MONI LOG EnDal smart User manual

EnDaL smart
Edition 11/2015
INSTRUCTION MANUAL
for
EnDaL smart
(Transport data logger)

EnDaL smart PRODUCT CERTIFICATION
- 1 -
P R O D U C T C E R T I F I C A T I O N
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Modifications not expressly approved by this company could void the user's
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
This device complies with Industry Canada’s RSS-310. Operation is subject to the
condition that this device must not cause harmful interference and must accept any
interference, including interference that may cause undesired operation of the
device.
Cet appareil est conforme à la norme RSS-310 d'Industrie Canada. L'opération est
soumise à la condition que ce dispositif ne doit pas causer d'interférence nuisible et
doit accepter toute interférence, y compris les interférences qui peuvent entraîner
un mauvais fonctionnement de l'appareil.
This EXPERTISE is issued in accordance with the Directive 1999/5/EC of the
European Parliament and Council on radio equipment and telecommunications
terminal equipment and mutual recognition of their conformity dated 9th March
1999 and is only valid in conjunction with following annex: -1- (2 pages)
This device has been designed to operate with the antennas listed below (see Technical Parameter). Antennas not
included in this list are strictly prohibited for use with this device. The required antenna impedance is 50
ohms.To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful
communication.
Cet appareil a été conçu pour fonctionner avec les antennes énumérées ci-dessous (voir 2. Paramètres techniques). Les
antennes n’étant pas énumérées dans cette liste sont strictement interdites pour une utilisation en combinaison
avec cet appareil. L'impédance de l’antenne requise est de 50 ohms. Afin de réduire les interférences radio
potentielles pour les autres utilisateurs, le type d'antenne doit être choisi afin que la puissance isotrope
équivalente (e.i.r.p.) ne soit pas supérieure à celle permise pour réaliser une communication stable.

TABLE OF CONTENTS EnDaL smart
- 2 -
T A B L E O F C ON T E N T S
PRODUCT CERTIFICATION.................................................................................. 1
TABLE OF CONTENTS ........................................................................................ 2
1. INTRODUCTION ...................................................................................... 4
1.1 SCOPE OF DELIVERY.................................................................................................... 4
1.2 FUNKTIONALITY......................................................................................................... 5
1.3 ENVIRONMENTAL AND SAFETY INSTRUCTIONS................................................................... 7
2. TECHNICAL PARAMETERS......................................................................... 8
3. DEVICE DESCRIPTION OF ENDAL SMART.................................. 10
3.1 DEVICE SETUP /DEVICE VIEW ...................................................................................... 10
3.2 OPERATION OF THE ®ENDALSMART ............................................................... 11
3.3 MEANING OF THE LED STATUSES ................................................................................. 12
3.4 DEVICE RUNTIME AND BATTERY CHANGE ....................................................................... 15
3.5 MOUNTING INFORMATION........................................................................................ 17
4. PC SOFTWARE –ANALYZER ................................................... 18
4.1 INSTALLATION ......................................................................................................... 18
4.1.1 General software installation ....................................................................................... 18
4.1.2 USB driver ................................................................................................................ 19
4.2 GENERAL USE OF THE PC SOFTWARE ........................................................................... 20
4.2.1 Establishing the device connection................................................................................ 20
4.2.2 File area ................................................................................................................... 21
4.2.3 Message window (Log) ............................................................................................... 21
4.2.4 View of the measurement data ..................................................................................... 22
4.3 ENDAL SMART….................................................................................... 24
4 . 3 . 1 R e a d i n g o u t s t a t u s , c o n f i g u r a t i o n a n d m e a s u r e m e n t d a t a ..................... 24
4.3.2 Overview window...................................................................................................... 25
4.3.3 Status and thresholds.................................................................................................. 26
4.3.4 System events ............................................................................................................ 29
4.3.5 Logging periods......................................................................................................... 30
4.3.6 Synchronous data graphs............................................................................................ 31
4.3.7 Inclination curves ....................................................................................................... 33

EnDaL smart TABLE OF CONTENTS
- 3 -
4.3.8 Alarm events.............................................................................................................. 34
4.3.9 Shock events and shock curves..................................................................................... 35
4.3.10 GPS position determination.......................................................................................... 38
4.3.11 Configuration of the EnDaL smart ................................................................ 42

INTRODUCTION EnDaL smart
- 4 -
1. I N T R OD U C T I O N
1.1 S C O P E O F D E L I V E R Y
Thank you
for having chosen the EnDaL smart.
Scope of delivery1(standard):
EnDaL smart, incl. 2 x R14, alkaline or lithium batteries according to your
requirement
Installation CD
Configuration software „ Analyzer“ with integrated software help
Driver for USB interface
Operating instruction in electronic form (PDF)
Hard copy of the operating instruction
USB 2.0 interface cable (type A ↔type Mini AB)
GPS antenna
In order to be able to further optimise our products for the respective applications, we are always
open to suggestions and change requests on your part.
1) The scope of delivery can deviate from the standard due to special contract agreements!

EnDaL smart INTRODUCTION
- 5 -
1.2 F U N K T I O N A L I T Y
The EnDaL smart is a universal data logger. Developed for long-term measurement
applications, it is perfectly suited for the monitoring of transport goods and critical environments.
The integrated sensor system for the detection of shock events and for the measurement of
temperature, humidity, air pressure, and inclination enables a wide range of different
measurement applications.
Configured alarm thresholds ensure the reliable detection of exceedances of limit values. The
possibility of position determination of the EnDaL smart at events and time-
controlled allows both the verification of the transport route and a precise localisation of critical
transport processes.
The up to 15,000 recorded position data sets,
including speed and direction, can be
imported afterwards into Google Earth or
similar software and be evaluated.
The compact and network-independent design enables
simple fixing on or in transport goods and transport devices.
The case of the device protects against dust and splash water
(degree of protection IP 65) and thus is also suitable for the
exterior use. Thanks to this, the EnDaL smart can be
universally used as an almost invisible goods companion in the
international transport of goods, in storage rooms, at reloading
points and during transport by rail, by roads as well as by water
and by air.
The power supply is realised by customary, exchangeable alkaline or lithium batteries. Thanks
to very low current consumption and associated very long, maintenance-free operating time, the
EnDaL smart is perfectly suited for self-sufficient long-term applications. Energy-
optimised operating settings render possible a self-sufficient operational time of up to one year
under rough ambient conditions.

INTRODUCTION EnDaL smart
- 6 -
The licence-free configuration software Analyzer enables a simple and intuitive
configuration of the devices. It offers a comprehensive adjustment of the device functions to your
application-specific requirements. Besides the detailed evaluation of the device data in measured
value tables and graphs, the programme also provides export functions for external applications
(e.g. Microsoft Excel).

EnDaL smart INTRODUCTION
- 7 -
1.3 E N V I R O N M E N T A L A ND S A F E T Y INS T R U C T I O N S
Environment & disposal
The EnDaL smart contains, excluding the internal batteries, no corrosive or
environmentally damaging substances.
Used batteries must be immediately removed from the device and be disposed of in an
environmentally friendly manner, according to the applicable legislation. Lithium batteries are
hazardous waste.
Battery operation
The power supply is ensured in the EnDaL smart by means of 2 exchangeable
alkaline or lithium batteries (type C|R14). These can be bought in specialized stores according to
the specification stated in the instruction manual.
When lithium batteries are used on transport, the EnDaL smart must be labelled as
hazardous material of class 9, according to the Worldwide UN classification. The transport
conditions resulting due to this must be taken into account!
Please take into account that when using alternative battery types the functionality of the device
cannot be guaranteed in the entire specified temperature range from -40 to 85 °C.
ATTENTION!
Use only intrinsically safe batteries.
In case of non-compliance with the national regulations/laws applicable in the handling of
lithium batteries, any liability and warranty claim becomes void!
Decommissioning
In case of decommissioning the devices must be properly switched off and all batteries must be
removed from the cases and be disposed of in an environmentally friendly manner.

TECHNICAL PARAMETERS EnDaL smart
- 8 -
2. T E C H N I C AL P A R A M E T E R S
Case
Case material
Aluminium, powder-coated
Degree of protection
IP67
Weight
0.8 kg (standard version without batteries)
38g (each magnetic base, 3 pieces per module optional)
Dimensions (H/W/D)
35 x 140 x 100 mm³ (standard version)
Ø25mm x 15mm (small magnetic base)
Mounting type
surface mounting (screw fixing recommended), alternatively magnetic base
mounting (upon request)
Application conditions
Operating and storage
conditions
-20°C to +70°C with alkaline batteries
-40°C to +85°C with Lithium batteries
Data memory, time
Data retention
minimum 10 years (independent of battery condition)
Memory type/size
32 MB flash parameter and data memory
System time
Date / Time as UTC time supported independently from the power
supply by an internal battery,
exchange at SMT & HYBRID after 6 years needed
Voltage supply
Internal
2 batteries of type C or R14 exchangeable
oalkaline batteries (2 x 1.5 V; 8000 mAh)
oLithium batteries exchangeable (2 x 3.6 V; 8500 mAh)
Service life: at least 1 year (in case of synchronous interval of 10 min,
all options active)
External interfaces
USB
USB 2.0 Client (Mini-USB AB)
Indicating and operating elements
LED
1 green active LED
1 red alarm LED
1 red-green battery LED (bicoloured)
Key button
1 On/Off key