Monitech ML050CT509 User manual

M20A03-CT509
1
M L 0 5 0 C T 5 0 9 INSTALL GUIDE
LCD upgrade kit
FOR YOUR IKEGAMI PM-509

M20A03-CT509
2
IMPORTANT:
WARRANTY
Before using any MONITECH product please carefully
review this Manual as well as any additional
documentation provided with your shipment.
Attempting any of the following will void product warranty:
•unauthorized repairs or parts replacement
•inappropriate use or placement: exposing product to
liquids, harmful gases, electrical shock, physical
shock, temperatures beyond the range of -4°F to
140°F
(-20°C to 60°C)
•use of electrical voltage other than 12V 4.16A
(power supply and AC cable provided)
•Removal or modification of serial, product, or
warranty labels.
WARNING
ELECTRICAL HAZARD
DO NOT OPEN
TO AVOID ELECTRICAL SHOCK DO NOT
OPEN PRODUCT CASING. UNAUTHORIZED
REPAIRS OR PARTS REPLACEMENT ARE
PROHIBITED AND WILL VOID PRODUCT
WARRANTY. PLEASE RETURN TO
MONITECH FOR REPAIRS.

M20A03-CT509
3
REMOVALE:
Step #1) Turn off turn off power, Unplug the power cord.
Step #2) Remove the Cover, Button Plate & Bezel by unfastening the
screws.
Step #3) Remove the CRT out of the chassis by unfastening the 4 mounting
nuts that hold the CRT in place. Keep the nuts because you are going to
need them to put your Monitech LCD Upgrade back into your machine.
Nuts that are to
be unfastened, to
remove the CRT
from the chassis
CRT
Cover
Button
Plate

M20A03-CT509
4
Step #4) Remove CRT out of chassis by, first grounding out CRT by placing
a flathead screwdriver underneath the anode lead, and make sure the
screwdriver is touching the metal in the middle of the anode lead and the
other end is touching the ear of the CRT and have another screw driver
cross with your flat head screw driver. This is for safe removal. Remove
anode lead by pressing one side of the screwdriver to the metal in the middle
of the anode lead & take it out from the same side you were pressing.
Step #4) Remove the Neck Board from the CRT it is located at the back of
the monitor. Remove the Yoke from the Board in the chassis. Remove any
other connectors to the boards on the chassis such as Degus Cable and
unscrew 4 screws holding ears of CRT to chassis, so that that the CRT can
be remove fully out of the chassis. Remove all other remaining circuitry in the
chassis. Remove screws that hold the boards in place and take out boards
and then the other cables.
Anode
Lead
Flathead Screw
Driver to middle of
anode and to ear
Cross the
screwdrivers
Unplug Neck
board
Back of CRT
Unplug from this
connection this is
the Yoke

M20A03-CT509
5
ASSEMBLE:
Step #5) Now you have an open chassis. Place Monitech’s LCD Upgrade on
to the chassis by using the same holes that held your CRT. Use the nuts
previously removed to hold the LCD in place. Screw in the User Controls.
Place the
LCD Bezel
this this
use the
nuts if
possible
Take the
board out,
by
removing
one side of
the chassis
Take the back
off the chassis
Take the board off the
removed chassis
Reattach the
previously
removed
chassis to the
full chassis

M20A03-CT509
6
Step #6) Remove the board off the back cover by snipping the metal wires.
Remove the IN BNC and replace it with our BNC (MAV051). Cut the wire
attaching the power to the boards. Crimp and fasten MAP204 to power
wires.
Step #7) Connect your MAP304 into MAP307. Put the Jack of MAP307 into
Monitor. Then connect your BNC to the Board. Connect the User Controls to
the board. Follow Picture.
MAP307
MAP304
Cut over here
with snips
Strip your black and white wires. With butt connector connect
the white wire to red wire of MAP304. With the black wire attach
it to the blue wire of the MAP304. Attach grounds together.
Unscrew In BNC and replace
it with our BNC (MAV051)
Plug in the
jack from
MAP307 into
the monitor
Connect User Controls into board with ribbon wire.
Connect the BNC to
the Board

M20A03-CT509
7
INSTALLATION:
Step #8) Plug in the power cord. Plug BNC to a DVD player using our
test cable. Press power button on user controls. Check if monitor is
working. If you want to double check, turn power off then unplug BNC
connector and plug MAV050 into board shown in picture below. Connect
MAV003 to your computer and connect the other side to MAV050.
Step #9) Readjust screen, size, brightness etc. Use the user controls and
user guide. Make BNC is used for this step.
Step #10) Place the front Bezel onto the frame and fasten screws. Use the
double sided tape provided the keep MAP307 in place. Use zip ties to have
the wires into organized fashion. Fasten the back cover & top cover back
onto the controller. You're ready to go.
Plug the MALE BNC
of test connector
into the IN BNC on
the monitor
Plug this side into
your DVD Player
MAV050
MAV003
Unplug BNC connector
and then plug
MAV050 into here.

M20A03-CT509
8
For Technical Support, Call
1-877-493-6105
[e-mail]
20 Howard Place
Kitchener, Ontario N2K 4Z4
CANADA 519.725.222
Enjoy your rejuvenated Monitor.
Call us to order more replacement parts.
Keep your Panelview 550 up and running!
LED backlight MB550E
Touchscreen MF550T
Fiber optic MB550FOS
Keypad MF550K
Fiber optic MB55FOL
Keypad-touchscreen
MF550B