MLS NG1028 User manual
1
MLS KICK-OFF TABLETOP SOCCER
TABLE ASSEMBLY INSTRUCTIONS
NG1028
2
Thank you for your purchase of our product.
We work around the clock and around the globe to ensure that our
products maintain the highest possible quality. However, in the rare
instance that your product is defective or missing parts, contact
Challenger Manufacturing at 800-759-0977 to submit parts requests
or warranty claims. Please read the warranty information at the back
of these assembly instructions for further details.
IMPORTANT! PLEASE READ THESE ASSEMBLY INSTRUCTIONS IN
ENTIRETY BEFORE ASSEMBLING YOUR PRODUCT.
THANK YOU!
PARTS IDENTIFIER (NOT TO SCALE)
ADDITIONAL EQUIPMENT REQUIRED:
3
ASSEMBLY TIPS
1. Find a clean, level surface to begin the assembly of your game table. The table will be
partially assembled upside down and then turned over onto its legs.
2. Remove all of the contents from box and verify that you have all of the parts shown on the
Parts Identier before you begin assembly. Note: Some parts may be pre-installed or
pre-assembled.
3. Some gures or drawings may not look exactly like your product. Please read and
understand the text before beginning each assembly step.
4. When installing parts that have more than one screw or bolt, hand tighten all screws or
bolts in place before nishing tightening with screwdriver or hex wrench.
5. Electric screwdrivers may be helpful during assembly; however, please set a low torque
and use extreme caution because screws may be stripped or overtightened if the electric
screwdriver's torque is set too high.
WARNINGS!
READ AND FOLLOW ALL ASSEMBLY, OPERATION AND SAFETY INSTRUCTIONS CAREFULLY.
CHOKE HAZARD - THIS TABLE CONTAINS SMALL BALLS AND PARTS - NOT
SUITABLE FOR CHILDREN UNDER 3 YEARS OF AGE.
4
ASSEMBLY INSTRUCTIONS
1. Attach one CORNER #17 to each side of one END PANEL #8 with 1/2" SCREW #4. Repeat
assembly with remaining CORNERS and END PANEL.
2. Insert pre-assembled GREEN PLAYER RODS #13 and BLUE PLAYER RODS #14 into one SIDE
PANEL #7 as shown below. Note: To avoid confusion, it may be helpful to lay out the PLAYER
RODS in their correct order and orientation BEFORE inserting them into the SIDE PANEL.
Although this table is assembled upside down, players are shown upright for clarity. Each
team should face the opposite goal when table is turned over - the visible screw head
indicates the front of the player. Ensure that the FOAM BUMPERS #18 and PLASTIC ROD
WASHERS #19 are in place before inserting rods into the SIDE PANELS.
3. Insert PLAYER RODS into remaining SIDE PANEL #7.
4. Slide PLAYFIELD #9 with eld markings facing down into the SIDE PANEL grooves.
5
ASSEMBLY INSTRUCTIONS (CONT.)
5. Attach one assembled END PANEL to each side of the table with 1/2" SCREW #4.
6. Attach each PLAYFIELD SUPPORT BRACE #16 underneath PLAYFIELD by fastening to SIDE
PANELS with 1-1/2" SCREW #3.
7. Attach one LEG #10 to each corner of the table using BOLT #1 and FLAT WASHER #2.
Carefully turn table over.
8. Attach HAND GRIP #12 to the marked end of each PLAYER ROD. Attach ROD END CAP #15
to the opposite end of PLAYER RODS.
9. Attach one TWO-PIECE GOAL #5 to each end of the table with 1/2" SCREW #4.
6
CONGRATULATIONS!
You have now assembled your MLS SoccerTable. Please
note the Care and Use instructions below to ensure
years of trouble free use of your game table.
CARE AND USE
1. This product is intended for INDOOR use only.
2. Do NOT sit, climb or lean on the table.
3. Do NOT drag the table when moving it as this will damage the legs.
7
90-DAY LIMITED WARRANTY
This product is warranted to the original purchaser to be free from defects
manship for a period of ninety days from the date of the original retail purchase.
This warranty does not cover defects or damage due to improper installation, alteration, accident or
any other event beyond the control of the manufacturer. Defects or damage resulting from misuse,
abuse or negligence will void this warranty. This warranty does not cover scratching or damage that
may result from normal usage.
This product is not intended for institutional or commercial use; does not
for such use. Institutional or commercial use will void this warranty.
This warranty is nontransferable and is expressly limited to the repair or replacement of the defec-
tive product. During the warranty period, shall repair or replace defective
the purchaser. Shipping charges and insurance are not covered and are the respon-
chaser. Labor charges and related expenses for removal, installation or replacement
components are not covered under this warranty.
reserves the right to make substitutions to warranty claims if parts or unav-
shall not be liable for loss of use of the product or other consequential
expenses or damages incurred by the consumer of any other use. The user assu-
resulting from the use of this product.
This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties of
nor any of its representatives assumes any other liability in connection with this product.
All warranty claims must be made through the retailer where the product was originally
purchased. A purchase receipt or other proof of date of purchase will be required to pro-
cess all warranty claims. The model number and part numbers found within the assem-
bly instructions will be required when submitting any parts requests or warranty claims.
For further warranty information or inquiries, please call 800-759-0977
Challenger Manufacturing
in material or work
Challenger Manufacturing
assume any liability
Challenger Manufacturing
parts at no cost to
sibility of the pur
of the product or
Challenger Manufacturing
Challenger Manufacturing
ailable or obsolete.
or incidental costs,
mes all risk of injury
Challenger
Manufacturing
Table of contents
