Modulex KNX PS-S.640.30.1 User manual

KNX POWER SUPPLY
PS-S.640.30.1
ОСНОВНЫЕ СВЕДЕНИЯ
Intelligent power supply for the KNX system with an additional auxiliary power output of 29V DC, with the
function of diagnostics of voltage in the KNX bus and protective against short circuit and overload .
• Compact housing (2TE)
• Additional output 29V DC
• Diagnostic function
• LED status indication
• Output current 640mA
• Leakage < 5W
• Mains voltage 230V AC 50Hz
• Overload and short circuit protection
• Bus line reset via local push button or remote
• DIN rail 35mm mounting
A. Supply voltage terminals B. Reset button C. Programming button D. Aux output connector E. KNX TP connector
1. LED input voltage V 2. LED bus voltage V 3. LED telegram traffic 4. LED output current I
IN BUS OUT
5. LED internal temperature 6. LED KNX reset 7. Programming LED
page 1
C
7
E
B
4
2
1
3
D
56
A
PASSPORT
МГРЛ-27.12.1931-008.01 ПС
Module Electronic LLC
module-electronic.ru, [email protected]
phone: [phone]

page 2
Device model
PS-S.640.30.1
Power input
Mains voltage
230V AC ± 10% 50Hz
Power consumption normal / max. overload
23W / 42W
Mains failure bridging time
> 100ms
Mains voltage connection
screw terminals 0,3...2,5mm²
Power output
KNX, AUX output voltage
28...31V DC
Rated current / max. current (total output)
640mA / 1,2A
Efficiency at nominal load
82%
KNX interface
Specification
TP-256
Available application soware
ETS 4 and later
KNX connector
4-wire EIB connector (PUSH WIRE spring clips) for standard
cable TP1 0,8мм Ø
KNX physical address by default
12.12.255
Operation temperature
-5°C ... + 45°C
Operation humidity
5 ... 95% (no condensation)
Degree of protection
IP 20, clean environment
Mounting type
DIN rail 35mm
Dimensions
36 х 90 х 71mm (2TE)
Weight
185g
1. Input voltage VIN
Green: Input voltage is 195...265V AC
Red: Input voltage is out of this range
2. Bus voltage VBUS
Green: KNX bus voltage 28...31V DC
Red: KNX bus voltage is out of this range
3. Telegram traffic
Green (blinking): Telegram traffic < 80%
Red: Telegram traffic > 80%
4. Output current I
OUT
Green: I < 640mA
OUT
Orange: I 640...900mA
OUT
Red: I > 900mA (overload)
OUT
5. Internal temperature
Green: Temperature is 0...75°C
Red: Temperature is out of this range
6. KNX reset
Red: Restart of the KNX bus line is running
7. Programming
Red: Programming mode active
LED INDICATION
SPECIFICATIONS

page 3
PS-S.640.30.1
+
-
KNX bus
N
L
AUX KNX
L N
+
-
AUX
PASSPORT
МГРЛ-27.12.1931-008.01 ПС
INSTALLATION
Attaching to DIN rail
Removing from DIN rail
WIRING DIAGRAMS

SAFETY INSTRUCTIONS
ATTENTION! Installation and connection of the device to the mains must only be carried out by
qualified personnel! There is a risk of electric shock! Be sure to turn off the power before installing or
removing the device! Even when the device is turned off, the output terminals can be live! Do not
connect to the outputs a load that exceeds the recommended values! The design of the device meets
the requirements of electrical safety according to GOST 12.2.007.0-75.
SETTING INSTRUCTIONS
The device is set up in accordance with the instruction manual. (The full manual and application program can be
downloaded at https://module-electronic.ru/documents or by scanning the QR code at the bottom of the
document).
TRANSPORTATION, STORAGE AND DISPOSAL
The conditions for the transportation of devices must comply with conditions 5 of GOST 15150-69.
Storage of devices in packaging at the warehouses of the manufacturer and consumer must comply with storage
conditions 1 in accordance with GOST 15150-69. Aer transportation or storage at low temperatures, it is
necessary to withstand the device at room temperature for at least 2 hours before turning it on. Do not dispose
of the device with household waste.
WARRANTY
Warranty period - 12 months from the date of sale to the consumer. The manufacturer is not liable and does not
indemnify for damage caused by the fault of the consumer in case of non-compliance with the conditions of
transportation, storage, installation and operation, as well as in case of violation of the seal when trying to repair
the device yourself.
All the necessary information on the warranty can be obtained by the consumer by calling Module Electronics or
on the website: www.module-electronic.ru.
Serial number
page 4
Made in Russia
Name, address of the trading organization
Date of sale
Seller Signature
seller's stamp
User Manual
module-electronic.ru