MK Diamond Products MK-212 Series System manual

MK-212 SERIES
OWNERS MANUAL &
OPERATING INSTRUCTIONS
www.mkdiamond.com
MK Diamond Products, Inc.
Caution: Read all safety and operating instructions before
using this equipment.This owners manual MUST accompany
the equipment at all times.
04.2009Revision 200
Manual Part No. 159862

40
MK-212-6 SAW PART LISTS
Part# 165652

41
MK-212-6 SAW PART LISTS
ITEM
NO. DESCRIPTION
PART OR
IDENTIFYING
NO.
QTY.
REQ.
1NUT, 3/8 - 16 HEX 101188 4
2NUT, HEX, 5/16 - 18 101196 2
3FITTING, PLASTIC, 1/4 FNPT X 1/4 BARB 128397 1
4HOSE,VINYL, 3/8 X 1/4 132951 1
5SCREW, 5/16 - 18 X 1-3/4 HEX HEAD CAP 150919 4
6WASHER, 3/8 SAE FLAT 150923 15
7WASHER, 3/8 SPLIT LOCK 150925 12
8SCREW, PAN HD SELF TP10-24 X 3/8 151262 1
9BOLT, HEX HEAD 1/4 - 20 X 3/4" 151267 4
10 PUMP,WATER 115V/60HZ UL/CSA 151271 1
11 SCREW, 5/16 -18 X 3/4 HEX HEAD MACHINE 151369 2
12 KNOB, 5/16 -18 X 1 151681 1
13 SCREW, 5/16 -18 X 1 HEX HEAD MACHINE 151743 4
14 WINGNUT, 5/16 -18 NYLOK 151746 1
15 WASHER, LOCK, SPLIT, 5/16 151747 10
16 WASHER, 5/16 SAE FLAT 151754 8
17 SCREW, WING, 1/4 - 20 X 1/2 151888 1
18 WASHER, 1/4 SAE FLAT 151915 14 T
19 WASHER, 1/4 SPLIT LOCK 152591 4
20 SCREW, 1/4 - 20 X 1/2 HEX HEAD 152608 8
21 STUD, 5/16 - 18 X 1-1/2"  1
22 SCREW, PHILP SELF TAP 10 - 24 X 5/8" 153681 1
23 F.H.C.S. 3/8 - 16 X 1" 154019 4
24 LABEL, 1-3/4 X 5 MK LOGO 154335 2
25 CLAMP, HOSE 1/2 - 3/4 154394 1
26 SCREW, 1/4 - 20 X 3/4 FLAT HEAD PHILLIPS MACHINE 154657 4
27 LEG 155397 4
28 SCREW, THUMB 3/8 - 16 X 3/4" 155398 4
29 BLADE, 10" TILE 155619 1
30 LABEL, SAFETY 155806 1
31 SCREW, SHLDR, SOC HD, 1/2 X 3/4 156177 2
32 SCREW, SOCKET HEAD CAP 3/8 - 16 X 1 156602 12
33 KNOB,TRI 156770-02 2
34 TAG, SERIAL #, BLANK 157500-RW 1
35 DRIVE SCREW, #7 X 5/16 ROUND HEAD 157849 2

42
MK-212-6 SAW PART LISTS
Part# 165652

43
MK-212-6 SAW PART LISTS
ITEM
NO. DESCRIPTION
PART OR
IDENTIFYING
NO.
QTY.
REQ.
36 GUARD, BLADE 159416 1
37 POST, PIVOT (COMP) 159418 2
38 TABLE ASSEMBLY 159420 3
39 GUARD, INNER BLADE (COMP) 159423 1
40 KNOB, 1/4 - 20 X 1 - 1/4 159428-2 1
41 PROTACTOR ASSEMBLY 159572 1
42 BLOCK, RAIL 159622 2
43 MOUNT, SOGA MOTOR 159642 1
44 CUTTING HEAD 159853 1
45 MANIFOLD,WATER 159854 1
46 STOP, RUBBER BUMPER 159855 2
47 SCREW, SET UP 3/8 - 16 X 1/2" 159856 2
48 PLUG, 2-1/2 DIA RUBBER 159858 1
49 KEY, MOTOR MOUNT 159859 2
50 OWNER MANUAL 159862 1
51 NUT, 3/8 - 16 HEX 159863 1
52 FOOT, RUBBER 159977 4
53 WRENCH, 30MM OPEN END, 30DEG 159978 1
54 WRENCH, 5MM ALLEN 159979 1
55 STAND OFF, BACK STOP 160117 2
56 GUIDE, 15 INCH RIP (COMP) 160286 1
57 PLATE, PRESSURE 160287 1
58 GUARD, SPLASH 160310 1
59 SWITCH BOX 160687 1
60 MOTOR, 115V, 2HP SOGA 162078 1
61 RAIL, 2 X 2 X 50 165651 1
62 STOP, BACK 165685 1
63 LABEL, MK212-6 165928 2
64 MAT,TABLE 166418 4
65 TAPE,VHB 5952 3M 166487 1
66 PRIMER, 3M 23926 166488 1
67 PAN WELDMENT 166547 1
68 BRACKET, POST MOUNT 167376 1
69 BRACKET, HEAD MOUNT 167377 1
70 CARRIER, CABLE 167431 1
71 WRENCH, 5/16" ALLEN 167679 1

47
MK Diamond Products, Inc.
1315 Storm Parkway
Torrance, CA 90501
Toll-Free: [phone]
Phone: [phone]
Fax: [phone]
www.mkdiamond.com
MK-212 Series Saw
OWNERS MANUAL & OPERATING INSTRUCTIONS
DOCUMENT NO.159862