Ergolux ELSTD1MTMBA User manual

STANDING DESK
ELECTRIC SINGLE MOTOR
MEMORY
ELSTD1MTMBA & ELSTD1MTMWA

2
Safety & Warnings
3
Components
5
Overview
7
Assembly
9
Operation
17
Specifications
19
Troubleshooting
20
Notes
21

3
• Read all instructions before use and retain this user guide for future reference.
• Read all following safety precautions carefully before use.
• Your equipment is intended for use in cool, dry conditi o n s . You should avoi d storage in
extreme cold, hot or damp areas as this may lead to corrosion and other related
problems.
• This desk is designed for indoor use only.
• Do not modify the desk frame or any of the components that operate this desk in any
way.
• If the power cord is damaged, cease use immediately and contact help.Kogan.com for
support.
• If the control box emits any abnormal noises or strong odours, cease use immediately
and contact help.Kogan.com for support.
• Ensure any obstacles are removed from the area around the desk during assembly and
operation.
• Ensure that all cords and wires are arranged in a way where they are not a tripping
hazard.
• Unplug the power cord before cleaning. Wipe the dust from the surface using a slightly
damp cloth. Ensure any water does not come in contact with any internal parts or
connectors.
• Do not disassemble or perform any maintenance without disconnecting the power first.
• Do not use any corrosive or abrasive materials to clean the product.
• The control box contains electronic components, metals, plastics, wires etc. ensure it is
disposed of in accordance with your local environmental legislation. Do not dispose
with general household waste.
• Ensure this product is completely and correctly assembled before use.
• Be familiar with all functions and program settings of the product before first use.
• This product can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
• Children should not be allowed play with this product.
• Cleaning and user maintenance should not be performed by children without
supervision.
• Retain the original packaging where possible, to use for any future transportation of this
product.
SAFETY & WARNINGS

4
• Power supply: AC100V-240V,50/60HZ
• Service Environment: 0-40°C
• Slight noise caused by the V-ribbed belt or brake system due to structure will not have
any effect on the use of the equipment.

5
Lay all components out on a clean floor and ensure all parts are included. If any pieces are
missing, check all packaging thoroughly, then contact help.Kogan.com for assistance.
1Feet (x2)
2Column
3Column (with motor)
4Support beam
5Tr a n s m i s s i o n r o d
6 Supporting plate (x2)
7Control box
8 Baffle (x2)
9 Controller
10 Power cord
11 Cable tie (x4)
COMPONENTS

6
Hardware List
AM6 Hex Screw
(x12)
BM8 Hex Screw
(x4)
C4mm & 5mm Allen
Key (x2)
D2.5mm Allen
Key
EM4 Hex Screw (x4)
FST4.2 Screw (x15)
GWrench (x1)

7
1
Feet
7
Control panel
2
Column
8
Baffle
3
Column (with motor)
9
Hand switch
4
Supporting beam
10
Power cable
5
Transmission rod
11
Cable tie
6
Supporting plate
OVERVIEW

8
Control Panel
Adjust the desk upwards
Adjust the desk downwards
1
Position 1, first height position saved by the user
2
Position 2, second height position saved by the user
3
Position 3, third height position saved by the user
M
Height memory function
A
Alert button to remind users to shift position
Display
Raise
Lower
Position
1/2/3
Alert
Memory

9
Step 1: Install the feet
• Attach the Feet (1) to the bottom of the Lifting Columns (2 & 3) using x8 M6 Hex
Screws (A).
AM6 Hex Screw (x8)
C5mm Allen Key
ASSEMBLY
A
C
1
2
3

10
Step 2: Install supporting beam
• Loosen screws on the supporting beam (4) using the 4mm Allen key (C), then extend
the supporting beam.
• Adjust the supporting beam size (4) according to your desktop size.
C4mm Allen Key
1
Extend
4
C

11
Step 3: Install supporting beam
• Attach the supporting beam to the lifting columns (2)(3), using x2 M8 Hex Screw (B).
• Tighten screws on supporting beam with wrench 4mm Allen key (C).
BM8 Hex Screw (x2)
C4mm Allen Key
C5mm Allen Key
B
C
4
2
3
2
3
C

12
Step 4: Install Transmission rod
• Loosen the nut on the left side of the Transmission rod (5) and insert it into the lifting
column (2). Tighten the nut on the Transmission rod using the wrench (G).
• Rotate the right side of the Transmission rod (5) to insert it into the motor on the lifting
column (3). Tighten the screw on the Transmission rod using the 2.5mm Allen key (D).
Note: Do not rotate the Transmission rod more than a third of a turn.
D2.5mm Allen key
GWrench
2
5
3
Loosen
Insert
Tighten
Rotate
Insert
Tighten
G
D

13
Step 5: Install Supporting plate
• Use M8 Hex Screws (B)to attach the supporting plates (6) to the lifting columns (2)(3).
• Secure the supporting plates in place using the M6 Hex Screws (A).
AM6 Hex Screw (x4)
BM8 Hex Screw (x2)
C5mm Allen key
B
3
A
C
2
6
C
B
A
C

14
Step 6: Install Control box and Control panel
• Attach the desktop to the assembled frame using the ST4.2 screws (F) and a drill.
• Attach the control panel (9) to the front edge of the desktop using the ST4.2 screws (F)
and a drill.
• Attach the control box (9) in the position shown below using the ST4.2 screws (F) and a
drill.
FST4.2 Screw (x14)
F
7
9

15
Step 7: Install Baffle
Install the Baffles (8), using x4 M4 Hex Screws (E) and the 2.5mm Allen key (D).
EM4 Hex Screw (x4)
D2.5mm Allen key
E
8
D

16
Step 8: Connect the Cables
• Connect the Cables to the Control Box (7).
• Use the cable tie (11) to manage all the cables underneath the desktop.
10
7
11
9
Remove backing
11
11
11
Manage cables
Secure
AC
AC
Power port
Power port
Control
panel
M1
HS
DC
Motor
Control
panel
M1
HS
Motor

17
Adjusting the Height
Press the "▲" or "▼" buttons to adjust the height of the desk. The display will show the
current height.
Memory Setting
• Press "▲" or "▼" buttons to adjust the height to the desired height. Press "M" to save
the height and the screen will display " "; Press "1, 2 or 3". The height is now saved to
the corresponding position. The saved position will show in the display screen as " ","
" or " ";
• Press "1, 2 or 3" button directly to automatically adjust the memory height you saved.
Stand Reminder
• Press "A" button to activate the stand reminder function. The LED display shows " "
• 2 seconds later, press the "▲" or "▼" button to adjust the reminder time only when the
display screen flashes. The default time of the reminder is 45 minutes, which is shown
as " ".
• Press any button to save the time or wait 5 seconds and system will save the time
automatically.
• During the countdown, any operation will lead to a repeat starting of the timer. When
the countdown finishes, display screen will show “ ” the buzzer will be active and
beep for 10 seconds.
• Within the 10-second reminder, press any button to reactivate the countdown. If there
is no user input within the 10-second reminder, there will be another alarm after 5
minutes.
• If there no user input during the second alarm, the stand reminder will turn off.
• Press and hold the "A" button for 3 seconds to turn off the stand reminder. The LED
display shows " ".
OPERATION

18
Collision Avoidance
During height adjustment, if tabletop comes in contact with another object, it instantly
stops and reverses to avoid damage.
• Press and hold the “▲” “▼” buttons for 5 seconds at the same time to adjust the
collision avoidance sensitivity. Select between the 4 levels;
Setting
Sensitivity
A0
Off
A1
Low
A2
Medium
A3
High
• Press and hold the “▲” “▼” button for 5 seconds at the same time. If the display does
not display the above code, there is no anti-collision function.
Reset
When the display shows " ", press “▼”button until the desk reaches its lowest height and
rebounds to stop, it means the reset has been finished.
• If this fails and the LED shows "E01" or "E02", wait 18 minutes before resetting the desk
again.
• If the “▼” button doesn't work, check the wiring and then disconnect off the power for
at least 10 seconds. Reconnect to the power and press “▼” button to start the reset
process when it shows the display shows " "
If the above procedure fails, contact help.Kogan.com for support.

19
Column Number
2
Maximum Load
70kg
Speed
25mm/s
Input Voltage
100-240V
Lowest Position
710mm
Highest Position
1210mm
Desktop Size
1000-1600mm
500-800mm
Duty Cycle
Continuous operation for 2 mins at most after pause
for 18 mins
Applicable Temperature
0~40°C
SPECIFICATIONS

20
The following tips will help you detect and eliminate common faults. If the fault you met is
not listed below, contact help.Kogan.com for support.
Problem
Solution
No response from control panel after
connecting the power.
Check if all the cables are connected well
Contact help.Kogan.com for support.
Desk is rising very slowly.
Ensure desk is not overloaded. Max
loading: 70kg;
The motor is not operating correctly.
Contact help.Kogan.com for support.
Desk will not raise or lower.
Reposition the desk and ensure there are
no obstructions.
Contact help.Kogan.com for support.
Desk slowly lowers itself.
Ensure desk is not overloaded. Max
loading: 70kg;
Contact help.Kogan.com for support.
Contact your supplier or dealer
Overwork
(Duty cycle: Max 2min on/18min OFF).
Restart after waiting for 18mins while
connected with power.
Desk does not raise or lower enough.
Press "M" and "3" together for 3 seconds
or more, after 2 beeps are heard. The
desk has been restored to factory settings
This marking indicates that this appliance should not be disposed with
other household wastes. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources.
TROUBLESHOOTING