MJX R/C Bugs 6 User manual

Brushless motor
(1906 275001
4-in-I ESC  Two-direction 2.4GHZ
(sleek and high-  (weak signal and low voltage
temperature protection).  remote onnireler alarm)
* or
19:
(070
k
LJ
Brushless Drone
Instruction Manual

Important statement and safety guidelines
Thank you for purchasing MJX product. Please read this manual carefully before use and retain it for
future reference.
Important statement
• This aircraft is not a toy, but hobby grade model. It should be assembled and operated properly. Pilot
must operate this hobby model in safe way. Improper operation may cause injury or property damage.
• This aircraft is applicable for pilots aged 14+ who are with skilled flying experience.
• Users are in full charge of proper operating this aircraft. Manufacturer and dealers disclaim any
responsibity for damages caused by misuse.
• Keep the small accessories away from kids to avoid accident.
Flight safety guidelines
Hobby grade radio control aircraft is somewhat considered to be the highest danger potential article.
Users should firmly uphold the principle of "safety comes first". Never fly the aircraft near airports,
above crowds or in zones storing dangerous goods and understand the responsibility of the accident
may cause by improper operations.
• Stay away from obstacles, crowds, power lines. trees or waters
Always choose a wide open area for every flight, well away from people and property. Never fly directly
over people or animals. Please c:on't sly in such bad weather conditions as high temperature, snow,
strong wind (?level 5), rain or fog. Maintain a 7ft (2m) distance from the aircraft when taking off and
landing.
• Keep the aircraft in dry environment
The aircraft is composed by sophisticated electronic components and mechanical parts. To avoid
damages on the mechanical and electronic components, please keep the aircraft in dry environment
and use clean cloth to wipe the surface and keep it clean.
• Practice flying together with skillful pilot
Beginners are suggested to practice flying together with skillful pilot's guidance. Do not fly alone.

• Bear proper operation and safe flight guidelines in mind
Please take a careful look at the manuals before flights for important information of product functions
and operation tips, and learn how to use the accessory, safe flight always comes first. Stay informed
of and abide strictly by relevant local laws and regulations. Keep away from any non-flight zones and
respect other people's privacy.
• Safe flying
Please make sure you are in good shape mentally before every flight. Fly the aircraft as per your flying
experience. Never fly under influence of alcohol or drugs. Keep the remote controller at least 20 cm
away from your body when flying the aircraft
• Keep distance from a flying aircraft
Never use your hands to touch a flying aircraft under any circumstance. Don't approach and touch a
landed aircraft before its propellers are completely locked.
• Keep away from heat source
The aircraft is made of metal, fiber, plastic, electronic component and other material. Please keep it
away from the heat source to avoid deformation or even damage caused by sun exposure and high
temperature.
• Environmental protection requirements
To protect our blue planet, so please recycle the aircraft as per local laws and regulations.
Product profile
Product configuration
Package includes
Aircraft (camera not included) X1  Extra Propellers A/B X2 
Protection guard X4
Propeller changing tool X1 
Charging converter X1  USB cable X1
Remote controller X1  Battery X1  Screw driver X1
Technical parameter of the aircraft
Diagonal. 175mm

Overall height: 65mm  Brushless motor: 1306 2750KV
Gross Weight: about 190g

Battery: 7.4V 850mAh 45C  Charging time: about 3 —3.5 hours
Maximum flying time: about 10 minutes
-2-

Product assemble
Propellers installation/removal
•
Installation
Install propeller A and propeller B on the corresponding motor shaft and fix the rotor propellers tightly by
rotating them as per the "lock" direction showed on the propellers.
•
Removal
Fix the brushless motor by rotor blade changing tool and then rotate and remove the propellers as per
the "unlock" direction showed on the propellers.
A
• Please make sure that the clockwise and the counter clockwise propellers are installed on the
correct motors, because the aircraft will not fly normally for wrong propellers installation.
• Be careful when installing the propellers, as they are a little sharp.
• Please use MJX propellers for this aircraft.
• Extra propellers can be ordered additionally.
Protection guard installation
Place the drone on flat surface and locate the two insertion position on the outer edge of the propeller
arm; install the protection guard on each propeller arm by aligning the protection guard as shown; make
sure that the protection guard is installed in the right position.
-3-

t-)
LI
Battery installation and remove
Install the battery: Uncork the soft insulation plug from the power interface at the rear of the aircraft
before the first use (indicated as pic. 1). Insert the battery into the battery compartment (indicated as
pic2). The aircraft will make beep sound with LED lights flashing; make sure that the battery is installed
firmly and the lock is at the right position; failure to do this may result in safety problem during the flight.
Take out the battery: Press down the lock and take the battery out (indicated as pic. 3).
Pic_ 1

Pic. 2

Pic. 3
4 L Attention: The battery should be installed firmly, failure to do so may affect the flight safety of
your aircraft. The aircraft may crash due to power-cut during the flight.
How to install the battery of remote controller
Open the battery door, install A' AA batteries into the battery compartment according to
the given polarity and then i:;lose the battery compartment.
A
.Insert batteries with correct polarity.
. Non rechargeable batteries are not to be charged; the transmitter need CAA batteries for work.
. Do not mix old and new batteries.
. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
. Rechargeable batteries are to be removed from the toy before being charged;
. Rechargeable batteries are only to be charged under adult supervision;
. Exhausted batteries are to be removed from the toy;
. The supply terminals are not to be short-circuited.
How to charge the battery of aircraft

Stew!: Slide the charging converter  the battery and insert the pins into the battery charging plug;
Step2: Insert the white socket o the 1 ._ISE cable into the white plug of the converter;
Step3: Then, insert the plug tl - e USB cable into the USB socket of power adaptor to start charging.

The indicator light of the LISB  will be in red color and keeps solid on when charging is
proceeding; when charging is finished, the indica or light will be off. Full charging takes about
3 to 3.5 hours.
Battery

Charging converter  USB cable  Power adaptor (not included)
 [0
-4-

A
Warm tips: We recommend using 5V 1A adaptor for charging.
It is not suggested to charge by computer
•
Need adult supervision when this model is being played by children.
•
Only batteries of the same or equivalent type as recommended are to be used
•
Insert batteries with correct polarity.
•
Nan rechargeable batteries are not to be charged; the transmitter need VAA batteries for
work.
•
Do not mix old and new batteries.
•
Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
•
Rechargeable batteries are to be removed from the toy before being charged.
•
Rechargeable batteries are only to be charged under adult supervision.
•
Exhausted batteries are to be removed from the toy.
•
The supply terminals are not to be short-circuited.
•
The charging line to be used with the product should be regularly examined for potential
hazard, such as damage to the cable or cord, plug, enclosure of other parts and that in the
event of such damage, the product must not be used until that damage had been properly
removed.
LED light installation
❑ pen the upper cover and install the LED light in place (shown as plc. 1) and screw tightly by clockwise
(shown as pic.2)
pie. 1

pic. 2
Major parts of the model
[1]
[2]
[3]
[1]
LED light
[2] Brushless motor
[3] Undercarriage
[4] Propeller
[5] Protection guard
-5-

 Bi I
• 7 1 111pr ,
[7]
[6] Battery compartment
[7]
Front light
[8] Rear light
[6]
[9]
Major parts of the remote controller
[1] Unlock (short-press)!
[7]

lock (long-press)
[2] Light switch
[3] Lei stick
[4] Turn left right trimmer
[5] Angl.
: moce:Acro mode
[10]
r f) POW& SWitCh
POV,:a
- indicator
[11]
8. High/Lov,: speed switch
[12]
.
9
. Photolshooting
. U] Right stick
[11] Leftward/rightward flight trimmer
[12] Forward/backward trimmer
[13] [14]
[13] 3D flips & rolls button
[14] Null button
-6-

j
inni
Remote controller
How to connect the signal of the aircraft with the
remote controller
• Keep pressing the red button and turn on the remote controller. The remote controller makes 2 beep
sounds, and the indicator lights keeps flashing; the remote controller is under signal connection
status.
• Turn on the aircraft. Once signal connection is done, the remote controller will send out a long beep
sound and the indicator light keeps solid on
■ Signal connection is done once for all if the remote controller is not linked to other aircraft.
• Set the connection one by one to avoid signal connection error.
Remote controller control stick calibration
1. Keep pressing the red locking button and turn on the remote controller.
2. Push down the calibration button (shown as pic.1) and hold on for 3 seconds, the remote controller
will make 3 beep sounds and the indicator light of the remote controller turns from flashing quickly to
slowly. Maximum rotate both of the left and right control stick to any direction for 2 circles (shown as
3. Then, again, push down the calibration button and hold on for 3 seconds. The remote controller will
send out 3 beep sounds and the indicator light of the remote controller turns from flashing slowly to
quickly, which means that the control stick calibration is completed.
A
Warm tips: All remote controllers have been calibrated when manufacturing.
Remote controller calibration is requested only if pilots find that the remote controller
control sticks are not working normally.
Attention: Please do not power on your aircraft when calibrate the control stick for the remote
controller.
A
-7-

Aircraft gyro calibration
After the aircraft and the remote controller are banded, set the aircraft on flat ground and follow the
indication photo as below to calibrate the gyro. Once the aircraft front lights turn from flashing to solid
on, the gyro calibration is succeeded.
• This is not compulsory step. But it is recommended to do gyro calibration for every flight to obtain
best flight experience.
How to lock and unlock the aircraft
Unlock the aircraft
Once the aircraft and the remote controller are banded, the front lights of the aircraft keep solid on
Short-press the red button (indicated as below photo), the aircraft and the remote controller make a long
beep sound; and the rear lights of the aircraft keep solid on; the motors rotate slowly, the aircraft is
unlocked.
Lock the aircraft
Method 1: Pull down the throttle stick to the bottom position, long-press the red button (indicated as
below photo). The remote controller sends out interrupted beep sound. Then, the motors stop
rotating and the rear light is off, which means that the aircraft is locked.
Method 2: After the aircraft lands on the ground, pull down the throttle stick to the bottom position for
15 seconds; then, the motors stop rotating and the aircraft lock automatically. Once the
aircraft is locked, it could not fly unless the motor is unlocked.
A
Warnings: The throttle control stick should be skied to the bottom position when long-press
the red button to lock the aircraft. Otherwise, the aircraft could not be locked.
Angle Mode/Acro Mode
Angle mode:
Angle mode. also named as self-level mode, is an assisted flight mode where the flight controller would
alv,:ays attempt to put the aircraft in its neutral position when there is no user control. This means that
with yoi.r hands off the controls, it will use 6-axis gyroscope to keep the aircraft level. The aircraft can
pel'orrn flips and rolls by pressing the rolls button and operating joystick. It is suitable for beginner.
-8-

Turn Left Turn Right
Left Side Flight
Front
Rear
Right Side Flight
Acro mode:
Acro mode, as known as rate mode, doesn't level the aircraft automatically but always requires manual
control during flight. Acro mode uses only the 3-axis gyro sensor. This is the more difficult mode for
flying but also much more responsive. Acro mode is great for acrobatics such as flips and rolls. The
aircraft can preform flips and rolls by operating joystick. It requires that pilot should be skillful enough
and beginner is not suitable for Acro mode.
• Please choose flight mode before turn on the remote controller.
How to choose the flight mode:
Step 1. Slide the flight mode button to the top position of q)" or the bottom position of "®'' before power
on the aircraft and the remote controller. It is null at " X '' position.
Step 2. Open the remote controller and install the battery of the aircraft.
Pic. 1

Pic. 2

Pic. 3
A
Warm tips:
• Under Acro mode, the aircraft and the remote controller will make "beep beep beep' sound
when it is in signal connection status.
• Acro mode is the more difficult flying mode, which is also much more responsive. It requires
skillful pilots.
Operate the aircraft
Remote controller

Aircraft Remote controller Aircraft
-9-