Hirschmann OWL LTE User manual

UM Installation OWL_LTE
Release 1.0 09/2015 Technical Support https://hirschmann-support.belden.eu.com
User Manual
Installation
OWL LTE (Industrial Cellular Router)

Thenamingofcopyrightedtrademarksinthismanual,evenwhennotspeciallyindicated,should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2015 Hirschmann Automation and Control GmbH
Manualsandsoftwareare protectedby copyright.All rightsreserved.Thecopying,reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD/DVD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
ControlGmbHaccordingtothebestofthecompany'sknowledge.Hirschmannreservestheright
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(http://www.hirschmann.com).
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
Rel. 1.0 - Installation – 04.01.2016
Contents

Contents
UM Installation OWL_LTE
Release 1.0 09/2015
3
About this Guide 5
Legend 6
GPL License 7
Safety Instructions 8
1 Router Description 13
2 Contents of Package 15
3 Router Design 17
3.1 Router Versions 18
3.2 Delivery Identification 19
3.3 Basic Dimensions of Router Box 20
3.4 Mechanical Dimensions and Mounting Recommendations 21
3.5 Removing from the DIN rail 23
3.6 Description of the rear panel 24
3.7 Description of the Front Panel 25
3.7.1 Status Indication 26
3.7.2 Power Connector 27
3.7.3 Grounding the device (functional earth) 28
3.7.4 Antenna Connectors 28
3.7.5 SIM Card Reader 30
3.7.6 MicroSD card reader 31
3.7.7 Reset 32
3.7.8 Ethernet Ports ETH0 & ETH1 32
3.7.9 USB Port 34
3.7.10 I/O Port 35
3.7.11 RS232 interface 37
4FirstUse 39
4.1 Connecting Components before the First Use 40
4.2 Start 42
4.3 Configuration 43
4.3.1 Configuration using a Web Browser 43
5 Technical Parameters 45

Contents
4
UM Installation OWL_LTE
Release 1.0 09/2015
5.1 Basic parameters 46
5.2 Type tests and environmental conditions 47
5.3 Technical Parameters of module 48
5.4 Technical Parameters of the processor 49
5.5 Technical parameters of the GPS 50
5.6 Technical parameters of the I/O port 51
5.6.1 Characteristics of inputs 51
5.6.2 Binary output parameters 51
5.6.3 PoE PD Technical Parameters – PSE Requirements 52
5.7 Other technical parameters 53
6 Recommended literature 55
6.1 Available Literature 56
7 Possible problems 57
7.1 Solutions 58
8FAQ 59
9 Customers Support 61
9.1 CE-marking 62
9.2 E marking 63
A Further Support 65

About this Guide
UM Installation OWL_LTE
Release 1.0 09/2015 5
About this Guide
This document provides technical specifications for the Industrial Cellular
Router and illustrates the hardware installation for a Hirschmann Industrial
Cellular Router. It also helps the developers to validate their application
design using the Industrial Cellular Router.
The information in this publication contains general descriptions or
performance factors which, when applied in an actual situation, do not
always correspond with the described form and may be amended by way of
further development of products. The desired performance factors shall only
be deemed binding if these are expressly agreed on conclusion of the
contract. Please note that some characteristics of the recommended
accessory parts may differ from the appropriate product. This might limit the
possible operating conditions for the entire system.

About this Guide
6
Legend
UM Installation OWL_LTE
Release 1.0 09/2015
Legend
The designations used in this manual have the following meanings:
List
Work step
Subheading
Link Cross-reference with link
Note: A note emphasizes an important fact or draws your attention to a dependency.
Courier ASCII representation in the graphical user interface

About this Guide
UM Installation OWL_LTE
Release 1.0 09/2015
GPL License
7
GPL License
Source codes under the GPL license are available free of charge. Send an
email request to:
[email protected]

About this Guide
8
Safety Instructions
UM Installation OWL_LTE
Release 1.0 09/2015
Safety Instructions
General safety instructions
You operate this device with electricity. The safe operation of the device
dependsonproperhandlingduringtransportation,storageandassembly,
and proper use of operation and maintenance procedures. Improper use
of this device can cause injury or property damage.
Read this documentation, safety instructions and warnings before
connecting any cables.
Never start an operation with damaged components.
The device does not contain any service components. If the device is
not functioning correctly, or if it is damaged, turn off the power supply
and return the device to Hirschmann for inspection.
Qualification requirements for personnel
Allow only qualified personnel to work on the device who have the
following characteristics:
Properly trained personnel who have practical knowledge and
experience. This is the prerequisite for grounding and labeling
circuits, devices, and systems in accordance with current
technology safety standards.
Qualified personnel are aware of the dangers that exist in their
work.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all the data transmission devices.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

About this Guide
UM Installation OWL_LTE
Release 1.0 09/2015
Safety Instructions
9
Qualified personnel are familiar with appropriate measures against
thesehazards inorder to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.
Intended usage
Use the product only for the application cases described in the
Hirschmann product information, including this manual.
Operate the product according to the technical parameters. See “First
Use” on page 39.
Connect components which are suitable for the requirements of the
specific application to the product.
National and international safety regulations
Verify that the electrical installation meets applicable national and
international safety regulations.
Working voltage
Connect only a working voltage that corresponds to the type plate of
your device.
Make sure the following requirements are met every time you connect
the electrical conductors:
The power supply conforms to over voltage category I or II.
The power supply has an easily accessible disconnecting device
(such as a switch or a plug) which is clearly identified. So in case
of an emergency, it is clear which disconnecting device belongs to
which power supply cable.
The electrical wires are voltage-free.
The power supply is Class 2 compliant.
The working voltage inputs are designed for operation with safety
extra-low voltage. Connect only SELV circuits with voltage
restrictions in line with IEC/EN 60950-1 to the working voltage
connections.
The wire diameter of the power supply cable is at least 0.5 mm²
(North America: AWG20) on the working voltage input.

About this Guide
10
Safety Instructions
UM Installation OWL_LTE
Release 1.0 09/2015
The wire diameter of the ground conductor is at least 0.5 mm²
(North America: AWG20).
The power supply cables used are permitted for the temperature
range required by the application case.
The power cords are suitable for ambient air temperatures of at
least 167 °F (75 °C). The power cord wires are made of copper.
Turn on the operating voltage for the device only when the following
requirements are fulfilled:
The housing is closed
The terminal block is wired correctly
The terminal block for the operating supply is connected
Installation site requirements
Verify that there is at least 4 in (10 cm) of space above and below the
device.
Verify that there is at least 0.8 in (2 cm) of space on the right and left
sides of the device.
Verify that there is at least a minimum distance of 20cm between the
antenna and the human body.
Housing
Never insert pointed objects (narrow screwdrivers, wires, etc.) into the
device or into the connection terminals for electric conductors. Do not
touch the connection terminals.

About this Guide
UM Installation OWL_LTE
Release 1.0 09/2015
Safety Instructions
11
Please, observe the following instructions:
Topreventinjuryanddamage to thedeviceandtoensurethatyoucomply
with the relevant provisions, use original accessories only. Unauthorized
modifications or unapproved utilization of accessories can result in
damage to the router and in a breach of applicable regulations.
Unauthorized modifications or unapproved utilization of accessories can
result in the termination of the guarantee.
Before handling the SIM card, disconnect the router from the power
supply.
Do not exceed the maximum voltage of 30 V DC at the power
connector of the router.
Do not expose the router to extreme ambient conditions. Protect the
router against dust, moisture and high temperature. See table 12 on
page 46.
It is recommended that you should create an appropriate copy or
backup of the important settings that are stored in the memory of the
device.
Note: Insertthe SIM Card holder in the SIMcard slot verycarefully. When
inserted improperly, you can damage the SIM card slot. Also, the SIM
card can fall out of the holder and end up in the router.

About this Guide
12
Safety Instructions
UM Installation OWL_LTE
Release 1.0 09/2015

Router Description
UM Installation OWL_LTE
Release 1.0 09/2015 13
1 Router Description
Hirschmann has designed the OWL router for wireless communication in
mobile networks that make use of the following technologies:
LTE
HSPA+
UMTS
EDGE
GPRS
Due to the high speed of data transfer up to 100 Mbit/s (download) and up to
50 Mbit/s (upload) is this router an ideal solution for wireless connection of
data stream and security camera systems, individual computers, LAN
networks, automatic teller machines (ATM) and other self-service terminals.
As a standard, the router is supplied in a metal casing. The cellular router is
also equipped with the following interfaces located on the front panel:
2 Ethernet 10/100
1 USB 2.0 Host port
2 binary inputs
1 I/O output connector
1 microSD card reader
1 RS232 – serial interface
The following ports are located on the back panel of the router:
2 SIM card readers, 3 V and 1.8 V
1 microSD card reader
Configuring the cellular router is possible using a graphical user interface
which is password protected. The graphical user interface provides, after
logging in, detailed statistics about the activities of the router such as, signal
strength,andadetailedsystemlog.This device supports the creation of VPN
tunnels using technologies such as IPSec, OpenVPN and L2TP for secure
communications. The router also supports the following functions:
DHCP
NAT
DynDNS
IPSec
OpenVPN
NTP
VRRP

Router Description
14 UM Installation OWL_LTE
Release 1.0 09/2015
control by SMS
primary/backup connection
Diagnostic functions, which provide for continuous communication, include
an automatic inspection of a PPP connection, offering an automatic restart
feature in case of an unexpected termination of the connection. Another
diagnostic function is the hardware watchdog, which monitors the status of
the router.
Using a special window, the start up script window, you can insert Linux
scripts for various actions. For some applications, it is crucial to create
several different configurations for a router. You can exchange these
configurations as necessary for example, using SMS. The router can
automatically upgrade a configuration and firmware from a server. This
allows you to configure several routers at a time.

Contents of Package
UM Installation OWL_LTE
Release 1.0 09/2015 15
2 Contents of Package
The basic router set available for delivery includes the following items:
router
clip for the DIN rail
loose power connector
6 pin I/O connector
5-pin terminal block for RS232
quick installation guide
Figure 1: Contents of Package

Contents of Package
16 UM Installation OWL_LTE
Release 1.0 09/2015

Router Design
UM Installation OWL_LTE
Release 1.0 09/2015 17
3 Router Design

Router Design
18
3.1 Router Versions
UM Installation OWL_LTE
Release 1.0 09/2015
3.1 Router Versions
The OWL LTE is supplied with the following items:
2 Fast Ethernet 10/100BaseTX ports, RJ45
2 SIM Cards readers, for 3 V and 1.8 V SIM cards
2 SMA antenna connectors, Main + Rx Div
serial interface RS232 port with screw terminal
binary I/O ports (2x input, 1x output)
1 Mini SD card reader
1 GPS antenna connector
This router is available in a metal casing.
Figure 2: Front panel

Router Design
UM Installation OWL_LTE
Release 1.0 09/2015
3.2 Delivery Identification
19
3.2 Delivery Identification
Figure 3: Example of Router Label
Product Name Product Code Product Group
OWL LTE OWL LTE-S20TTA12121GTDAHH01.0 Industrial Cellular Router
Table 1: Delivery identification

Router Design
20
3.3 Basic Dimensions of Router Box
UM Installation OWL_LTE
Release 1.0 09/2015
3.3 Basic Dimensions of Router
Box
Figure 4: Basic Dimensions of Router Case