MOBILUS COSMO G3+ User manual

User manual of
COSMO | G3+ controller. www.mobilus.pl

1. GENERAL INFORMATION
COSMO | G3+is a 4-channel remote control, designed for remote control receivers brand
MOBILUS (radio remote controls for roller shutters, awnings, blinds / control modules for
motors without radio communication module / ON / OFF modules).
• Support of 4 channels.
• Support 4 channel groups.
• Bi-directional communication - the opportunity to receive additional feedback information
from receivers.
Please refer to the instruction manual that tells how to safely use the device. You are solely
responsible for any damages resulting from the using the device in a manner inconsistent with
its intended purpose. The manufacturer accepts no responsibility for damage or injury caused
by misuse, improper handling and running.
2. CONTENTS OF THE PACKAGE
The packaging contains the following items:
• remote COSMO | G3+,
• 1 CR2450 3 V battery in remote,
• user manual.
3. TECHNICAL PARAMETERS
• 4 channels remote
• Dynamic code
• FSK modulation
• 868 MHz
• Bi-directional communication
• 1 CR2450 3 V
• Dimensions: 75 x 45 x 14 mm / waga: 30 g
2

4. POWER SUPPLY
The device is powered by single battery CR2450. In order to change the battery, open housing
of the remote.
1. Between the lower and the upper part of the housing slide flat, rigid tool in the position
shown in Fig. 4a.
2. Then, slowly and firmly spread apart the two housing parts - Fig. 4b.
3. In the lower part of the housing is a battery holder CR2450 3 V - Fig. 4c.
Replace the old battery with a new one, pay attention to the polarity.
4. Close the remote control.
Fig. 4a Fig. 4b
Fig. 4c
3

5. DESCRIPTION OF THE REMOTE CONTROL
1
2
34
6
8
75
1. Pendant.
2. LED’s indicating the selected channel.
3. LED’s indicating radio transmission (blue, red).
4. Control button UP ( TURN ON for modules ON/OFF ).
5. Navigation channels button LEFT.
6. STOP button ( TURN ON/TURN OFF for modules ON/OFF; UP/STOP/DOWN in case of the
modules operating in steps mode ).
7. Navigation channels button RIGHT.
8. Control button DOWN ( TURN OFF for modules ON/OFF ).
4

6. READING OF REMOTE INTO THE MOTOR’S MEMORY
WARNING! Do not program the remote control when the shutter is in the extreme position (top
or bottom). Each program and changes of motor’s operation directions are confirmed by two
micro-movements of the driver.
Failure to comply with these rules may result in damage the blinds (inhaled by the housing).
1. Press the LEFT / RIGHT to select the appropriate channel.
Fig. 6a
1 channel 2 channel 3 channel 4 channel
Enter MOBILUS motor, serie R in the PROGRAMMING MODE OF MASTER REMOTE:
- press for 5 seconds PROGRAMMING BUTTON in the motor - Fig. 6b;
-
or double turn off and turn on the power supply od the motor - Fig. 6c;
The confirmation of properly performed operation will be two micro-movements of the motor driver - Fig. 6d.
Fig. 6b
a b c
5 s.
ON OFFON OFF
2x
Fig. 6c
ON OFF
2x
Fig. 6d
ON OFF
2x
5

WARNING! The first remote control readed into the receiver is a remote control MASTER. It
allows you to operate motor and enter it in the PROGRAM MODE OF OTHER REMOTES.
3. On the remote control simultaneously press the STOP and UP - Fig. 6d. 4 LEDs start
blinking – Fig. 6e. Hold the buttons until the motor driver will perform two micro-move-
ments. The remote control has been readed into the motor.
Fig. 6d
a
b
Fig. 6e
a
b
7. READING IN OTHER REMOTE
1. On the MASTER remote control simultaneously press the STOP button and UP - Fig. 7a.
4 LEDs start blinking - Fig. 7b. Hold the buttons until the motor driver will perform two
micro-movements confirming the input of the motor in the PROGRAM MODE.
Fig. 7a
MASTER
MASTER
Fig. 7b
MASTER MASTER
6

2. On the second remote control, you want to program, press the STOP and UP - Fig. 7c.
Hold the buttons until the motor driver will perform two micro-movements -Fig. 7d.
Another remote was loaded into the motor.
rys. 7c
PILOT 2
PILOT 2
rys. 7d
Within 20 sec. you can proceed to load the next remote. However, if no action of programming
at this time doesn’t happen, motor automatically returns to the OPERATING MODE. You can
expedite return to the OPERATING MODE manually using the remote control MASTER. In this
case, press the button on the STOP and UP and hold more than 5 seconds. In both cases, return
to the OPERATING MODE will be confirmed by two micro-movements of the driver.
8. BI-DIRECTIONAL COMMUNICATION
Remote control COSMO | G3+enables bi-directional exchange of information with the receiver /
receivers (sends and receive messages).
This feature allows you to control the state of blinds, check whether they have been properly lowered
or raised as to whether there is damage to be checked (eg. due to interference by third parties).
Correct functioning of bidirectional communication requires:
- use of the receivers with bidirectional communication,
- programming one channel only for one receiver,
- the correct channel configuration - setting for bidirectional communication channel,
- ensure seamless communication of the remote control with the receiver.
Receivers supporting the bidirectional communication: MOBILUS: M35 _ER_, M45 _ER_.
7

9. BI-DIRECTIONAL COMMUNICATION - ACTIVATION / DISACTIVATION
1. Select the channel for which you want to enable / disable bidirectional communication.
2. Press the buttons STOP and LEFT and hold them for 5 seconds until 4 LEDs light up
signaling radio transmission. Blue color -bidirectional communication enabled - Fig. 9a.Red
- bidirectional communication disabled - Fig. 9b.
Fig. 9a Fig. 9b
10. BI-DIRECTIONAL COMMUNICATION - READING OF POSITION
As long as bi-directional communication is enabled, the remote control COSMO | G3+ will expect
to send information about the state from the receiver. After receiving feedback on the remote will
turn on the LEDs. Due to the battery consumption waiting time for feedback has been limited to
20 seconds.
8

a- upper LEDs blink in blue - blind / gate is located in the top position.
b- lower LEDs blink in blue - blind / gate is located in the lower position.
c- LEDs blink diagonally in blue - the blind is located in the area between the upper and lower limit
switch.
d- top and lower LEDs blink red light - the additional sound signal - error occurred - blind
encountered an obstacle.
It is possible to query the receiver about its current status. Please select the channel and press
STOP. The remote will send a question to the receiver. Upon receipt of the response it displays its
status.
11. CHANGE OF MOTOR’S OPERATION DIRECTION
After loading the remote control to the motor check that the buttons UP and DOWN correspond
to lifting and lowering the blinds - Fig. 11a.If not, press simultaneously buttons STOP and
DOWN and hold them for about 5 seconds on the remote control any loaded to the motor. The
confirmation of correctly performed operation are two micro-movements of the driver - Fig. 11b.
The motor changes the direction of the work on the correct - Fig. 11c.
Fig. 11
abc
WARNING ! You can change the direction of the work of motor for MOBILUS drives with electronic
limit switches only before setting the upper and lower limit switches. You can change the direction
of work for the MOBILUS motors with mechanical limit switches at any time.
9

12. ENVIRONMENTAL PROTECTION
This appliance is marked according to the European Directive on Waste Electrical
and Electronic Equipment (2002/96/EC) and further amendments. By ensuring this
product is disposed of correctly, you will help to prevent potential negative consequ-
ences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. The symbol on the product, or the do-
cuments accompanying the product, indicates that this appliance may not be treated
as household waste. It shall be handed over to the applicable collection point for the
waste electrical and electronic equipment for recycling purpose. For more information
about recycling of this product, please contact your local authorities, your household
waste disposal service or the shop where you purchased the product.
10