Mobotix P25 Instructions for use

Innovations–Made in Germany
The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its decentralized concept has made
high-resolution video systems cost-ecient.
MOBOTIX AG • D-67722 Langmeil • Phone: [phone] • Fax: [phone] • [email protected]
EN
Quick Install Indoor Camera p25
Security-Vision-Systems
32.356-001_EN_06/2015
MX-p25
www.mobotix.com
• Includes MxAnalytics video analysis tools out-of-the-box
• Recording on internal MicroSD card (SDXC)
• Signal Input/Output and MxBus via optional MX-Bus-IO-Module
• Optional audio version with microphone and speaker
• Sensors for temperature, illumination, shock detection integrated
• Installation is as simple as installing a ceiling spotlight
p25 Standard Delivery
1.2
1.1
1.7
1.8
1.3
1.6
1.10
1.4
1.5
1.9
Item Count Part Name
1.1 1 Housing with spring clips and tiltable camera
receptacle (installed)
1.2 1 Back cover (installed)
1.3 1 Main board with lens mount (installed)
1.4 1 Lens (only installed in camera models listed in
«Variants of the p25» )
1.5 1 Blind cover (only when self-mounting the lens with
MX-p25-BOD1)
1.6 1 Ethernet patch cable, 50cm/19.7in, black (installed)
1.7 1 MicroSD card pre-installed (SDHC montiert, SDXC
supported)
1.8 1 Flat-head screwdriver, blue
1.9 1 Lens wrench red (only with MX-p25-BOD1 and
lenses D036 to D237)
1.10 1 Allen wrench 1.5mm
Removing/Installing the Back Cover
The steps listed below are only required if you need to access the inside of the camera housing. Make sure the power
supply to the camera is disconnected before opening the housing!
Caution: In order to avoid damage from electrostatic discharge, you should touch a grounded device before opening
the housing of the camera (e.g., the blank metal at the back of a computer). This will remove any static electricity that
may have built up.
1. Remove the cover
Remove the back cover of the p25 by insert-
ing a flat-head screwdriver into one of the
slots at the side as shown in the figure and
turning it slightly. Repeat the process for
the two other slots and lift the back cover
from the housing.
2. Follow the procedures
Follow the procedures for the work inside
the housing as described in the sections
listed below:
•
➔ Inserting/Exchanging the SD Card
• ➔ Installing the MX-Bus-IO-Module
3. If required, enlarge the cable guide
If the cable guide is not large enough for
additional cables, enlarge the guide accord -
ingly. Depending on the size required, break
out either one or two elements of the cable
guide using pliers (see blue markings in
the figure).
4. Attach back cover
Insert the back cover, so that the large arrow
(highlighted blue in the figure) is positioned
in the viewing direction of the camera. Make
sure the cables and wires are guided prop-
erly thought the cable guide, then carefully
press the back cover into the housing until
it clicks into place.
Installing the Lens (Only MX-p25-BOD1 Variant)
The steps listed below are only required if the p25 has been ordered with separate lens for self-mounting (see «Variants
of the p25» ).
1. Remove the blind cover
Remove the blind cover that protects the
image sensor during shipping from the
lens mount.
2. Install the lens
Screw the lens into the lens mount. Depend-
ing on the physical length of the lens, you
can use your hand and then the red lens
wrench (item1.9). After initial operation of
the camera, remember to adjust the focus of
the lens (see «Initial Operation of the p25» ).
+
Connecting the p25
Microphone
Receptacle for
adjusting the
camera tilt
Recording
Screw for
locking the
camera tilt
Power/Status
For information on connecting the p25, please see
the M25 Camera Manual , section «Network and
Power Connection, Additional Cables» .
Regarding the initial operation of the p25, please
see the
M25 Camera Manual in Chapter 3, «Initial
Operation» .
MOBOTIX 6MP camera for flexible use in indoor applications,
install as complete Indoor Camera p25 (Day or Night) with selected lenses
or as camera module p25 (Day or Night) with separate lens (MX-B036 to
MX-B237).
www.mobotix.com> Products> p25
Compact and Flexible Indoor Camera
for Ceilings
Inserting/Exchanging the SD Card
All camera models can use the integrated microSD card (SDXC) to record video data. In order to exchange the microSD card, please proceed as outlined
in the following instruction. For information on reliable SD cards, please see the MOBOTIX website www.mobotix.com> Support> MX Media Library>
Planning in the document MicroSD Card Whitelist for MOBOTIX Cameras .
When replacing the SD card, make sure that recording has been deactivated in the browser (
Admin Menu> Storage> Storage on External File Server/
Flash Device ; activate recording again in the same dialog). Follow the instructions in section «Removing/Installing the Back Cover» to access the inside
of the camera and to close it again after inserting the SD card.
1. Remove the SD card
If a microSD card has been installed, gently
press with your finger as indicated by the
arrow until you hear a click . Then release
the SD card. The card is protruding slightly
and can be easily removed.
2. Insert the SD card
Insert the microSD card and gently press
with your finger as indicated by the arrow
until you hear another click .
Make sure that the SD card is fully inserted.
Click! Click!
Can be tilted vertically
from –5° to –45°.
MOBOTIX p25 (Day) with lens MX-B036
MX-p25-D036
Installing the MX-Bus-IO-Module
For the p25, you can use the optionally available MX-Bus-IO-Module to attach MxBus devices (e.g., an
MX-GPS-Box), to attach external sensors using the signal inputs and to switch other devices via the signal
outputs. To facilitate the installation of the module, you should attach the connection wires before inserting
the module.
Follow the instructions in section
«Removing/Installing the Back Cover» to access the inside of the camera
and to close it again after inserting the module.
1. Attach the connection cables
Attach the connection cables as shown in the terminal connector overview.
Terminal Connectors
MxBus
connections MxBus
Output1A Relay
pot.-
free
–
Out-
puts
Output1B/GND Output1
12V self-
powered
Output112V –
Output2A Relay
pot.-
free
–
Output2B/GND Output2
12V self-
powered
Output212V –
Output1–
Inputs
Output1+
Output2–
Output2+
2. Insert the MX-Bus-IO-Module
Hold the MX-Bus-IO-Module with attached
connection wires over the receptacle on the
main board (red arrow in figure).
Use one finger to carefully press the board
of the module onto the receptacle. Make
sure that the green terminal connector block
is pointing upward (towards the SD card,
see red arrow in figure below).
Make sure that the MX-Bus-IO-Module is
fully inserted.
Please also make sure that the connection
wires are guided through the housing without
tension and in a loop so that the cables
do not lift the module out of its receptacle
when adjusting the camera tilt (see figure).
MX-Bus-IO-Module
for MxBus modules and
signal inputs/outputs
(accessory)
Variants of the p25
MX-p25-Day MX-p25-Night
6MP (3072x2048)
Color
6MP (3072x2048)
Black&White Variant
MX-p25-BOD1* MX-p25-BOD1-N* p25 camera module, for lenses MX-B036 to MX-B237
(f/1.8, 103° to 15°, self-mounted*)
MX-p25-D016 MX-p25-N016 p25 Hemispheric with Fisheye lens MX-B016
(f/2.0, 180° horiz. angle of view)
MX-p25-D036 MX-p25-N036 p25 with ultra-wide-angle lens MX-B036
(f/1.8, 103° horiz. angle of view)
MX-p25-D061 Self-mounted* with
MX-p25-BOD1-N
p25 with wide-angle lens MX-B061
(f/1.8, 60° horiz. angle of view)
MX-p25-D079 Self-mounted* with
MX-p25-BOD1-N
p25 with standard lens MX-B079
(f/1.8, 45° horiz. angle of view)
MX-p25-D119 Self-mounted* with
MX-p25-BOD1-N
p25 with tele lens MX-B119
(f/1.8, 31° horiz. angle of view)
MX-p25-D237 Self-mounted* with
MX-p25-BOD1-N
p25 with distance tele lens MX-B237
(f/1.8, 15° horiz. angle of view)
*Requires focusing after self-mounting the lens (see «Initial Operation of the p25» )
MX-p25-D/N...
MX-p25-BOD1* + lens
+

Innovations–Made in Germany
The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its decentralized concept has made
high-resolution video systems cost-ecient.
MOBOTIX AG • D-67722 Langmeil • Phone: [phone] • Fax: [phone] • [email protected]
EN
Quick Install Indoor Camera p25
Security-Vision-Systems
www.mobotix.com
 2015 • Declaration of Conformity: www.mobotix.com> Support> Media Library> Certificates
Copyright © MOBOTIX AG 2015 • Made in Germany • Technical information subject to change without notice.
Removing the p25
1. Pull out the camera
Pull the camera from its position by gently pulling the camera downward
on one side, then the other side.
Take care to NOT let the spring clips
snap forward (risk of injury!).
2. Remove the cables
Remove the cables coming from the building (network cable, USB cable,
MxBus and signal input/output wires). Pull out the camera.
Installing the p25
Use the drilling template on the back for this purpose (red circle) or draw a circle with 105mm/4.13in diameter for the
cut-out. Cut out the hole for the camera, then guide the cables (network cable, USB cable, MxBus and signal input/
output wires) through the hole.
1. Install the p25
Press the spring clips back and insert the
p25 into the hole for the camera. The spring
clips will snap outwards, thus firmly holding
the camera in place.
Make sure that you only press back the
spring clips as shown in the image. Do not
press them back any further as the springs
may snap out of their fixtures otherwise.
2. Roughly align the p25
Turn the camera until it roughly points into
the intended direction; once it is running, you
will adjust the camera according to the live
image (see «Initial Operation of the p25» ).
Initial Operation of the p25
The initial operation starts with connecting the power supply (see section «Network and Power Connec-
tion, Additional Cables» in the M25 Camera Manual ). The first access follows the procedure described in
the same manual in the section «Initial Operation of the Camera». All other tasks require access to the
camera’s user interface in the browser. Enter the camera’s IP address into the address bar of the browser.
1. Set installed lens (only when self-mounting)
Open Admin Menu> Hardware Configura-
tion > Lens Configuration dialog and select
the installed lens. This step is required to select
the proper special functions of the installed lens
(e.g., for wide-angle lenses).
2. Adjust lens focus (if required)
This step is only necessary if the lens has been
installed for the first time or exchanged. In cam-
eras with a MX-B016 ("Hemispheric") lens, the
lens has been focused at the factory.
Check the live image from the camera in the
browser. Activate the focusing aid in the browser (Focusing Aid quick
control, Activated value).
Carefully turn the lens in clockwise or counter-clockwise direction using
the red lens wrench until the red area of the focusing aid is as small as
possible. Remove the lens wrench every time you changed the lens focus.
Once the focus is adjusted properly, deactivate the focusing aid again
(Focusing Aid quick control, Disabled value).
3. Adjust viewing direction
Turn the image in the ceiling until the live image
shows the desired viewing direction 1.
Stick the Allen wrench (item1.10) into the hole of
the lock screw and loosen the screw a bit 2.
Stick the blue screwdriver
(item1.8) into the receptacle for adjust -
ing the camera tilt. Adjust the camera
tilt as needed while watching the live
image of the camera 1.
Lock the camera tilt by slightly tightening
the lock screw 2.
4.
Configuring and Using the MX-Bus-IO-Module
The camera will automatically detect an installed
MX-Bus-IO-Module (see Camera Status, System
section in browser).
The signal inputs can be used right away in the
signal input profiles in the Setup Menu> Event
Overview. Likewise, the signal outputs can be
used in the signal output profiles in Admin
Menu> Hardware Configuration> Signal Out Profiles.
In addition, the signal inputs/outputs have been entered automatically
in the Admin Menu> Assign Wires dialog and can be used to control
doors and lights.
To use one or both signal outputs not as potential-free outputs (for relays),
but as
self-powered 12V outputs , open the Admin Menu> Hardware
Configuration> Manage Hardware Expansions dialog. In the MxBus/
IO Board section, click on Connect for each output you want to use as
self-powered output.
5. Save the configuration
In the live image of the browser, select the Manage Settings quick control
ans set Store Entire Configuration as value. The camera stores the con-
figuration in the permanent camera memory so that the settings will be
applied at the next camera reboot.
Screw for
locking the
camera tilt
1
2
1
2
Output1
Output2
Important Notes
Safety Warnings
• This product must not be used in locations exposed to the dangers
of explosion.
• Make sure that you install this product as outlined in the installation
instructions above.
•
When installing this product, make sure that you are only using genuine
MOBOTIX parts and MOBOTIX connection cables.
• Only install this product in suitable, solid materials that provide for a
sturdy installation of the fixing elements used.
• When removing the camera from the ceiling, make sure that the spring
clips do not snap back (
risk of injury! ).
• Electrical systems and equipment may only be installed, modified and
maintained by a qualified electrician or under the direction and supervi-
sion of a qualified electrician in accordance with the applicable electri-
cal guidelines. Make sure to properly set up all electrical connections.
•
When attaching modules to the USB connector, the power consumption
of all attached modules must not exceed 1W .
• Due to the high performance of the p25, the area of the image sensor
can get quite hot , especially when the ambient temperature is also
high. This does not aect the proper functioning of the camera in any
way. This camera must not be installed within the reach of persons.
• Make sure the power supply to the camera is disconnected before
opening the camera housing (e.g., when exchanging the SD card).
• MOBOTIX products include all of the necessary configuration options
for operation in Ethernet networks in compliance with data protection
laws. The operator is responsible for the data protection concept across
the entire system. The basic settings required to prevent misuse can be
configured in the software and are password-protected. This prevents
unauthorized parties from accessing these settings.
•
Make sure that the operating temperature of 0 to +40 °C/+32 to +104°F
is not exceeded.
Legal Notes
You must comply with all data protection regulations for video and sound
monitoring when using MOBOTIX products. Depending on national laws
and the installation location of the p25, the recording of video and sound
data may be subject to special documentation or it may be prohibited. All
users of MOBOTIX products are therefore required to familiarize themselves
with all valid regulations and comply with these laws. MOBOTIX AG is not
liable for any illegal use of its products.
Technical Specifications
Since the p25 is identical to the M25 for the most part, the technical data listed in the M25 Camera Manual in Section Technical Data
also applies to this product. You can find the M25 Camera Manual as a PDF file on www.mobotix.com> Support> Manuals.
p25 (Dierences Compared to M25)
Lens Options MX-B016 to MX-B237 (180° to 15° hor. angle of view)
Max. Image Size 6MP in 3:2 format (3072x2048)
Audio Functions None; optionally with microphone and speaker
Interfaces
Ethernet 10/100, IPv4/IPv6, MiniUSB;
MxBus and inputs/outputs using optional
MX-Bus-IO-Module
Power
Consumption Typ. 4W
Operating
Conditions
IP20 (DIN EN 60529)
0 to +40 °C/+32 to +104° F (DIN EN 50155)
Max. Thickness for
Installation
Spring clips properly clamp down on materials from 1to
28mm/0.04 to 1.1in
Dimensions
Outside diameter 120mm/4.72in, total height
85mm/3.35in, height installed 46mm/1.81in, recom-
mended min. installation depth 50mm/1.97in
Materials Housing: PBT GF30
Weight approx. 270 g
MX-Bus-IO-Module
Inputs 2 galvanically separated inputs
(AC/DC, 0 to 48V)
Outputs
Variant1 (default): 2 potential-free outputs (max. load
per pin: max. 30W or max. 1A or max. 48V AC/DC)
Variant2 (set in browser): 2 powered outputs 12VDC;
max. 50mA per output
Add. Interfaces MxBus connections for MOBOTIX peripheral devices
Operating
Conditions Same as camera
Cross-sectional
area of wires at the
terminals
0.14 mm² – 0.5 mm² (AWG 21 – 26)
Power
Consumption Typ. 0.5W, max. 1.5W
Dimensions/Drilling Template
Outside diameter 120mm/4.72in
39mm/1.54in
46mm/
1.81in
Recommended
min. instal-
lation depth
50mm/1.97in
Max. thickness
for installation
28mm/1.1in
MX-Bus-IO-Module
p25 main board
Outside diameter 120mm/4.72in
25mm/0.98in
Cut-out diameter Ø105mm/4.13in