MK Diamond Products MK-377EXP User manual

02.2015
MK-377EXP TILE SAW
OWNER'S MANUAL
OPERATING INSTRUCTIONS
& PARTS LIST
www.mkdiamond.com
Caution: Read all safety and operating instructions
before using this equipment. This parts list MUST
accompany the equipment at all times.
Revision 201
Manual Part No. 160030
Part# 160028

30
MK-377EXP SAW EXPLODED VIEW
1
2
3
4
5
7
8
10
11
12
13
14
15
17
18
19
16
Saw Assembly A Part #160028

31
MK-377EXP SAW PARTS LIST
Item Description Part # Qty
1 HOSE, VINYL, 1/4X3/8 (6.0') 132951 1
2 CASTING, ACC RIP GUIDE-COMP 134551 1
3 WRENCH, TILE SAW NUT 15/16 134684 1
4 SCREW, WING, 1/4-20X1/2 151888 1
5 WASHER, FLAT, SAE, 1/4 151915 1
6CARTON, ACCESS PK-101/1080/880 153366 1
7 WRENCH, TILESAW, 11/16 OPEN END 153450 1
8 CLAMP, HOSE, 1/4-1/2 FLOW 154394 1
9 CASTING, BLD GRD, 7", COMP 154811 1
10 CARD, WARRANTY REGISTER SAW 155037 1
11 PUMP, WATER, 115V 60HZ 155987-VP 1
12 SELL SHT, TILE ACCESSORY 156915 1
13 CLIP, CORD 1/4" PUSH MOUNT 157259 1
14 MK-HDTCM WET 7X060X7/8 157913 1
15 KNOB, RUBBER, 1/4-20 X 3/4" LONG 159428-1 1
16 OWNER'S MANUAL MK-377EXP 160030 1
17 PAN, WATER MK-370EXP/1080 160041 1
18 GUARD, SPLASH 160310 1
19 SHEET, WARNING LABELS, TILE SAW 166012 1

32
MK-377EXP SAW EXPLODED VIEW
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
21
22
20
10
Saw Assembly B Part #160028

33
MK-377EXP SAW PARTS LIST
Item Description Part # Qty
1 FLANGE, OUTER, 2-3/8 135830 2
2 NUT, HEX, 5/8-18 135848 1
3 KNOB, DAVIES, 5/16-18 X 1 151681 1
4 SCREW, HEX HD, 5/16-18 X 1 151743 2
5 NUT, WING, NYLK, 5/16-18 151746 1
6 WASHER, LOCK, SPLIT, 5/16 151747 3
7 SCREW, HEX HD, TAP, 5/16-18X2-1/2 151748 1
8 WASHER, FLAT, SAE, 5/16 151754 4
9 SCREW, FLAT HD, 1/4-20X3/4 151657 5
10 CASTING, BLD GRD, 7", COMP 154811 1
11 FITTING, 1/8 MNPT X 1/4 BARB 155809 1
12 SCREW, FLAT HEAD, 1/4-20X1/2 PHIL 155812 7
13 MTR, 5.0 AMP 115V 50/60HZ 157226-G 1
14 CASTING 170, MOTOR MOUNT, COMP 157403 1
15 SCREW, FLAT HD, M5-8X16MM 157404 6
16 NUT, HEX, M5-.8 157405 6
17 TAG, SERIAL NUMBER, BLANK 157500-RW 1
18 SCREW, QUICK DRIVE, #8-32X1/4 162850 2
19 WELDMENT, FRAME 167449 1
20 ASSY, TABLE, 377EXP 170898 1
21 CASTING, POST, 377EXP, COMP 170899 1
22 ARM, CUTTING HEAD, 377EXP 170902 1

34
MK-377EXP SAW EXPLODED VIEW
1
2
3
6
7
8
2X 152227 BEARING, MULTILUBE
INCLUDED WITH TABLE
4
5
9 Part #170898

35
MK-377EXP SAW PARTS LIST
Item Description Part # Qty
1 SCREW, HEX HD, CAP, 5/16-18 X 3/4 151369 2
2 WASHER, LOCK, SPLIT, 5/16 151747 2
3 WASHER, FLAT, SAE, 5/16 151754 2
4 WASHER, FLAT, SAE, #8 155454 2
5 SCREW, 8-32 X 3/8 PAN HEAD PHILLIPS 156614 2
6CASTING, TABLE, 370/770EXP-COMP 159939 1
7 BAR, GUIDE 3/4 DIA 159942 1
8 ASSY, WHEEL BRKT, 370EXP 168023 1
9 INSERT, TABLE, 377EXP, COMP 170901 1

36
MK-377EXP SAW ACCESSORIES
ITEM
1. MK-200, 7" x 5/8 Arbor
2.
MK-215, 7" x 5/8 Arbor
3.
MK-315, 7" x 5/8 Arbor
4. Dual 45°Flat Angle Guide
5. 90° Protractor
6. Dressing Stone
7. Ground Fault Circuit Interrupter
8. Stand for 7" Tile Saw
139295 Premium grade Diamond Blade for
smooth, chip-free cutting on tile
139311 Supreme grade diamond blade
for hard materials
153293 Supreme super hi-rim diamond blade
134577-MK
134569-MK
152792
152610
160131
DESCRIPTION
5. Rip Guide134551-MK
NUMBER

37
NOTES

38
MK-377EXP SAW ORDERING & RETURN
ORDERING INFORMATION
You may order MK Diamond products through your local MK Diamond distributor or, you may order
direct from MK Diamond.
When ordering direct from MK Diamond, please have the following information ready before calling:
• The Model Number of the saw
• The Serial Number of the saw
• Where the saw was purchased and when
• The Part Number for the part(s) being ordered
• The Part Description for the part(s) being ordered
NOTE: There is a $25.00 minimum order when ordering direct from MK Diamond. A $6.00 charge will
be added to orders having a net billing value under $50.00. All purchases must be made using VISA,
MasterCard or American Express.
All parts may be ordered by calling toll free to – 800 421-5830 or 310 539-5221 and asking for
Customer Service. For technical questions, call – 800 474-5594.
RETURN MATERIALS POLICY
To expedite the service relative to the return of a product purchased through MK Diamond, please
observe the following:
NOTE: When returning all items, they must have been purchased within the previous twelve (12)
months.
• Have the Model Number of the saw
• Have the Serial Number of the saw
• Have the location of where the saw was purchased
• Have the date when the saw was purchased
• Contact Customer Service for approval to return the item(s)
• Obtain a Returned Goods Number (RGA) authorizing the return
• Follow the packaging instructions in the following section
• Ensure your item(s) are prepaid to the destination
For returned items, call toll free to – 800 421-5830 or 310 539-5221 and ask for Customer Service.
For technical questions, call – 800 474-5594 or 310 257-2845.
PACKAGING INSTRUCTIONS
• Remove the Cutting Head and Support Angle Assembly
• Dry the saw before shipping
• When packing, include the following: Saw, Diamond Blade, Blade Guard and Support Angle
Assembly and Adjustable Cutting Guide (Other Accessories are not required)
• Package the unit in its original container or one of comparable size (do not ship the unit partially
exposed)
• Ensure all parts are secured in the packaging to prevent moving
AUTHORIzED SERVICE CENTERS
For quicker repair time, you may contact MK Diamond Customer Service, toll free, at 800 421-5830
or 310 539-5221 for the Authorized Service Center closest too you or visit our web site at
www.mkdiamond.com. For technical questions, call – 800 474-5594.