Mobital LUNAR User manual

ASSEMBLY INSTRUCTIONS
GENERAL NOTE: CAREFULLY REMOVE ALL WRAPPING MATERIALS AND ENSURE ALL PARTS
ARE ACCOUNTED FOR. ASSEMBLE ON A CLEAN FLAT SURFACE TO AVOID SCRATCHES. DO NOT
DISCARD THE PACKAGING UNTIL ITEM IS FULLY ASSEMBLED.
LUNAR
STORAGE BED
ITEM:
HARDWARE LIST
ITEM QTY DESCRIPTION DESCRIPTIONNO. QTY
A 2
B 4
Headboard legs ( pre-
attached to headboard)
50 mm bolt ( pre-
attached to headboard)
C 4 Frame leg
H 6
I 56
Cross bar
M8 - 30MM
K 1 M8 - 20MM
L 6 M8 - 40MM
M 1 Bed draw strap
J 1 Y8
D 2 A-45 Bracket
E 1 B-45 Bracket
F 6 D-45 Bracket
G 2 Hydraulic
1. Follow each step of instructions in the correct order, if not, assembly difficulties will occur and can result in injury and/or
damage to the product.
2. For your safety, assembly by two (2) people is highly recommended.
3. Use the parts and hardware list below to identify and separate each of the pieces included.
4. Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may cause the bolts to misalign
during assembly.
5. If using power tools to aid in assembly, please use caution. Power tools can damage the hardware and/or the product itself,
which will void the warranty.
6. For the hydraulic system to work safely and properly, complete the bed with a mattress weighing maximum 220 lbs.
COMPLETED ASSEMBLY
PAGE 1 OF 5
TOOLS NEEDED
+
*Tip for attaching fabric cover - Peel away the velcro cover as you make your way across from the top, then pulling
firmly at the bottom and attaching in the same way. Start at the outside corners and make your way to the headboard
so there is enough extra leeway to have the rail tuck into the headboard.

CENTER SUPPORT BAR
I
C
F
SIDE RAIL
FOOTBOARD
STEP 1
ASSEMBLY INSTRUCTIONS
GENERAL NOTE: CAREFULLY REMOVE ALL WRAPPING MATERIALS AND ENSURE ALL PARTS
ARE ACCOUNTED FOR. ASSEMBLE ON A CLEAN FLAT SURFACE TO AVOID SCRATCHES. DO NOT
DISCARD THE PACKAGING UNTIL ITEM IS FULLY ASSEMBLED.
LUNAR
STORAGE BED
ITEM:
STEP 2 INSTRUCTIONS:
• ATTACH CROSS BARS (H) TO CENTER
SUPPORT BAR BY M8-30MM BOLT (I).
STEP 1 INSTRUCTIONS:
•ATTACH FRAME LEG (C) TO D-45
BRACKET (F) BY M8-30MM BOLT (I)
AND THEN ATTACH TO HEADBOARD
AND SIDE RAIL BY M8-30MM BOLT (I).
•ATTACH FRAME LEG (C) TO D-45
BRACKET (F) BY M8-30MM (I) AND
THEN ATTACH TO FOOTBOARD AND
SIDE RAIL BY M8-30MM BOLT (I).
I
H
STEP 2
PAGE 2 OF 5
HEADBOARD
SIDE RAIL

ASSEMBLY INSTRUCTIONS
GENERAL NOTE: CAREFULLY REMOVE ALL WRAPPING MATERIALS AND ENSURE ALL PARTS
ARE ACCOUNTED FOR. ASSEMBLE ON A CLEAN FLAT SURFACE TO AVOID SCRATCHES. DO NOT
DISCARD THE PACKAGING UNTIL ITEM IS FULLY ASSEMBLED.
LUNAR
STORAGE BED
ITEM:
STEP 3 INSTRUCTIONS:
• ATTACH CROSS BARS (H) TO SIDE
RAILS BY M8-30MM BOLT (I).
I
H
STEP 3
STEP 4 INSTRUCTIONS:
• PLACE FLOOR PANELS ON TOP OF
CROSS BARS (H).
STEP 4
FLOOR PANEL
PAGE 3 OF 5
SIDE RAIL

ASSEMBLY INSTRUCTIONS
GENERAL NOTE: CAREFULLY REMOVE ALL WRAPPING MATERIALS AND ENSURE ALL PARTS
ARE ACCOUNTED FOR. ASSEMBLE ON A CLEAN FLAT SURFACE TO AVOID SCRATCHES. DO NOT
DISCARD THE PACKAGING UNTIL ITEM IS FULLY ASSEMBLED.
LUNAR
STORAGE BED
ITEM:
STEP 5 INSTRUCTIONS:
•ATTACH B-45 BRACKET (E) TO
CENTER SUPPORT BAR AND FOOT-
BOARD BY Y8 BOLT AND FASTENER (J)
AND M8-20MM BOLT (K)
STEP 5
STEP 6
FOOTBOARD
CENTER SUPPORT BAR
E
J
K
STEP 6 INSTRUCTIONS:
•ATTACH A-45 BRACKET (D) TO HEAD-
BOARD AND SIDE RAILS BY M8-30MM
BOLT (I); ATTACH D-45 BRACKET (F) TO
FOOTBOARD AND SIDE RAILS BY
M8-30MM BOLT (I)
PAGE 4 OF 5
I
D
HEADBOARD
SIDE RAIL
F
SIDE RAIL
FOOTBOARD
I
• *NOTE* PLEASE MAKE SURE
FOOTBOARD AND SIDE
RAILS ARE ALIGNED BEFORE
TIGHTENING SCREWS.

ASSEMBLY INSTRUCTIONS
GENERAL NOTE: CAREFULLY REMOVE ALL WRAPPING MATERIALS AND ENSURE ALL PARTS
ARE ACCOUNTED FOR. ASSEMBLE ON A CLEAN FLAT SURFACE TO AVOID SCRATCHES. DO NOT
DISCARD THE PACKAGING UNTIL ITEM IS FULLY ASSEMBLED.
LUNAR
STORAGE BED
ITEM:
PAGE 5 OF 5
STEP 7
STEP 7 INSTRUCTIONS:
• ATTACH HYDRAULICS (G) TO SIDE
RAILS BY M8-30MM BOLT (I)
I
G
SIDE RAILS
LSPRING FRAME
STEP 8 INSTRUCTIONS:
• ATTACH SPRING FRAME TO
HYDRAULICS (G) BY M8-40MM BOLT
AND NUT (L)
• *TIP* ATTACH THE BED DRAW
STRAP (M) INCLUDED IN THE
PRODUCT TO THE MIDDLE END
OF THE SPRING FRAME FOR
EASY LIFT-UP.
To avoid any damage on the hydraulics and bed, please do not pull down the spring frame without putting the
mattress on first as the added counterweight will help alleviate the motion and mechanism on the hydraulics. Any
damages caused by forcefully pulling down the spring frame by itself will void the warranty. Maximum weight
capacity is 220lbs. Do not allow children to play inside the storage bed. Improper use of product can result in
serious injury or death.
CAUTION/WARNING:
STEP 8