Moneual MBOT 500 User manual

Ver 1.0
User manual
MBOT 500

2
Contents
01
Before use Important Instructions
03
Package content
05
Product description
06
Installation
instructions
Charging station
07
Installing the remote control
08
Charging the device
09
Product
operation
Instructions before operation
10
Remote control & functions
11
12
Start cleaning
13
End cleaning
Care and
maintenance
Customer
service
Cleaning the dust bin
14
Cleaning the dust lter
15
16
Cleaning the sensors and wheels
17
Cleaning the main brush
Cleaning the side brushes
18
18
Storage/Battery change
19
Cleaning the charging contact
20
Troubleshooting
21
Technical specications
Thank you for deciding to purchase this MONEUAL
MBOT robot vacuum cleaner. Before using the product,
please read this user manual carefully and keep it for
future reference.
Depending on the model, some content of this user
manual may vary from the actual product. The
contents of this manual are subject to change without
notice.
Copyright
All rights reserved.
Published on 1 February 2019
MONEUAL is a brand/a registered trademark of MTG
GmbH in Europe and/or other countries.
The publication is protected by copyright and all
rights are reserved. No part may be copied or
communicated in any form without prior written
approval from MONEUAL.
Depending on your model and type of device, some
content in this manual may vary.
MTG GmbH takes no responsibility for any technical
or text-related errors, omissions or any incidental or
consequential damages or malfunctions of the
equipment resulting from failure to comply with the
safety and user instructions.
MTG GmbH takes no responsibility for damage
caused by not using the device according to the
instructions.

3
Important Instructions
02
etoNnoituaCgninraW
You may be killed or seriously injured
if you do not follow this instruction.
Warning: Please read and follow the instructions in the manual to ensure your safety and the safe use of your
robot cleaner. In case of disregard, there is no liability for personal injury and property damage. Warranty is valid
only if you follow the instructions.
Keep away from abysses and do not use on elevated objects such as tables, etc.. To prevent your device from falling,
place an obstacle in front of the abyss.
When using the device, ensure that you are within reach of the device, so that you can intervene and relocate
the device.
This appliance can be used by children aged 8 years and above, same as persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of
this appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
WARNING: For the purposes of recharging the battery, only use the detachable supply unit provided with this appliance.The battery
must be removed from the appliance before it is scrapped. The appliance must be disconnected from the supplymains when
removing the battery. The battery must be disposed of in accordance with local regulations.
If the dust bin is full, the cleaning performance will be reduced.
Empty the dust bin after each use (see page 14).
Please clean the cli sensors and wheels regulary (see page 16).
Be careful not to break the robot cleaner when you pull it out of the box.
Install the side brushes.
The device must be fully charged before rst use.
Remove any obstacles on the oor before you start cleaning mode.
The robot cleaner can not climb thresholds higher than 10mm.
After charging is complete, keep the robot cleaner docked to the charging station.
The robot will turn o automatically.
Install the charging station in a location that can be easily accessed by the robot cleaner (1m distance to each side).
You may be injured or your appliance
may be damaged if you do not follow
this instruction.
Important information, denitions,
general rules and notes are explained.

Important Instructions
02
4
Only use the original adapter, battery and the original charging station to prevent damage to the device as well
as electric shocks, surges and/or re.
If damage occurs to the device or accessories, discontinue use of the robot and contact customer service. Never
perform any repairs yourself.
Never operate the device and any accessories with wet hands.
Areas of use The device can be used on the following surfaces:
Wooden oors Stone oors Short and medium pile
carpets
Plastic oors
Before cleaning, remove
any cables and loose
objects to avoid the device
malfunctioning.
If the device is not used for
several weeks, unplug the
power cable to protect the
battery.
Do not use the device in
damp, ammable,
explosive or corrosive
environments.
Warning!

03 Package content
MBOT500 robot vacuum cleaner
- Pre-assembled main brush and side brushes
- Pre-assembled dust bin and lter
Charging station Adapter Multi-functional
remote control
Replacement set of
side brushes
Cleaning brush
for cleaning the main brush
Screwdriver and
replacement screws -
for loosening/tightening
the side brushes
Replacement lter set Warranty booklet
and Quick Guide
5

04
②
②
①
①
③
④
④
⑤
⑥
⑦
⑥
⑦⑧⑨
⑤
③
②Dust Bin
③Dust bin button
①Upper cover
④Operating button
⑤Impact strip
⑥Signal window for obstacle sensors
⑦Side brushes
①Charging contact
②Floor sensor / fall sensor
③Front wheel/castor
④Side brushes
⑤Main brush
⑥Drive wheel
⑦Cover for main brushes
⑧Nameplate
⑨Battery cover
6
Product description

05 Charging station
When using the charging station,
remember that there should be a min.
clearance of 3m at the front and 1m at the sides.
Adaptor plug
Charging terminal
Plug in the mains adaptor. If there is a power connection,
the green LED on the top of the charging station is lit.
Make sure that
there are no loose
objects around the
charging station.
Do not place the charging
station next to a down stairway.
1m 1m
3m
Warning!
7

06 Remote control
Use the locking lever to remove the battery cover.
Install the AAA batteries supplied in the correct
direction and replace the cover.
Point the remote control at the robot and press
Start/Pause once to test the robot’s reaction.
If the robot beeps, a connection has been made.
The remote control’s range is 7 metres.
8

07 Charging the device
Hold the device with both hands and place it
on the charging station. Make sure that the
robot's contact is on the charging station.
The device beeps after a second and the LED
ring lights up as soon as contact is made.
Connect the robot to the remote control
(see page 8).
When the device’s LED ring is lit, the robot
can automatically be found by pressing the
home button on the charging station.
If the battery is completely discharged, this charge will last for around 4-5 hours.
Warning!
LED status Meaning
ashing red Battery empty (place on the charging station manually)
red Error message (see page 20)
ashing green low battery -> nd charging station
pulsing green charged
O Battery fully charged/o
9

08
Make sure that the robot vacuum cleaner is not damaged when it is removed from its packaging.
Please consider the following points before using the robot vacuum cleaner.
1
Instructions before operation
The device must be fully charged before being used for the rst time.
See page 9 for further details about charging.
2
Keep the oor free from loose objects.
Before cleaning, please remove any fragile objects or very light or fringed fabrics from the oor,
which could aect the movement of the device. Place long rug fringes under the rug.
3
Emptying the dust bin.
The suction capacity is limited when the dust bin is full.
See page 14 for further details about emptying.
4
Cleaning the sensors.
If the sensors (crash sensors, signal window) or wheel are very dirty, this may cause an error or crash.
See page 16 for further details about cleaning.
5
Help children and the elderly.
Inform children and the elderly about using the robot so that they are not frightened.
6
7
The device cannot pass over sections over 15mm high.
8
Keep the device away from precipices or falling edges.
When objects are present (e.g. shoes on the stairs), an error may be detected and the device may fail.
The charging station must be at least 5 metres from falling edges. Never use the device on tables,
stools or stairs. The crash sensors must be cleaned regularly.
Unplug the charging station when it is not in use.
If the device is not to be used for a long period of time, please unplug the charging station.
This protects the battery.
9
10

11
09
Set current time:
1. - Press button
2. Set the time with and
3. Switch between minutes and
hours using and
4. With - Conrm button
5. Robot beeps once
Set cleaning plan:
1. - Press button
2. Set the time with and
3. Switch between minutes and
hours using and
4. With - Conrm button
5. Robot beeps once
Disable:
1. - Press button for 2 seconds
2. Robot beeps twice
Suction capacity
Setting:
Step 1: 1x press
Quiet mode
longest operation
Device beeps once
Step 2: 2x presses
Normal mode
Device beeps twice
Step 3: 3x presses
Turbo mode
strongest suction
Device beeps 3 times
Battery low
Change, see page 8.
Start/Stop
- Turn robot on
- Start cleaning
- End cleaning
- time setting -> conrm
Direction keys
- Set time
- Control the robot manually
- at , the device only moves
backwards gradually
Edge cleaning
- precise cleaning along the walls
- moves to an object and then moves left
30-Min room cleaning
- ideal for small, closed rooms
- after 30 mins, the device stops cleaning
and searches for the charging station.
Charging
- the robot searches for the charging station
Cleaning plan
- Set start time for the next
automatic cleaning
- Setting: see above
Setting the time
- Current time
- Setting: see above
Time
SCHEDULED TIME
Remote control & functions
If the robot no longer responds to the remote control, check the status of the batteries and
connect both devices again.
To connect the device, press and hold and the robot switches on after 3 seconds. The
robot beeps 3 times if the connection is successful.

12
10
1. Turning the device on and o
2. Start cleaning
press!
3 seconds
press!
or
To switch the device on, hold the button for 2 seconds until the device beeps.
As a result, the LED lights up green. The device is in standby mode.t
To switch the device o, hold the button in standby mode for 3 seconds until the device beeps.
The green LED then goes out.
The device operates chaotically, not line-by-line. An area of up to 150 m² can be cleaned with one charge.
Start cleaning

13
11
or
When the battery is low, the robot
automatically searches for its charging
station.
It performs certain movements repeatedly
until it nds the charging station’s signal.
Its status can be recognised by the ashing
LED ring and the deactivated suction motor.
AUTO
If the robot is docked correctly, it beeps once
and the charging process begins.
The LED ashes green.
During operation, if you press button
on the robot or the Start/Stop button
on the remote control, the cleaning
programme ends.
The robot make take a long time to or not be able to nd its charging station.
This often means it is in a complex environment or the battery is empty.
End cleaning

14
12
The transparent part of the dust bin can be separated from the upper section
and rinsed in cold water. Please dry thoroughly before using again.
Press!
Press the dust bin
button to release.
The dust bin springs up by
a few millimetres so it can
be easily removed.
Flip the lid of the dust bin
open and empty the bin.
Use the cleaning brush supplied to
remove any dirt from the dust bin and the lter.
Pull the dust bin up
from the housing.
②① ③
Cleaning the dust bin
④⑤

13
15
Remove the lter cover by
pulling the top of the
dust bin upward.
Remove any dirt from the
lter cover using the
cleaning brush supplied.
The lter cover as well as
the ne particle lter
and the lter sponge
can be cleaned in cold water.
To speed up the
drying process,
the lter parts
can be blown
with cold air.
Replace the lter parts
and press down
on the lter cover.
Clip the dust bin
rmly together.
Return the dust bin
to the device.
Cleaning the dust lter

14
16
Clean the three oor sensors with
the cleaning brush supplied or
with a cotton bud.
- If the sensors are very dirty,
you can use a moistened
cotton bud.
- Do not use too much moisture.
- Never use alcohol or thinner.
Clean the front wheel and the drive
wheels with the cleaning brush supplied.
- If the front wheel is stuck, you can pull it
upwards to remove any internal dirt.
- Remove any hair and dirt collected.
Cleaning the sensors and wheels

15
17
Press the brush cover’s release
lever in and pull the brush upward.
Lift the main brush on the left
side to remove it from its mount.
First insert the main brush with the
square on the right side.
Replace the cover correctly.
Remove any hair collected using the ne blade
on the cleaning brush supplied.
Coarse dirt can be removed using the comb of the
cleaning brush.
Cleaning the main brush

18
16
17
Remove the screws from the side brushes with
the screwdriver provided and pull
the side brushes upwards.
Remove any hair and dirt collected and replace
the side brushes and tighten them.
Right and left do not matter.
if you are not using the robot for a long period
of time, please remove the battery to extend its life.
Remove the battery cover using the
screwdriver supplied.
Remove the battery by disconnecting the cable.
Make sure that the cable does not slip
into the housing.
Cleaning the side brushes
Storage/Battery change

18
19
If the device experiences problems when docking
on the charging station, please check the charging
contact on the bottom of the robot. If this is very
dirty, no contact can be made with the charging
station.
To guarantee full functionality,
please clean the impact strip and
the signal window regularly.
Impact strip
Signal window for obstacle sensors
Cleaning the charging contact

20
19
- The robot vacuum cleaner gives out a combination of LED colours and beeps to inform you
of the issue/error concerned.
- First try solving the issue using the suggestions below.
- If the proposed solutions are unsuccessful, please contact customer services.
- The error message beeps 10 times 3 seconds apart.
Cause
LED red
1x beep
LED red
2x beep
LED red
3x beep
LED red
4x beep
LED red
5x beep
LED ashes red
1x beep
LED ashes red
2x beep
LED ashes red
3x beep
LED ashes red
4x beep
LED ashes red
5x beep
LED ashes red
6x beep
Drive wheel (left/right) is not working or is overloaded.
Solution
Solution
Cause
Cause
Solution
Solution
Cause
Cause
Solution
Solution
Cause
Cause
Solution
Solution
Cause
Cause
Solution
Solution
Cause
Cause
Solution
Check if the wheels are clogged by dirt or hair.
Side brush (left/right) is not working or is overloaded.
Check if the side brushes are clogged by dirt, hair or the cable.
Main brush is not working or is overloaded.
Check if the main brush are clogged by dirt or hair or the cable.
Impact strip stuck or impact sensor defective.
Check whether the impact strip exes normally or is stuck.
Front wheel/castor not moving.
Check whether the front wheel can rotate freely.
Floor/crash sensors defective or dirty.
Check whether the device is already on the oor or if the oor sensors are dirty.
Battery level too low.
Place the device in the charging station manually.
System error.
Place the device in a dierent location and try again.
The vacuum motor is not working or the device has no suction.
Clean the main brush and try again.
Obstacle sensors are blind.
Check whether the impact strip’s signal window is very dirty.
The dust bin is not inserted.
Insert the dust bin correctly.
Troubleshooting