Monster MH72002 User manual

Monster Bluetooth Headphones
Model: MH72002
Quick Start Guide
Please read this Quick Start Guide carefully and keep it for future use.
Product Overview:
Earphones (Left & Right)
Charging Case
Eartips x 3 Pairs (S, M & L)
USB-C Charging Cable
Quick Start Guide & Warranty letter
1. Multi Function Button (MFB）
2. LED Indicator
3. Earphone - Charging Contacts
4. Eartip
5. Charging Case - Charging Pins
6. Charging Case - Battery LED Indicator
7. USB-C Charging Port
8. Reset Button
8
7
1
4
2
35
6

Power On/Off
The earphones will automatically turn on after removing from the charging case.
To turn off the earphones, put back to the charging case. Earphone’s light indicator is on and
starts charging, the earphones will automatically turn off. When the LED indicator is off, it is
fully charged.
Experiment with the different sizes of ear tip to find your perfect fit.
Pairing
Remove earphones from the charging case, the earphones will turn on automatically. Left and
right earphones will be connected automatically. Wait for a few seconds, “pairing” voice prompt
will be heard.
For new device connection, go to the Bluetooth settings on your mobile device and set it to
search for new devices (new Monster device). Once the earphone is paired, you will hear
“connected”.
Volume Control
To decrease/increase the volume level, quickly double press the MFB on the left/right
earphone during music streaming.
Calling
Short press the MFB to answer/end a phone call, long press the MFB about 2 seconds to
reject a phone call.
Music
Short press the MFB once to play/pause music. To play the previous/next song, press and
hold left/right MFB for around 2 seconds
Voice Control
After connecting to the phone, quickly press the MFB three times on the left earphone to
activate the voice assistant.

Game and music modes
Music is the default mode.
Quickly press the MFB three times on the right earphone, to switch between game and
music modes, corresponding voice prompt “game mode” or “music mode” will be heard.
Reset
Put the earphones back to the charging case, both LED indicators will be turned on to
indicate earphones are charging. Then long press the reset button for around 3 seconds,
The LED indicators flash three times. Earphones reset successfully, remove earphones
from the charging case, the earphones will turn on automatically. Left and right earphones
will be connected automatically. Wait for a few seconds, “pairing” voice prompt will be
heard.
LED Indicator Guide
Status Description Voice Prompt
Power On Blue LED indicator stays on about 1 second “Power On”
Power Off Blue LED indicator stays on about 1 second “Power Off”
Pairing Blue LED indicator flashes continuously “Pairing”
Music Mode (Connected) LED indicator is off “Connected”
Game Mode (Connected) Blue LED indicator flashes every 6 seconds -
Charging – Earphones Blue LED indicator stays on -
Charging – Charging Case Battery LED Indicator flashes while
charging. When battery LED indicator is off,
it is fully charged.
-
Charging Case Battery Low Battery LED Indicator flashes five times
when battery case is activated. -
FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.