Mobotix MX-Keypad1-EXT User manual

EN
Quick Install KeypadRFID
www.mobotix.com
HiRes Video Innovations
The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its decen-
tralized concept has made high-resolution video systems cost-ecient.
MOBOTIX AG • D-67722 Langmeil • Phone: [phone] • Fax: [phone] • [email protected]
Security-Vision-Systems
MX-Keypad1-EXT
31.468-005_EN_08/2015
Keypad with Contactless
RFID Technology
Module for MOBOTIX IP Video Door Station
Keyless access to buildings using RFID transponder
card or PIN code
• Keypad module with 1 admin and 5 user RFID cards
• Mailbox control
• Integrated RFID technology for keyless entry
• Available colors: white, silver, dark gray, black, amber
• Up to 60hrs backup power supply using DoorMaster
(accessory)
Click
1
2
Installing the KeypadRFID
Installing the module follows the procedure described in the T24 System Manual
Part1, in Section 2.4.2, "Installing the KeypadRFID" . For more information on other
connection variants (e.g. without DoorMaster), please see Section 2.1, "Overview:
Connection and Wiring Diagrams" .
When installing the module in the frame, make sure that you insert the right side
of the module first and then press on the left edge (and not on the center) to
click the module into place.
Operation
After installing, make sure that you follow the steps in the T24 System Manual Part2 in Section 2, "Initial Operation
without PC" . This chapter shows you how to configure the entire system (including the RFID admin and user cards)
in a few simple steps.
Replacing the KeypadRFID
If the KeypadRFID needs to be replaced against all expectations, you need a current backup of the system
configuration. This will ensure that you can seamlessly integrate the new KeypadRFID into the system later on.
Please follow the steps outlined in the T24 System Manual Part2 in Section 5.2, "Backup & Restore" .
To dismount the KeypadRFID, follow the steps in the
T24 System Manual Part1 in Section 2.4.6, "Removing and
Exchanging Modules" . Make sure that you deactivate the theft protection before dismounting the module and
that you activate the theft protection again after re-installing.
MOBOTIX KeypadRFID
MX-Keypad1-EXT
(in triple frame silver)
RFID cards
for keyless entry included
(1 admin card, 5 user cards)
I/O terminal
Sealing plug
Seal
MxBus terminal
Back view with cover removed
Outdoor Indoor
Door
2
6
MxBus (YSTY 0.8 mm – max. length: 50m/55yd)
Theft protection (YSTY 0.8 mm – max. length: 50m/55yd)
Door opener, door sensor, lock sensor
(YSTY 0.8 mm – max. length: 50m/55yd)
DoorMaster
IP Video Door Station
2
For additional information on the other connection variants and for installing,
see the T24 System Manual Part1 on www.mobotix.com > Support> Manuals.
KeypadRFID
InfoModule
Standard Connection: KeypadRFID with
IP Video Door Station, InfoModule and DoorMaster
Weatherproof (IP65)
–30 to +60 °C/–22 to +140 °F

EN
Quick Install KeypadRFID
www.mobotix.com
HiRes Video Innovations
The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its decen-
tralized concept has made high-resolution video systems cost-ecient.
MOBOTIX AG • D-67722 Langmeil • Phone: [phone] • Fax: [phone] • [email protected]
Security-Vision-Systems
 2013 • Declaration of Conformity: www.mobotix.com> Support> MX Media Library> Certificates
Copyright © MOBOTIX AG 2015 • Made in Germany • Technical information subject to change without notice.
Operation: Keys and Signaling
Leave a message (standard mailbox)1
Press envelope key> welcome message plays> keep
envelope key pressed and leave message
Play back messages*1
Hold up user card> keys 0to9 are blinking: 0to9 new
messages> play back with key 0to9
Record new welcome message for mailbox*1
Press OK/MENU and hold the key> hold up user card>
press bell key> press bell key again> keep envelope
key pressed and leave message> let go of envelope
key> welcome message is activated
1Only in combination with MOBOTIX IP Video Door Station.
Welcome Message
keep
pressed
hold
Messages
0 9
Zutritts PIN
OK
hold
keep
pressed
keep
pressed
Open door with blue user card
Hold up user card> door is unlocked
Open door with PIN code
Enter PIN code> press key button> door is unlocked
Open door on power failure (red LED is
blinking)2
Press ESC/ALARM (until illumination is on)> opening door
with card or PIN is now possible for about 10seconds
2Only in combination with MOBOTIX DoorMaster.
PIN code
0 9
Zutritts PIN
keep
pressed
ESC
hold (2nd beep)
Technical Specifications
Interface MxBus
Inputs 2 galvanically separated inputs
(AC/DC, self-powered, up to 50V)
Outputs 1 isolated relay output (AC/DC, up
to 50V/60W/2A)
Protection class IP65 (DIN EN 60529)
Operating
temperature
–30 to +60 °C/–22 to +140°F
(DIN EN 50155)
Power Supply MxBus
Power consumption Typically 1W
RFID cards: Type/
Encryption
MIFARE DESFire EV1
3K3DES/AES
Notes
• Please follow the notes on installing and operating the device in the T24 System Manual (www.mobotix.com in
the Support> Manuals section). This manual also contains wiring diagrams for the dierent scenarios.
• The MOBOTIX KeypadRFID is only to be used in the original frames of the IP Video Door Station.
• Before Installing, make sure that the seal on the back of the KeypadRFID has been properly attached.
• When inserting the module into the frame, only press at the edges, never at the center of the module.
• Make sure the device is not operated outside of its operating temperature range of –30 to +60°C/–22 to +140°F.
• BellRFID and KeypadRFID can only be used on one MxBus with a later software version of the camera.
99mm/3.9in
99mm/3.9in
MOBOTIX KeypadRFID
Order no.: MX-Keypad1-EXT
Open door, messages,
doorbell
Function keys
10-key keypad
Admin card
Order no.: MX-AdminCard1
(1 included)
User card
Order no.: MX-UserCard1
(5 included)
MOBOTIX RFID cards
Status LED
On Normal status
On Device error
Blinking Power failure
SealCover
Status LED
/
Dimensions Back
Left LED (green/
red, status LED) Right LED (blue)
*Only for cards with activated mailbox feature – see
T24 System Manual Part2, «Adding User Cards»