missing parts. In the event of assembly problems or
missing parts, please call our customer service department
at 616-842-5330.
CAUTION:
ASSEMBLED UNIT IS VERY HEAVY. DO NOT ATTEMPT TO
LIFT OR MOVE WITHOUT ASSISTANCE.
THE MANUFACTURER OF THIS DISPLAY ASSUMES
NO LIABILITY FOR INJURY CAUSED BY IMPROPER
ASSEMBLY / INSTALLATION OF THIS DISPLAY.
This product contains chemicals known to
the State of California to cause cancer and
birth defects or other reproduction harm.
WARNING:
For more information, go to www.P65Warnings.ca.gov
TOOLS
• Socket Wrench
CONCENTRATE FOCOL SHOWN
2 PEOPLE NEEDED TO ASSEMBLE
FoCol

323075IS 03-07-2022
SHEET 2 OF 14
FoCol • Arcs
A30 Arc A60 Arc A90 Arc

323075IS 03-07-2022
SHEET 3 OF 14
FINISHED END KIT CONTENTS
(3) brackets (top,
middle, & bottom)
(2) nished end pieces
(2) felt slat
(1) bottom support
(3) brackets (top,
middle, & bottom)
TRANSITION KIT CONTENTS
FoCol • Kits
NOTE: E60 FINISHED END KIT AND T60 TRANSITION KIT SHOWN.

323075IS 03-07-2022
SHEET 4 OF 14
FoCol • Hardware
1/4-20 X 1-1/4” HEX HEAD
SCREW-BLACK
1/4-20 X 5/8” HEX HEAD
SCREW-BLACK

323075IS 03-07-2022
SHEET 5 OF 14
FoCol • Attaching/Detaching Felt Slat
Detach upper felt ap
from magnet. Lift felt slat straight up to
detach from bracket.
To reattach felt, slide slat
into slotted brackets and
reattach top and bottom
aps to magnets.
Detach lower felt ap
from magnet.
AC
B
A
C
B

323075IS 03-07-2022
SHEET 6 OF 14
FoCol • Attaching an Arc
Remove felt slat from
back end of arc.
REFER TO SHEET 5
Remove (6) screws from
right side and set wood
n aside.
A
B
B

323075IS 03-07-2022
SHEET 7 OF 14
FoCol • Attaching an Arc
Use dowels to align arcs to
wood n. Attach from the
right side using previously
removed screws.
C
C
Reapply felt slats
to arcs.
REFER TO SHEET 5
D

323075IS 03-07-2022
SHEET 8 OF 14
FoCol • Attaching an Arc
Continue to attach
appropriate arcs to
build desired FoCol
congurations using
previous steps.
E

323075IS 03-07-2022
SHEET 9 OF 14
FoCol • Attaching Finished Ends
Remove end felt slat
from brackets.
REFER TO SHEET 5
A
B
C
Attach nished end with felt
using the 1 1/4” screws from
the end of the arc.
Attach single nished end
from kit using provided 5/8”
screws.
B
C

323075IS 03-07-2022
SHEET 10 OF 14
FoCol • Attaching Finished Ends
Reapply felt slats
to arcs.
REFER TO SHEET 5
D

323075IS 03-07-2022
SHEET 11 OF 14
FoCol • Attaching Transition Kit to Change Arc Direction
Remove end felt slat
from end piece.
Remove brackets from arc end and
replace with brackets from transition kit.
Transition brackets will need to be rotated
180 degrees to create direction change.
Transistion
Panel
REFER TO SHEET 5
A B
*USE WHEN CHANGING DIRECTION OF ARC

323075IS 03-07-2022
SHEET 12 OF 14
FoCol • Attaching Transition Kit to Change Arc Direction
Screw transition brackets into
conjoining bracket weld nuts.
If weld nuts are not present in
conjoining bracket, use provided
nuts to fasten.
*USE WHEN CHANGING DIRECTION OF ARC
C
C

323075IS 03-07-2022
SHEET 13 OF 14
FoCol • Attaching Transition Kit to Change Arc Direction
EXAMPLE OF GROUP FOCOL SHOWING MULTIPLE TRANSITIONS IN GREY

323075IS 03-07-2022
SHEET 14 OF 14
FoCol • Congurations
CONCENTRATE
(3) A30 ARCS
(3) A60ARCS
WORK
(3) A30 ARCS
GATHER
(4) A90 ARCS
GROUP
(5) A60 ARCS
HUDDLE
(9) A60 ARCS