Panasonic KX-HTS Series User manual

Setup Reference guide for KX-HTS Series
(Tested with HTS824 Version 1.5)
“LCR” SIP Trunk service
with Built-in Router
Version 0.1(PSN) 22th.June, 2017
Draft Version

2
SUMMARY
This document is a reference for configuring “LCR Telecom” SIP trunks onto Panasonic HTS and
includes the settings required for Incoming Call DDI routing and Outgoing Call CLI presentation.
SIP trunk specific account details are provided to you by LCR Telecom.
Attention:
This document was created based on the results of test environment accounts.
Panasonic cannot guarantee SIP Trunk operation in all environments, however as a result of
completing this Inter-Operability Test Panasonic will provide technical support for any issues
experienced an assist as far as possible in providing a resolution.
Please obtain relevant information from Service provider before configuration of SIP trunks.
Panasonic will not be held liable for any information provided in this guidance document.
Information used in this document is for interoperability testing.
Information and Specifications in this document are subject to change without notice.
Note
CLIR
HTS and LCR do not support CLIR (Anonymous).
CLIP when Transfer/Forward to CO
LCR does not support to notify the call originator CLI when call Transfer/Forward to CO.
Table of Contents
(1) SIP Trunk, Extension Port Number and NAT Configuration: Page 4
(2) Network Settings: Page 5
(3) Trunk Port Attribution: Page 7
(4) Provisioning a SIP trunk: Page 8
(5) Incoming Call Routing: Page 12
(6) Outgoing Call CLI: Page 13
(7) CLIR Outgoing Call (Anonymous calls): HTS Not supported Page 14

3
Built-in Router Example
HTS has a Built-in Router functions so advanced routing configuration can be managed by
the HTS and the internet router/modem simply providing internet access.
WAN Network: 10.0.0.0 / Subnet Mask: 255.255.255.248 (/24)
PBX assigned WAN-1 IP: 10.0.0.1
WAN Gateway IP Address: 10.0.0.6
Static DNS: Primary DNS Server 8.8.8.8 / Secondary DNS Server: 8.8.4.4
Note
Configure the settings according to the IP address system of the mapped WAN.
Also, set the IP address which does not duplicate other IP devices.
Internet
To Router/Modem
To PC/HUB
LAN1: 192.168.0.101/24
WAN1: 10.0.0.1/29
Router/Modem
PC
(Enable DHCP)
KX0HDV series
(e.g., KX-HDV230)
HUB
(Gateway: 10.0.0.6/29)
WAN Directly Connected Network
(10.0.0.0/29)

4
(1) SIP Trunk, Extension Port Number and NAT Configuration
SIP Extension & SIP Trunk Common
Select [PBX Configuration] - [2. Extension] - [7.SIP Extension Property]
[SIP Extension & SIP Trunk Common]
1. Voice (RTP) UDP port No.(Server): Leave at 12000-
2. SIP Port Number: Leave at 5060
3. NAT Traversal: Leave Off
4. NAT – Fixed Global IP Address: Leave at 0.0.0.0
All other settings can be left at default.
Click [ Apply ]
Click [ Apply Now ]

5
(2) Network Settings
Network Configuration WAN Setting
Select [Network Configuration] - [3.WAN]– [1.WAN Setting] and Select [WAN 1 Channel]
Click [Modify]
HTS WAN-1 IP: 10.0.0.1 (Example)
Select the appropriate the Connection Type. In this example, use the Static IP address Option.
1. WAN Type: Fix IP
2. WAN Connection Name: Leave WAN1_Fix_IP - Reference only-
3. IP address, by your ISP: Enter your actual IP address
4. Subnet Mask: Enter your appropriate subnet mask
5. ISP Gateway Address: Enter the actual Gateway IP address
6. Static DNS Change to Enable
7. Primary DNS Server: Enter the actual DNS IP address
8. Secondary DNS Server: Enter the actual Secondary DNS IP address
Click [Apply]

6
LAN Settings
Go to [Network Configuration] - [4.LAN] - [2.LAN Settings]
1. IP Address: 192.168.0.101
2. Subnet Mask: 255.255.255.0
3. DHCP Mode: Server
[ DHCP server ]
4. IP Pool Staring Address: Leave 192.168.0.102
5. IP Pool Ending Address: Leave 192.168.0.254
6. Lease Time: Leave One day

7
(3) Trunk Port Attribution
Select [PBX Configuration] -[3.Trunk]- [1.Port] and click [Edit / CO Line Number 1 to 8]
[CO Line Number 1]
1. Attribution: SIP Carrier - 1
2. Trunk Group: Leave at 1
Click [Apply]
Click [Apply Now]
Example, Configure “CO-Line 1-2: SIP Carrier-1, Other CO-Line: No Connect”
SIP Trunk 2 Channels
Others 6 CO Line are not used,
Configure to No Connect from
Analog Line.

8
(4) Provisioning the SIP Trunk
SIP Trunk Property - Common
Select [PBX Configuration] - [3.Trunk] - [7. SIP Trunk Property] - [Common]
1. DNS SRV Record Resolve Ability: Leave Disable
[Register]
2. Register Sending Interval (s): Leave at 3600
3. Register Resending Interval (s): Leave at 300
4. RTCP Sending Interval (s): Leave at 5

9
SIP Trunk Property continued – SIP Carrier-1
[SIP Carrier-1]
1. Provider Name: Enter a name – reference only
2. SIP Server Name: trunksip2.lcrcom.es
3. SIP Server IP Address: Leave at 0.0.0.0
4. SIP Server port Number: 4399
5. SIP Server Domain: Not required
6. Subscriber Number: Not required
[Account]
7. User name:
Enter the User name as supplied by LCR Telecom
(Note this is user name without @trunksip2.lcrcpm.es)
For example: Account (User name) =LCR201705301234567
Enter: LCR201705301234567
8. Authentication ID: Enter the Authentication ID as supplied by LCR Telecom
(Note this is user name without @trunksip2.lcrcpm.es)
For example: Authentication ID = LCR201705301234567
Enter: LCR201705301234567
9. Authentication Password:
Enter the Authentication Password as supplied by LCR Telecom
For example: Authentication Password = passwordABCD
Enter: passwordABCD
[Register]
10. Register Ability: Enable

10
SIP Trunk Property continued – SIP Carrier-1
[Calling Party]
1. Header Type: Leave From Header
2. Host Name: Leave BLANK
3. Format: Leave Without “+”
4. Send CLIP of caller when call from SIP Leave Enable
Carrier is forwarded to same SIP carrier: *CLI will be converted to PBX No by LCR
[Called Party]
5. Format: Leave Without “+”
[Voice]
1. IP Codec Priority 1st: Leave G.711A
2. IP Codec Priority 2nd: Leave G.711Mu
3. IP Codec Priority 3rd: Leave None
4. Packet Sampling Time: Leave at 20 (ms)
5. DTMF: Leave Outband (RFC2833)
6. Payload Type (DTMF): Leave at 101

11
SIP Trunk Property continued – SIP Carrier-1
[Session]
9. Session Timer Ability: Leave Enabled (Passive)
10. Session Expire Timer: Leave at 180
11. Session Incoming Refresher Request: Leave UAC
12. Session Refresh Method Leave re-INVITE
[DSP]
Leave Default
[Option]
Leave Default
Click [Apply]
Click [Apply Now]
Save the System data
Click [Save & Logout]

12
(5) Incoming Call Routing
DDI Table
[PBX Configuration] - [3.Trunk] - [3.DDI]
1. DDI Number: Enter the DDI number in the format (as below)
Example Landline Number: 910 123 001
Enter: 913123001
2. Name: Determined by the installer (optional setting)
3. Destinations: Determined by the installer (extension number, group etc)
Click [Apply]

13
(6) Outgoing Call CLI
CLIP
[PBX Configuration] - [Target Extension] Click (Example: Extension 101)
[Port - Extension 101 / CLIP]
1. Extension Name: HTS Ext Name101 (Example)
2. SIP Carrier -1: 910123001 (Example)
Click [Apply]
Click [Apply Now]
Click [Save & Logout]

14
(7) CLIR Outgoing Call (Anonymous calls)
*Note: HTS does not support CLIR as function.
END OF DOCUMENT