Mitsubishi Electric 840 Series User manual

ANT
ANT
Locations of jacks shown in the
connection diagrams. Not all
jacks shown are offered on all
models.
Pb
Pr
Y
L
R
L
R
AUDIO
OUT
Cable TV
service with
older cable box
Cable TV
service
Antenna
reception
1234
3D
GLASSES
EMITTER
ANT
HDMI
L
R
L
R
L
R
DIGITAL
AUDIO
OUTPUT
AUDIO/SURROUND
-OUTPUT-
RL
LANUSB-P
CENTER
INPUT SUB WOOFER OUTPUT
EXTERNAL
CONTROLLER
INPUT
Device with
component video
output
Device with
HDMI output
Component
video
cables
HDMII cable
Analog audio
cables
Composite
video cable
Analog
audio cables
Device with
composite
video output
Older cable box with coaxial output
Direct cable (no cable box)
Over-the-air VHF/UHF antenna
or
These two sources require a
channel scan to receive digital
channels. See instructions on
other side.
Note: Connect your
composite video connec-
tor (usually yellow) to the
TV’s green input jack.
SD
SD
SD
HD
SDHD
SDHD
SDHD
DVI-to-HDMI
cable
Analog audio cable with
stereo mini-plugs
3
Device with
digital DVI
output
4
4
2
2
24
3
1
1
1
Quick Setup Guide
V45/C11/CA/+/++/CB 853B659A10 © 2011 Mitsubishi Electric Visual Solutions America,Inc.
See important information about high-definition video on the other side.
840 Series. Additional audio connections are described in the Supplemen-
tal Owner’s Guide at www.mitsubishi-tv.com.SD
HD Carries High-Definition Video
Carries Standard-Definition Video
TV Connections Overview

Quick Setup Guide
Important Note About High-Definition TV (HDTV)
To view high-definition (HD) pictures you must use
a high-definition programming source and suitable
cable type (e.g., HDMI or component). Examples of
high-definition sources are:
• Cable service with an HD cable box
• Direct cable service without a box
• Satellite service with an HD receiver
• Blu-ray disc player
• Over-the-air antenna
Your cable TV or satellite service provider may
charge extra for high-definition service.
The TV’s Test Picture feature displays a high-
quality sample image that demonstrates the TV’s
display capabilities. Press
MENU and go to Picture >
Picture+ > Test Picture.
Setting Up Other Inputs
4. Open the Setup > Channel menu. Press ENTER.
Channel Scan for the
ANT (Antenna) Input
You must perform a channel scan to enable recep-
tion of digital channels. If you skip this step, the TV
will receive only analog channels. The scan will search
for local channels available from an antenna or direct cable
service (no cable box). Note: Direct cable service will not
include scrambled or premium channels.
5. Repeat these steps for each additional device you
want to add.
Sample
New Device
Found menu
MENU
5. Highlight Ant Air if connected to an
over-the-air antenna. Highlight Ant
Cable for service over direct cable
(no cable box). Press
ENTER to add a
check.
6. Highlight All channels. Press ENTER to add a check.
7. Highlight Scan and press ENTER .
Channel memorization may take up
to 15 minutes to complete.
EXIT
Selecting a Source to Watch
1. Press INPUT .
INPUT
Sample Input Selection menu, antenna input selected
2. Press and to highlight an input icon.
3. Press ENTER to switch to the input.
1. Power on the TV and your A/V devices.
2. Connect one device to the TV, making note of the
TV input jack.
The TV will display the New Device Found screen if
the connection type is detectable.
3. Highlight the device type in the on-screen list and
press ENTER to add a check by the device name.
The name you select here will appear in the Input
Selection menu.
4. Press EXIT to close the New Device
Found screen.
1. Power on the TV.
2. Connect the incoming coaxial
cable to the TV’s
ANT input.
3. Press MENU .