MOBILUS mobiWAN User manual

mobiWAN
USER GUIDE ENG

USER GUIDE mobiWAN ENG
Charging Port

USER GUIDE mobiWAN ENG
I. Insert the Rat het Clip between the Wheel Rat het and the suspension body. 
II. Atta h both “L” and “R” Transdu er Clips & to the suspension arms as shown.
III. The Coiled Wire should stay on the outside or inside of the suspension and below
the Transdu er Clips & .
IV. While wearing it on the head, adjust the position of ea h Transdu er Clip & by
sliding them up or down along the suspension for maximum omfort.
I. II.
INSTALL ON HARD HELMET

USER GUIDE mobiWAN ENG
SWITCH DEVICE ON/OFF
A short press for 1 sec on the Power Button will switch ON the mobiWAN. The LED
will light up White for a few seconds and the Mobilus’ tone will be heard. For the opposite
operation, to switch OFF the device, you need to long press the Power Button for a
few s econ ds. To co nfirm th is ac tio n th e LED will light up Red fo r a few seco n ds an d
the “Power Off voice prompt will be played.
While device is ON
Power ON
Power OFF
Short Press (1 sec)
Long Press (3 sec)
While device is OFF

USER GUIDE mobiWAN ENG
Follow the steps below when pairing the headset with mobile device for the first time.
I. Switch ON Bluetooth on the mobile device.
II. Press the Power Button for 1 second, a White LED will indicate the device is On.
After 5 seconds, pairing mode will start automaticall with flashing Blue LED .
III. Find the mobiWAN 4-digit unique identifier on the backside of the Main device
(ex.“mobiWAN_0227”).
IV. Go to the mobile device’s Bluetooth settings to search and add the mobiWAN device.
When paired the LED will blink Blue.
The steps above to Pair to the mobile device are onl required once. Once correctl
paired the mobiWAN will automaticall connect to the mobile device after the first few
seconds of being powered on.
CONNECTING TO THE MOBILE DEVICE
I.
Bluetooth On
II. III.
0227
IV.
mobiWAN_0227
PAIR
CANCEL
Long Press

USER GUIDE mobiWAN ENG
HEADSET / RADIO MODE
mobiWAN has different settings to optimize performance depending on if you are using
the device with either a smart device, such as a mobile phone or tablet or a walkie talkie
radio.
To toggle between the two modes hold the Left utton after start up and you will
hear the voice prompts for the mode selection changes
Depending on which mode you are using the Left utton will provide different
functionality (see table below)
Long Press Toggle Radio/Headset Mode
Upon Starting Up Device
Short Press
Left Button
Toggle Radio/
Headset Mode
N/A N/A
Toggle Radio/
Headset Mode Quick Message Quick MessageQuick Message
Toggle Mic On/Off Toggle Mic On/Off Toggle Mic On/Off
Long Press
Left Button
Laptop Not Connected mobiTALKCompanion App Radio

USER GUIDE mobiWAN ENG
MIC ON/OFF
The Left Button on the mobiWAN allows you to send MIC commands to supporting
apps such as Mobilus mobiTALK and other conferencing apps. 
1. A single tap of the Left Button turns ON and OFF the MIC control. Tap once to
initiate MIC ON and then tap again once to turn MIC OFF.
2. Alternatively tap and hold the Left Button for more than 1 second and MIC
transmission will turn ON. Once the button is released the MIC will turn OFF. When Left
Button is on hold for more than 52 seconds, MIC will turn OFF automatically. 
For conferencing apps such as Microsoft Teams and others, the following procedure is
recommended: 
1. Join the Teams call or conference on your host device (smartphone, tablet etc) as
normal and unmute your in app microphone. You will use the mobiWAN MIC
2. A single tap of the Left Button turns OFF and ON the MIC control. Tap once to
initiate MIC ON and then tap again once to turn MIC OFF.
3. Alternatively tap and hold the Left Button for more than 1 second and MIC
transmission will turn ON. Once the button is released the MIC will turn OFF. controls to
mute and unmute yourself.
Short Press
Press and Hold
While Talking Quick Message
Toggle Mic On/Off

USER GUIDE mobiWAN ENG
ENVIRONMENT PROFILE
mobiWAN has different microphone settings depending on the level of noise present in
the environment in which you are operating. You can toggle between 'QU ET mode',
'NORMAL mode' and 'NO SY mode' by pressing both the Left and Right buttons
at the same time. We recommend primarily using 'NORMAL mode' and switching to
'NO SY mode' when entering particularly high noise environments.
Toggle Between
Environment Profiles
Simultaneous
Button Press
QUIET NORMAL NOISY

USER GUIDE mobiWAN ENG
VOLUME CONTROL
The volume of the mobiWAN can be controlled two ways:
1. Directly by the volume up and down buttons of the mobile device
2. By separate single taps of the Right Button which will increase the volume up to
the Max Volume at which point you will hear beeps. 
3. To Reset the volume to the lowest volume, Long Press Right Button f or 1 second to
return to the lowest volume level.
Short Press
Long Press Reset to Lowest Volume
Increase in Volume

USER GUIDE mobiWAN ENG
DEVICE STATUS UPDATE
Double pressing on the Right button will provide you (via audio update) information
about the battery level of your device, and if you have the MI command set to the ON
or OFF status.The following board shows all the info possible under each category:
Double Press “Device Status Update”
“High
“Medium
”Low”
“On
”Off” “Noisy “Normal
“Quiet”
MIC
battery env. profile

USER GUIDE mobiWAN ENG
RESET BLUETOOTH CONNECTION
To pair the mobiWAN to a new device you can choose to hard reset the bluetooth pairing
on the mobiWAN. To do this hold the Power Button for longer than normally required
(5 seconds) on power up you will then hear the voice prompt say 'RESET' indicating that
the bluetooth functionality is ready for pairing to a new device.
Long Press Reset Bluetooth
While device is OFF

USER GUIDE mobiWAN ENG
Power ON
Solid hite
Solid Red
Power OFF
Fast Blinking Blue
Pairing / aiting to Pair
Blinking 2x Blue
Connected
Blinking 2x Red
Low Battery
LED INDICATORS
'The LED indicator above the Power button provides information on the status of
the mobiWAN through lighting colours and 'blinking' effects. This includes operations
with the device in use, such as Bluetooth connection.

USER GUIDE mobiWAN ENG
CHARGING
Plug th h ads t through th Charging Port into a 5V USB pow r charg r using a
USB - C cabl . Full cha rg t ak s 2-3 h ours.
Whil th d vic is charging, th LED will r main a st ady R d Colour. Onc fully
cha rg d th LED will chan g t o a st a dy Wh it colour.
Th mobiWAN d vic should only b charg d with a charg r rat d b low 15W
Plugged USB-C cable
Solid Red
Charging
Solid White
Charge Complete

USER GUIDE mobiWAN ENG
 Not powering on
 Powers on & q ickly t rns off
 Abr ptly t rns off
 “Battery Low” a dio message
Charge the headset using the USB-C cable provided with the mobiWAN.
TROUBLESHOOTING
 Not pairing Reset both the mobile device and mobiWAN device.
 No so nd Confirm the mobiWAN device is properly paired and connected to the mobile device
Alternatively confirm that the mobile device audio is not muted and/or increase volume.
This is not household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical equipment.
For any questions or concerns contact
[e-mail]
Design in London / Manufactured in the UK
Problem Action