Mitsubishi CL2XY16-DTP1C5V User manual

CL2XY16-DTP1C5
V
CC-Link/LT Remote I/O Module
User's Manual
(Hardware)
Thank you very much for purchasing this product.
Please read this manual thoroughly before starting to use the product
and handle the product properly.
MODEL CL2XY16-DTP1C5V-U
MODEL
CODE 13JP27
IB(NA)-0800260-A(0308)MEE
2003 MITSUBISHI ELECTRIC CORPORATION

A-1
zSAFETY PRECAUTIONS z
(Read these precautions before using.)
Please read this manual carefully and pay special attention to safety in order to
handle this product properly. Also pay careful attention to safety and handle the
module properly.
These precautions apply only to Mitsubishi equipment. Refer to the user's
manual of the CPU module to use for a description of the PLC system safety
precautions.
These l SAFETY PRECAUTIONS l classify the safety precautions into two
categories: "DANGER" and "CAUTION".
Procedures which may lead to a dangerous condition and
cause death or serious injury if not carried out properly.
Procedures which may lead to a dangerous condition and
cause superficial to medium injury, or physical damage only,
if not carried out properly.
Depending on circumstances, procedures indicated by CAUTION may also
be linked to serious results.
In any case, it is important to follow the directions for usage.
Store this manual in a safe place so that you can take it out and read it whenever
necessary. Always forward it to the end user.
[DESIGN PRECAUTIONS] DANGER
zRefer to Chapter 3 of this manual for the operation status of the module in
case a communication error occurs in the data link.
zOutput could be switched on or off when a problem occurs in the remote I/O
modules. So build an external monitoring circuit that will monitor any output
signals that could cause a serious accident.
CAUTION
zDo not have control cables and communication cables bundled with or
placed near by the main circuit and/or power cables. Wire those cables at
least 100mm(3.94 inch) away from the main circuit and/or power cables. It
may cause malfunction due to noise interference.
DANGER
CAUTION

A-2
[INSTALLATION PRECAUTIONS]
CAUTION
zUse the module in an environment that meets the general specifications
contained in this manual. Using this module in an environment outside the
range of the general specifications could result in electric shock, fire,
erroneous operation, and damage to or deterioration of the product.
zDo not directly touch the module's conductive parts.
Doing so could cause malfunction or trouble in the module.
zSecurely fix the module in place using the DIN rail. If the module is not
securely fixed, it may fall off or cause malfunction.
[WIRING PRECAUTIONS] DANGER
zPerform installation and wiring after disconnecting the power supply at all
phases externally. If the power is not disconnected at all phases an electric
shock or product damage may result.
CAUTION
zWire the module correctly upon verifying the product's rated voltage and the
connector pin arrangement. Connecting to a power supply different from
rating or miss-wiring may cause fire and/or product failure.
zMake sure foreign objects do not get inside the module, such as dirt and wire
chips. It may cause fire, product failure or malfunction.
[STARTING AND MAINTENANCE PRECAUTIONS]
DANGER
zDo not touch the connector pins when the power is on. It may cause an
electric shock or malfunction.
zBefore cleaning the module, be sure to shut off all the phases of the power
supply externally.
Failure to do so may cause failure or malfunction of the modules.
CAUTION
zDo not disassemble or modify the module. Doing so may cause failure,
malfunction, injury, or fire.
zThe module case is made of resin; do not drop it or subject it to strong shock.
A module damage may result.
zMake sure to switch all phases of the external power supply off before
installing or removing the module to/from the panel. Failure to do so may
cause failure or malfunction of the modules.
zBefore touching the module, always touch grounded metal, etc. to discharge
static electricity from the human body, etc.
Not doing so can cause the module to fail or malfunction.
[DISPOSAL PRECAUTIONS] CAUTION
zWhen disposing of this product, treat it as industrial waste.

A-3
Revisions * The manual number is noted at the lower left of the back cover.
Print Date *Manual Number Revision
Aug., 2003 IB(NA)-0800260-A First printing
This manual confers no industrial property rights or any rights of any other kind, nor does it
confer any patent licenses. Mitsubishi electric Corporation cannot be held responsible for
any problems involving industrial property rights which may occur as a result of using the
contents noted in this manual.
2003 MITSUBISHI ELECTRIC CORPORATION

A-4
CONTENTS
1. Overview........................................................................................................1
2. Specifications.................................................................................................1
2.1 General Specifications..............................................................................1
2.2 Performance specifications.......................................................................2
3. Part Names....................................................................................................3
4. Handling Precautions.....................................................................................5
5. Wiring.............................................................................................................6
5.1 External wiring..........................................................................................6
5.2 Connection and wiring of the connector for I/O interface...........................7
6. External Dimensions......................................................................................8

1
1. Overview
This user's manual explains specifications and names of individual parts of the
CL2XY16-DTP1C5V type CC-Link/LT remote I/O module (hereinafter
abbreviated as remote I/O module).
2. Specifications
2.1 General Specifications
The General specifications for the remote I/O module are shown in the following
table. Item Specifications
Operating ambient
temperature 0 to 55
Storage ambient
temperature -25 to 75
Operating ambient
humidity 5 to 95%RH, non-condensing
Storage ambient
humidity 5 to 95%RH, non-condensing
Frequency Acceleration Amplitude Sweep
count
10 to 57Hz ——— 0.075mm
(0.003in.)
Under
intermittent
vibration 57 to 150Hz 9.8m/s2———
10 to 57Hz ——— 0.035mm
(0.001in.)
Vibration
resistance
Conforming
to JIS
B 3502, IEC
61131-2 Under
continuous
vibration 57 to 150Hz 4.9m/s2———
10 times
each in
X, Y, Z
directions
(for 80
min.)
Shock resistance Conforming to JIS B 3502,
IEC 61131-2 (147 m/s2, 3 times in each of 3 directions X, Y, Z)
Operating
ambience No corrosive gases
Operating altitude 2000m (6562ft.) max.
Installation location Inside control panel *3
Overvoltage
category *1 II max.
Pollution level *2 2 max.
*1: This indicates the section of the power supply to which the equipment is assumed to be
connected between the public electrical power distribution network and the machinery
within premises. Category II applies to equipment for which electrical power is supplied
from fixed facilities.
The surge voltage withstand level for up to the rated voltage of 300 V is 2500 V.
*2: This index indicates the degree to which conductive material is generated in terms of the
environment in which the equipment is used.
Pollution level 2 is when only non-conductive pollution occurs. A temporary conductivity
caused by condensing must be expected occasionally.
*3: It can also be used in an environment other than on the control panel if the conditions such
as usage ambient temperature and humidity are satisfied.

2
2.2 Performance specifications
The performance specifications for the remote I/O module are shown in the
following table. Type
Item CL2XY16-DTP1C5V
Input specifications Output specifications
Number of inputs 8 points Number of outputs 8 points
Isolation method Photocoupler isolation Isolation method Photocoupler isolation
Rated load voltage 24V DC (Common with the
module power supply) Rated load voltage
24V DC (Common with
the module power
supply)
Rated input current Approx. 4mA Max. load current 0.1A/point 0.8A/1
common
Max. simultaneous ON
input points 100% Max. inrush current 0.7A 10ms or lower
ON voltage/ON current 19V or more/3mA or more Leakage current
at OFF 0.1mA or lower
OFF voltage/OFF current 11V or lower/1.7mA or lower Voltage drop at
ON
0.3V or lower (TYP.)
0.1A, 0.6V or lower
(MAX.) 0.1A
Input resistance 5.6k Output method Sink type
Protect function - Protect function Overload protection
function ,Overheat
protection function
Response
time setting
0.5ms
(High speed
response type)
1.5ms
(Standard
type)
TYP. 0.05ms -OFF
ON MAX. 0.1ms 1.5ms
OFF
ON 0.5ms or lower
TYP. 0.2ms -
Response
time
ON
OFF MAX. 0.5ms 1.5ms
1.5ms
(Standard
type) ON
OFF 0.5ms or lower (Resistive load)
Input method Positive common Surge
suppression Zener diode
Common wiring method 8 points/1 common (sensor
connector 3-wire type) Common wiring method
8 points/1 common
(sensor connector
2-wire type)
Number of stations
occupied In 4-point mode: Occupies 2 stations In 8 or 16-point mode: Occupies 1 station
Voltage 24V DC (-15 to +20%) (ripple ratio : within 5%)
Current
consumption 50mA or lower (When 24V DC and all point is on)
Module
power
supply Current on
startup 70mA or lower (24V DC)
Noise durability DC type noise voltage 500Vp-p, noise width 1µs,
noise carrier frequency 25 to 60Hz (noise simulator condition)
First transient/noise burst IEC 61000-4-4 : 1kV
Withstand voltage 500V AC for 1 minute between primary (external DC terminal) and
secondary (internal circuit)
Insulation resistance 10M or more between primary (external DC terminal) and secondary
(internal circuit) when measured with a 500V DC insulation resistance tester
Protection class IP2X
Weight 0.08kg
I/O part connection
method
Open sensor connector (e-CON) 16
(Connector plugs are sold separately (compatible wire size: 0.08 to 0.5
mm2, depending on the connector plug used). Refer to the CC-Link/LT
Catalog.)
Module installation
method DIN rail installation, Can be installed in six directions

3
3. Part Names
This section explains the names of the components for the remote I/O module.
5)
6)
7)
1)
No.
IN OUT
CL2XY16-DTP1C5V
PW
L RUN
L ERR.
LINK/PW
ON
87654321
ST.
9
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
X
0
1
2
3
4
5
6
7
Y
0
1
2
3
4
5
6
7
12345678 ON
ST.
No.
9
4) 2)3)
Connector for I/O interface Pin No. Signal
name Pin No. Signal name Pin No. Signal name Pin No. Signal name
1 +24V 1 +24V 1 +24V 1 +24V
2 +V 2 +V 2 NC 2 NC
3 24G 3 24G 3 NC 3 NC
CON1
4 X0
CON5
4 X4
CON
9 4 Y0
CON
13 4 Y4
1 +24V 1 +24V 1 +24V 1 +24V
2 +V 2 +V 2 NC 2 NC
3 24G 3 24G 3 NC 3 NC
CON2
4 X1
CON6
4 X5
CON
10 4 Y1
CON
14 4 Y5
1 +24V 1 +24V 1 +24V 1 +24V
2 +V 2 +V 2 NC 2 NC
3 24G 3 24G 3 NC 3 NC
CON3
4 X2
CON7
4 X6
CON
11 4 Y2
CON
15 4 Y6
1 +24V 1 +24V 1 +24V 1 +24V
2 +V 2 +V 2 NC 2 NC
3 24G 3 24G 3 NC 3 NC
4 3 2 1 4 3 2 1
CON1
CON2
CON3
CON4
CON5
CON6
CON7
CON8
CON9
CON10
CON11
CON12
CON13
CON14
CON15
CON16 CON4
4 X3
CON8
4 X7
CON
12 4 Y3
CON
16 4 Y7
Connector for CC-Link/LT interface Pin No. Signal name
1 +24V
2 DA
3 DB
1234
LINK/PW
4 24G

4
No. Item Description
LED name Confirmation details
PW On: Power supply on. Off: The power supply is turned off or the voltage drop is too
large.
L RUN On: Normal communication.
Off : Communication cutoff
(time expiration error).
L ERR.
On: Indicates that a communication data error has occurred or
the setting switch is outside the allowable range.
Flicker at regular intervals:
Indicates that the setting switch has been changed while
current is being conducted.
(The module continues to operate even while the LED is
flickering. The changed settings will be reflected when the
power has been restored.)
Flicker at irregular intervals:
Indicates that the terminal resistor is left unconnected or
that the module or connection cable are affected by noise.
Off: Normal communication.
0 to 7 Displays the ON/OFF status of the input (turned on in the ON
status and turned off in the OFF status).
1) Operating
status indicator
LEDs
0 to 7 Displays the ON/OFF status of the output (turned on in the ON
status and turned off in the OFF status).
2) Output hold
setting switch *
(SW9)
Specifies whether to maintain or turn off the output of the remote I/O module
in case the communication stops.
The switch is set to OFF at shipment from the factory.
ON: Maintain output
OFF: Turn output off
3) Response time
setting switch *
(SW8)
Set the response time (OFF ON/ON OFF time) of the remote I/O module.
OFF is set as default (factory-set).
Noise may be taken in as input, if high speed response type is set.
Be sure to set response time in consideration of the environment.
ON: 0.5ms (High speed response type)
OFF: 1.5ms (Standard type)
Select "10", "20" or "40" to set the ten's place of the station number.
Select "1","2","4" or "8" to set the one's place of the station number.
All switches are set to OFF at shipment from the factory.
Always set the station number within the range of 1 to 64.
A setting error occurs and "L ERR." LED flickers if the value outside the range
1 to 64 is set.
(Example) Set the switches as below when setting the station number to 32:
Ten's place One's place
Station
number 40
(SW1) 20 (SW2) 10 (SW3) 8 (SW4) 4 (SW5) 2 (SW6) 1 (SW7)
32 OFF ON ON OFF OFF ON OFF
4) Station number
setting switches
*
(SW1 to 7)
5) Connector for
CC-Link/LT
interface
Connector for connecting the CC-Link/LT communication line, module power
supply and load power supply.
6) Connector for
I/O interface Sensor connector for connecting output signals.
7) Hook for
DIN rail Hook for installing the module on a DIN rail.
* Set up using a slotted screwdriver with a tip width of 0.9 mm or less.

5
4. Handling Precautions
(1) When using a DIN rail, attach the DIN rail after taking the following items
into consideration:
(a) Applicable DIN rail types (conform to JIS C 2812)
TH35-7.5Fe
TH35-7.5Al
(b) Interval between the DIN rail's installation screws
Tighten the screws using a pitch of 200mm (7.87in.) or less when
attaching a DIN rail.
(2) To attach the remote I/O module to the DIN rail, press the centerline area of
the DIN rail hook beneath the module until a click is heard.
(3) When installing the remote I/O module into a panel, etc., provide 15mm
(0.59 in.) or more of space between the top and bottom of the module and
other structures or parts so that good ventilation and ease of operation
when exchanging modules can be secured.