modway MOD-5492 User manual

A
B
JCBB BOLT M8 X 16MM
M4 ALLEN KEY (BALL SHAPE)LONG
C
D
F
G
SPRING WASHER 1/4"
FLAT WASHER 1/4''
MOD-5492/ MOD-5493 / MOD-5494 / MOD-5495
Thank you for purchasing the MODWAY BED !
Before you start,here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the bed, we recommed that it is assembled by two adults,on a carpeted or
padded area, in the room that it is intended for.Approx assembly time:30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled.Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
5.Assemble all components loosely until advised to tighten.Depending on use, it may be necessary to tighten
the components from time to time,so please save the tools that has been provided.
6.Please keep all fitting out of reach of children.
Hardware for Headboard
Hardware for Side rails and Footboard
Component :
Customer Service 908-368-1025 Page 1/4
x8
x1
x1
x2
x5
x2
CSK SCREW M4 X 32MM x28
E
3
M5 ALLEN KEY
JCBC BOLT M6 X 35MM
2
1
64
5
1- HEADBOARD 6- LEG SUPPORT
2- FOOTBOARD
3- SIDE RAILS
4- CENTER RAIL
5- RAILS
x1
x1
x2
x1
x14
x3
H
x3
JCBC BOLT M6 X 60MM
www.modway.com

Place
Place
A x 4 E x 2
Hardware & Tool required
STEP 1 :
Place SIDE RAILS (3) and FOOTBOARD (2) on a carpeted or padded area as shown. Attach FOOTBOARD (2) with SIDE RAILS
(3) together by inserting JCBB BOLT M8 x 16MM (A).Tighten up the bolts with M5 Allen Key (B). Place SPRING WASHER 1
4" (E)
and FLAT WASHER 1
4" (F) into JCBC BOLT M6 x 35mm (C). After that, inserting JCBC BOLT M6 x 35mm (C) at bottom side of
SIDERAILS (3) and FOOTBOARD (2). Tighten up the bolts with M4 Allen Key (BALL SHAPE) LONG (H).
STEP 2 :
Hardware & Tool required
Page 2/4
Customer Service 908-368-1025
4x 2x
F x 2 B x 1 H x 1
C x 2
4x
A
BD
C
E
G
Attach HEADBOARD (1) with SIDE RAILS (3) together by inserting JCBB BOLT M8 x 16MM (A).Tighten up the bolts with M5 Allen
Key (B).
A x 4 B x 1
A
B
1
2
3
MOD-5492/ MOD-5493 / MOD-5494 / MOD-5495
www.modway.com

Place
Place
D x 3
Hardware & Tool required
STEP 3 :
STEP 4 :
Page 3/4
Customer Service 908-368-1025
Place the balance of Rails (5) equally on the Center Rail (4). Then screw it up with CSK Screw M4 x 32mm (G) on both side of
Rail (5).
Hardware & Tool required
G x 28
3x
E x 3
28x
D
G
C
H x 1
F
4
5
5
6
Place the CENTER RAILS (4) on Leg Supports (6). Parallel place three RAILS (5) vertically on the Center Rail (4) as shown with the
center holes lined up. Attach them together by inserting JCBC BOLT M6 x 60mm (D) and Spring Washer 1
4'' (E). Tighten it up with M4
Allen Key (Ball Shape) Long (H).
MOD-5492/ MOD-5493 / MOD-5494 / MOD-5495
www.modway.com

STEP 5 :
Page 4/4
Customer Service 908-368-1025
Remark: Do not sit or lie on
platform without the
mattress
Assembly is completed.The bed is ready to enjoy now !
MOD-5492/ MOD-5493 / MOD-5494 / MOD-5495
www.modway.com