Monster MTH9-1001-BLK User manual

MTH9-1001-BLK
V4.0 1020
Operation Manual
HDTV WIRELESS
HEADPHONES KIT
with Bluetooth®Audio Transmitter
and Bluetooth®Headphones
Scan QR Code for
Quick Setup Video

Features
What’s Included
Introduction
• Add Bluetooth audio capability to your TV or home stereo
• Stream audio up to 33ft
• Watch TV without disturbing others
• Easy installation and pairing
• Bluetooth Audio Transmitter
• Bluetooth Headphones
• 3.5mm Aux Cable - 1.5ft (0.5m)
• Micro USB Charging Cable x2 - 3ft (1m) each
• USB Wall Charger
• Self-adhesive Transmitter Mount
• User Manual x1 pc
This HDTV Wireless Headphones Kit with Bluetooth®Audio
Transmitter and Bluetooth®Headphones conveniently streams
audio from TV’s and gaming systems to Bluetooth®
headphones, soundbars or speakers up to 33ft away.
Warning
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s warranty or authority
to operate the equipment. Risk of explosion if the battery is replaced
by an incorrect type. Wall mounting height is less than 2M.

Controls, at a Glance
LED Indicator
Micro USB
Charging Port
3.5mm Aux Jack
Volume Up/
Next Track
Multifunction
Button
Press+Hold - Power/Pair
Press - Play/Pause
Press - Answer/End Calls
Press+Hold - Volume
Press - Track
Press+Hold - Volume
Press - Track
Single Press - Pair
Double Press - Break Pair
Initiates Auto-Pairing
Volume Down/
Previous Track
Mic
Bluetooth
Transmitter
Bluetooth
Headphones
Bluetooth Button/LED
Micro USB
Charging Port
Charging Indicator
3.5mm Jack
Power Switch

Get Started
STEP 1: Charge
1Using included (or any) micro USB cable and USB power
source, charge both your Monster Bluetooth Transmitter
and Monster Bluetooth Headphones until full.
For best performance, it is recommended to fully charge both
devices before the first use (estimated charge time: 3hrs each)
STEP 2: Install the Bluetooth Transmitter
Note: The Transmitter includes an optional, peel-and-stick mounting
bracket that can conveniently attach it to the back of your TV.
2
3
Connect the Transmitter to an audio source, like a TV or
home stereo, using the 3.5mm audio jack and the included
3.5mm Aux Cable. Be sure that it is connected to the
AUDIO OUTPUT jack of the audio source, not an input.
Note: After connecting the Transmitter, you may need to
adjust your TV’s audio output to select the 3.5mm output.
For prolonged use in this location, connect the transmitter to
one of your TV’s USB ports, or a separate USB power
source, using the USB cable.
Bluetooth
Headphones
+
Bluetooth
Transmitter
LED charging indicator (next to the USB port)
Solid RED - charging / GREEN - fully charged
LED indicator (next to the USB port)
Solid RED - charging / OFF - fully charged
Bluetooth Button/LED

Note: Auto Pair should take no more than 5 seconds to complete.
If you have not heard the 2-note chime indicating pairing
success, Press the button on the Transmitter ONCE.
DO NOT press+hold this button as it may reset the device.
For info on manually pairing the Transmitter to a different
Bluetooth Audio Device, like earbuds or speakers, or manually
pairing the Headphones to a different Bluetooth Audio Source,
like a tablet or phone, please see pg 6.
Note: The Transmitter includes an optional, peel-and-stick mounting
bracket that can conveniently attach it to the back of your TV.
STEP 3: Auto Pair the Bluetooth Headphones
Pairing with Other Devices
5
6
Press+Hold the Multifunction Button on the Headphones
for 3 seconds to turn on the Bluetooth headphones, you will
hear a 3-note chime indicating that it has turned on.
The LED indicator with begin quickly flashing red and blue
indicating it has entered Auto Pairing Mode. The Headphones
and the Transmitter will automatically pair with each other.
You will hear a 2-note chime indicating that they have paired
successfully and the LEDs will pulse blue.
4Turn on the Transmitter by switching the power switch on the
side to the “ON” position. The Bluetooth LED indicator will
illuminate solid blue.
Bluetooth indicator (on the button)
Solid Blue - ready to pair / BLUE slow flash - paired
LED indicator (next to the USB port)
RED&BLUE fast flash - pairing / BLUE slow flash - paired

Note: Auto Pair should take no more than 5 seconds to complete.
If you have not heard the 2-note chime indicating pairing
success, Press the button on the Transmitter ONCE.
DO NOT press+hold this button as it may reset the device.
Press+Hold the Multifunction Button on the Headphones
for 3 seconds to turn on the Bluetooth headphones, you will
hear a 3-note chime indicating that it has turned on.
The LED indicator with begin quickly flashing red and blue
indicating it has entered Auto Pairing Mode. The Headphones
and the Transmitter will automatically pair with each other.
You will hear a 2-note chime indicating that they have paired
successfully and the LEDs will pulse blue.
Bluetooth indicator (on the button)
Solid Blue - ready to pair / BLUE slow flash - paired
LED indicator (next to the USB port)
RED&BLUE fast flash - pairing / BLUE slow flash - paired

If desired, the Transmitter can stream audio to any other Bluetooth
enabled audio device, like earbuds, headphones, or speakers.
Ensure the Headphones are OFF before re-pairing the Transmitter.
If desired, the Bluetooth Headphones can be paired to any
Bluetooth enabled device, like phones, tablets, or computers.
Ensure the Transmitter is OFF before re-pairing the Headphones.
Manually Pair the Headphones
to a different Bluetooth Audio Source
1
2
3
Enable Bluetooth search mode on your audio device
(follow the individual instructions for your device)
Turn on the Bluetooth headphones by pressing and
holding the Multifunction Button for 3 seconds, you
will hear a 3-note chime indicating that it has turned on.
The LED indicator will begin quickly flashing blue and red
indicating it has entered Auto Pairing Mode.
Locate and select device “MONSTER MTH9-1001” in
your device’s Bluetooth list to complete pairing
Manually Pair the Transmitter to a
different Bluetooth Audio Device
1
2
To manually enter pairing mode on the Transmitter, Press
the button ONCE. The Bluetooth LED indicator will flash
blue quickly indicating it has entered Pairing Mode.
Activate pairing mode on your Bluetooth audio device (follow
the individual instructions for your device). The Transmitter
will locate and automatically pair to the available device,
allow up to 20 seconds for the Transmitter to pair.
Pairing To
Other Devices
Note: The headphones and
transmitter can each only connect
to one device at a time.

If desired, the Transmitter can stream audio to any other Bluetooth
enabled audio device, like earbuds, headphones, or speakers.
Ensure the Headphones are OFF before re-pairing the Transmitter.
Press+Hold Button to raise the volume
Press+Hold Button to lower the volume
Press+Hold Button to raise the volume
Press+Hold Button to lower the volume
Press Button to play/pause audio and to
answer/end phone calls
Press Button to change to the next track
Press Button to change to the previous track
Headphones
Operation
To Use as Wired Auxiliary Headphones:
Plug a 3.5mm audio cable into the Aux jack (additional cable
not included). The headphones will automatically switch from
“Bluetooth” mode to “Auxiliary” mode and power off to conserve
battery. The Headphones do not need to be ON in Aux mode.
Note: Volume and music control buttons on the
headphones will not function while in Aux mode.
1
2
3
Press+Hold the Multifunction Button for 3 seconds
to turn on the Bluetooth headphones. (If the Transmitter is
ON, the Headphones will automatically reconnect, you will
hear a 2-note chime indicating success.)
Use the buttons to control your audio. You will have different
controls based on what device you are connected to:
To power down the headphones, hold the Multifunction
Button for 5 seconds, the LED light indicator will flash
red 3 times and then remain off. You will hear a 4-note chime
indicating that they have successfully powered off.

Press+Hold Button to raise the volume
Press+Hold Button to lower the volume
Press+Hold Button to raise the volume
Press+Hold Button to lower the volume
Press Button to play/pause audio and to
answer/end phone calls
Press Button to change to the next track
Press Button to change to the previous track
To power down the headphones, hold the Multifunction
Button for 5 seconds, the LED light indicator will flash
red 3 times and then remain off. You will hear a 4-note chime
indicating that they have successfully powered off.
Safety
Instructions
Please read and understand all instructions before using
this product. If damage is caused by failure to follow the
instructions, this warranty is null and void.
• Keep these instructions.
• Do not drop, puncture, or disassemble this product.
• Do not expose this product to dripping or splashing of
drinks or liquids of any kind.
• Avoid long exposure to direct sunlight, which may cause
damage.
• Do not expose this product to open flames.
• Do not use the product in a strong magnetic field.
• Use a clean, soft cloth to clean. Do not use any corrosive
cleaners/oils to clean.
• Do not attempt to repair the device or open the unit as this
will void the warranty.

The illustrated products and specifications may dier slightly from those supplied.
The M Monster logo is a registered trademark of Monster, Inc. or its subsidiaries in the
U.S. and other countries and are used under license. All other brand names are
trademarks of their respective owners. Neither Jem Accessories, Inc. nor Monster, Inc.
is aliated with the respective owners of their trademarks. Licensed and
Manufactured by Jem Accessories, Inc. South Plainfield, NJ 07080. Made in China.
Customer
Service
[email protected]
866-246-2008
FCC Statement
FCC Radio Frequency Exposure Statement
In the event this product becomes defective,
please do not return this product to your retailer.
This device complies with Part 15 of the FCC Rules. Operation is
subject to following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure
requirements. The device can be used in fixed or mobile condition.
The minimum separation distance is 20cm.
1 Year Limited Warranty
Scan QR code for warranty information