modway EEI-2589 User manual

EEI-2589/2595 LEFT/RIGHT ARM LOVESEAT
Thank you for purchasing the MODWAY LEFT/RIGHT ARM LOVESEAT!
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by step instructions.
2. Owing to the size and weight of the sofa, we recommend that it is assembled by two adults on a carpeted or
padded area, in the room that it is intended for. Approximate time: 30 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
component from time to time, so please save the tools that have been provided.
6. Please keep all pieces out of reach of children.
Components:
1. Loveseat Frame x1 2. Leg x4 3. Loveseat Seat Cushion x2 4. Loveseat Back Cushion x2
Customer Service 908-368-1025 I www.modwayfurniture.com Page 1 of 2
EEI-2589 LEFT ARM LOVESEAT
EEI-2595 RIGHT ARM LOVESEAT

EEI-2589/2595 LEFT/RIGHT ARM LOVESEAT
STEP 1:
Please put the Loveseat Frame (1) without Seat Cushion (3), Back Cushion (4) upside down on a carpeted or
padded area by two adults to make fully visible the round metal plate on each corner and middle.Open the Zipper
on the bottom of Loveseat Frame (1) as shown, take out the packages of 4 pieces Leg (2), then close the Zipper
on the bottom of Loveseat Frame (1). Take off the Black Protection Cover on the 4 piece Leg (2) .
Insert 1 piece of Leg (2) into the hole on the round metal plate at the corners of the Loveseat (1). as shown.
Use Hands to tighten the Leg (2) clockwise until secure.Repeat the same steps for the remaining Legs (2).
STEP 2:
Carefully turn over the Loveseat Frame (1). Put Seat Cushion (3) and Back Cushion (4) to the assembled
Loveseat (1) as shown.
Assembly is complete.The Loveseat is ready to enjoy now!
Customer Service 908-368-1025 I www.modwayfurniture.com Page 2 of 2
Black Protection Cover
x 4PCS
Legs inside

EEI-2611/2612 LEFT/RIGHT BUMPER CHAISE
Thank you for purchasing the MODWAY LEFT/RIGHT BUMPER CHAISE!
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by step instructions.
2. Owing to the size and weight of the sofa, we recommend that it is assembled by two adults on a carpeted or
padded area, in the room that it is intended for. Approximate time: 30 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
component from time to time, so please save the tools that have been provided.
6. Please keep all pieces out of reach of children.
Components:
1. Chaise Frame x1 2. Seat Cushion x1 3. Back Cushion x1
4. Side Cushion I x1 5. Side Cushion II x1 6. Leg x 5
Customer Service 908-368-1025 I www.modwayfurniture.com Page 1 of 2
EEI-2611 LEFT BUMPER CHAISE
EEI-2612 RIGHT BUMPER CHAISE

EEI-2611/2612 LEFT/RIGHT BUMPER CHAISE
STEP 1:
Please put the Bumper Chaise Frame (1) without Seat Cushion (2), Back Cushion (3) and Side Cushion (4&5)
upside down on a carpeted or padded area by two adults to make fully visible the round metal plate on each corner
and middle.Open the Zipper on the bottom of Bumper Chaise Frame (1) as shown, take out the packages of
5 pieces Leg (6), then close the Zipper on the bottom of Bumper Chaise Frame (1).
Take off the Black Protection Cover on the 5 piece Leg (6).
Insert 1 piece of Leg (6) labeled "Middle Leg" into the middle hole on the round metal plate at the middle of
Bumper Chaise (1). Insert 1 piece of Leg (6) into the hole on the round metal plate at the corners of the
Bumper Chaise (1). Repeat the same steps for the remaining Legs (6).
X5 PCS
STEP 2:
Carefully turn over the Bumper Chaise Frame (1). Put Seat Cushion (2), Back Cushion (3)
and Side Cushion (4&5) to the assembled Bumper Chaise as shown.
Assembly is complete.The Bumper Chaise is ready to enjoy now!
Customer Service 908-368-1025 I www.modwayfurniture.com Page 2 of 2
Black Protection Cover
x 5PCS
Legs inside