MobileVision MV2458 User manual

For Technical Assistance, please call [phone],
or visit www.magnadyne.com
Quickstart Guide
MV2458 Router

2
Press power button on the
MV2458 to power up the
Router and wait until all lights
are blue and flashing
(approximately 2 min).
Go to the WiFi setting on your
device (phone, tablet, laptop,
etc., make sure your WiFi is
turned on) and click on the
MV2458-2.4G Network.
MV2458 Software Quickstart Guide
Step 1 Step 2
MV2458-2.4G

3
In the Password field type in
the password MV2458WiFi
and click the Join button.
Password:
MV2458WiFi
Wait until your device is
connected to the
MV2458-2.4G Network.
Step 3 Step 4
*Case Sensitive
MV2458 Software Quickstart Guide
MV2458WiFi
MV2458-2.4G

4
Go to your web browser and in
the address field type in
192.168.10.1 and click Go or
hit Enter.
The Login screen will open. In
the Password field type in the
password admin and click
the Login button.
MV2458 Software Quickstart Guide
Step 5 Step 6
Address:
192.168.10.1
Password:
admin
*Case Sensitive
admin
192.168.10.1

5
Scanning countdown should
begin automatically.
The Available WiFi List screen
will appear. Click on the WiFi
Network that you would like
the Router to connect to.
If the scroll bar does not
appear and you are using a
Mac Computer, move the
cursor up and down over the
SSID names and the scroll bar
should appear.
Step 7a
If scanning does not begin
and the Status Screen shows
the MV2400 and MV2458 are
NOT PAIRED, go to Step 14.
Step 7b
Step 8
MV2458 Software Quickstart Guide
NOT PAIRED

6
The password pop-up window will appear. Type in the
password for the chosen WiFi host and click on the Connect
button.
Please acquire password from WiFi Host at your location.
If previously connected, the password will refresh
automatically from your connection history.
If the unit will not connect at this step, it may not have
finished it’s 2 minute boot cycle. Start again from Step 1
and wait 2 minutes for boot cycle to complete.
MV2458 Software Quickstart Guide
Step 9

7
In the Password field type in
the password admin and click
the Login button. If login is
successful, the unit will
proceed to Step 13.
Step 11
Password:
admin
*Case Sensitive
The Connecting countdown
page will complete and then the
Login screen will open.
You must wait 2 minutes
after hitting the connect button
for the unit to complete it’s
connection. 45 seconds will
result in a failed connection.
Step 10
45
MV2458 Software Quickstart Guide
admin

8
MV2458 Software Quickstart Guide
The Status Screen will appear
showing the connected Network
under the title MV2400 (Outside)
Information.
Congratulations, Setup Complete.
Step 13
If the password was not typed
correctly a pop-up window will
appear stating that the
connection to the Network failed.
Click the OK button. The unit will
return to Step 7 and scan again.
Double check you are typing the
correct Network password.
Step 12

9
Select Settings from the
drop-down menu.
In Settings select Pair MV2400.
Step 14 Step 15
Pair MV2400 to MV2458
The MV2458 and MV2400 have been paired at the factory, and are ready
to use together. If they become disconnected or switched with a new
unit, use Steps 14-19 to pair the MV2400 to the MV2458 for proper
operation.

10
Pair MV2400 to MV2458
Enter the Mac Address in the user’s
manual or the address listed on
your device.
The MAC address will have the
format of XX:XX:XX:XX:XX:XX
(Example 40:a5:ef:e1:e2:e9).
It is important to enter this number
exactly as displayed on the device or
in the user’s manual. The MAC
address entered MUST match the
device you are connecting to.
After entering the MAC
address click the Apply button.
Step 16 Step 17
40:a5:ef:e1:e2:e9 40:a5:ef:e1:e2:e9

11
Wait until the Pair MV2400
countdown has completed.
Return to Page 4, Step 6 to
connect to WiFi.
Step 18 Step 19
Pair MV2400 to MV2458

12
MV2458 Software Quickstart Guide
Copyright © 2017 Magnadyne Corp. MOBILEVISION-MV100-MV2458-QS Rev. A