modway EEI-2772 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 4
EEI –2772/2653 OFFICE CHAIR
Hardware:
Component:
Thank you for purchasing the MODWAY OFFICE CHAIR！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the office chair, we recommend that it is assembled by two adults, on a carpeted
or padded area, in the room that it is intended for. Approximate assembly time: 15 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
1
2
3
Bolt M8*25mm
Bolt M8*30mm
Flat Washer 8*17mm
4
H Castors X5
H
E
BC
A
B Right Armrest
F Cylinder X1
A Chair Back X1
E Control Mechanism
X3
X8
X7
Allen Wrench X1
C Left Armrest
G Chair Base
X1
X1
X1
X1
D Chair Seat X1
D
F
H
H
H
HG

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 4
EEI –2772/2653 OFFICE CHAIR
STEP 1:
Please put Chair Base (G) upside down on a carpeted or padded surface. Insert 1pc of Castor (H) into the Chair Base
(G) as shown by hand. Repeat the same steps for the remaining 4pcs of Castor (H).
STEP 2:
Flip the assembled Chair Base (G) with Castors (H) on the floor. Insert the bottom end of Cylinder (F) into the
assembled Chair Base (G) as shown.
H
H
H
H
H
G
G
F

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 4
EEI –2772/2653 OFFICE CHAIR
STEP 4:
Please put the Chair Back (A) upside down on a carton.
Attach Control Mechanism (E) into the bottom of Chair Back (A) by using 1 pieces of Bolt (1) and 2 pieces of Bolt(2)
with 3 pieces of Flat Washer (2) as shown.
Use Allen Wrench (4) to tighten all Bolts (1) and Bolts (2) clockwise until secure.
1. 2. 3. 4.
1x1pcs 2x2pcs 3x3pcs 4x1pcs Hardware & Tool required
STEP 3:
Please put the Chair Seat (D) upside down on a carton.
Attach Chair Right Armrest (B) and Left Armrest (C) into the bottom of Chair Seat (D) by using 4 pieces of Bolt (2)
as shown.
Use Allen Wrench (4) to tighten all Bolts (2) clockwise until secure.
2
2
2
2
4
B
C
2x4pcs 4x1pcs
Hardware & Tool required
A
E
2
21
3
3
4
D
3
2. 4.

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 4
EEI –2772/2653 OFFICE CHAIR
Hardware & Tool required
STEP 6:
Carefully turn over the assembled Chair Back (A), Right Armrest (B), Left Armrest (C),Chair Seat (D) and Control
Mechanism (E). Please insert the bottom holes of Control Mechanism (E) into the top end of assembled Cylinder (F)
as shown. Sit on Chair Seat (D) to fully tighten the office chair.
STEP 5:
Please put the assembled Chair Seat (D) upside down on a carton.
Attach Control Mechanism (E) into the bottom of Chair Seat (D) by using 2 pieces of Bolt (1) and 2 pieces of Bolt (2)
with 4 pieces of Flat Washer (2) as shown.
Use Allen Wrench (4) to tighten all Bolts (1) and Bolts(2) clockwise until secure.
Assembly is complete. The office chair is ready to be enjoyed now!
1. 2. 3. 4.
1x2pcs 2x2pcs 3x4pcs 4x1pcs
2
2
4
3
3
3
3
1
1
E
A
D
B
C