Mixwell MW1081 User manual

User Manual

Size: 180*180*280mm
Weight: XXkg
Main materials: ABS
Power: AC100~240V 50/60Hz
Power consumption: 10W
Speed: 1/2/3
CADR:
Airflow:
Noise Level: 35~55 dBA
Specification
Product overview
Top cover
Filter
Buttom
DC Power
Control panel

Air outlet
Air inlet
NOTE：Please take notice of below instructions and the
separately included warning sheet before using the product.
Installation
·Please do not set up in a place where humidity directly hits curtains,
furniture, indoor plants or doors. It can cause stains and deformation.
·Please place on a horizontal and stable surface, otherwise the might be a
risk of water spilling.
·Please do not set up in a place where only childern are present such as
children’s room. It can lead to injury or breakdown if the device is knocked
over or climbed on.
·Please do not place anywhere where items may fall from above. It can
lead to ignition or a breakdown.
·Please do not set up near devices that are not compatible with water such
as PCs or smartphones. It can cause ignition or a breakdown.
·Please do not use in any surrounding that could lead to the water in the
water tray or in the device to freeze. Howere, if the water in the water tray
or the device is frozen please do not operate the device until the ice has
thawed. It can cause ignition or a breakdown.
Adapter

Placement
Please place away from walls, window and furniture.
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/ TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, Human proximity to the antenna shall
not be less than 20cm (8 inches) during normal operation
Advantages
·High CADR with True HEPA.
·Purifiy the air through 360°
and filter pm2.5 particles.
360°360°

·Even when it is placed at a sufficient distance from walls or furniture, if it is
used in the same place for a long period of time, it can become dirty with
scale. We recommend regular cleaning. Please consult chapter 4 for
maintenance instructions.
·Please avoid places with direct sunlight. There is a risk that the device
discolors.
·If there is interference with TV, radio or other electrical devices, please
move the device.
·When, moving the device please move it with the base of the device held
securely.
·The device dose not have an automatic humidity adjustment feasture. Wet
floors and condensation can form easily in rooms with lower temperatures
or high levels of humidity.
·Adjust the level of humidity with the mist button, with adequate
consideration of the space the device is located in, and by either raising the
room temperature or turning off the device.
Back:at least 30cm
Side:at least 30cm
Side:at least 30cm
Front:at least 30cm
Top:at least 100cm
Plug the power cable into the power
socket of the main unit, and insert
the DC plug firmly into the outlet.
The unit turns to the standby mode,
the indicator light on the top turns red.
Operation Guides
Plug in

Press the button for 1st time to turn on the unit
with 1 beep.The indicator is in white.Press 2nd
time to turn off the unit.Then recycle.
Hold the button for 5s when working,the unit will
connect WIFI after 1 beep,then the power indicator
will flash with red.
Remark:In the state of turning-off,the indicator will
be off after 3 mins.
When turning on the unit, the default setting is all
color cycle one by one. When touching the night
light button, you can select the light color currently.
When touching the button for the 2nd time, the
light color will cycle again. Hold on the button for
3 seconds, the night light will be turned off. And
then touch the button again, you can turn on the
night light. In the state of stand-by,the night light
can use individually.
Indicator
Power button/WIFI button
Night light setting
(Light color:red,blue,green,yellow,purple)
Speed button
Turning on the unit,the default setting is in low speed with light LED .Press
1st time,it’s 2nd speed with lighter LED;Press 2nd time,it’s 3rd speed with
lightest LED; Press 3rd time,it’s returning to 1st speed with light LED.
Remark:There’s memory function.Turn on the unit again to back to the last
speed after turning off. If plug out the unit,then it’s back to the default setting
when turn on again.

Sleep mode/Filter reset button
Press the button,enter into sleep mode,all LED are off with 1 beep. Press
any key to recover the sleep mode with 1st speed automatically.Press
again to turn off the sleep mode.
When the lifespan of filter used for 4320 hours,the indicator and all LED
will flash 10sec with beep.Then all LED and beep turn off.Every 30 mins,
the indicator and all LED will flash 3sec.
Hold the filter for 5s to reset the filter with two beeps and power indicator
flash 3s in red,then it shows resetting is successful.
Replacing the Filter
Open the top cover, take out the old filter, then put a new filter inside.
Please remove the plactis bag for the filter before useing.
After install the top cover, press the “ + ” button for 5s to reset the filter timer.
Rmark: It’s recommended to replace the filter every 6 months.
It depends on where and how the product is used. For example, if it’s used in
heavily contaminated areas, ect., the repalcement cycle of the filter may be
shorted.
Also, you can replace the filter immediately if the filter is dirty, judging by its
transparent cover.