Montgomery Ward GD-2TCCTW User manual

Instruction Manual
Item No.: 724718
120V~, 60Hz, 580W
Wards.com 1•888•557•3848
Montgomery Ward Customer Service
1112 7Th Avenue, Monroe, WI 53566
8:00 am to Midnight, Monday through Friday
Wards.com 1•888•557•3848
Countertop Water
Dispenser
Hot & cold
war where
you want it
Model: GD-2TCCTW

Thank you for purchasing your Countertop Water Dispenser by
Montgomery Ward®. It will perform to the highest standard, time after time,
with all the convenience and durability you rely on from Wards.
We guarantee it!
You will love the convenience of hot and cold water where you want it,
when you want it. All you need is bottled water and an electrical outlet –
no plumbing required!
3
PLEASE READ THESE INSTRUCTIONS BEFORE USE
Basic safety precautions should always be followed when using this appliance.
WARNING: TO AVOID THE RISK OF ELECTRICAL SHOCK, ALWAYS MAKE
SURE THE PRODUCT IS UNPLUGGED FROM THE ELECTRICAL OUTLET BE-
FORE ASSEMBLING, DISASSEMBLING, RELOCATING OR CLEANING
1. Close supervision is necessary when any appliance is used by or near children.
Do NOT allow children to play with this appliance.
2. To protect against electrical shock, do not place cord, plug or appliance in water
or other liquid.
3. Use the plug to disconnect from electrical outlet, never pull out by the cord.
4. Turn power OFF before removing plug from outlet.
5. Never remove plug with wet hands.
6. Do NOT operate any appliance with a damaged cord or plug, or after the
appliance malfunctions or has been damaged in any manner. Call our toll-free
customer service number for information regarding replacement or returning
the product.
7. Do NOT allow water to get on Control Panel.
8. Do NOT expose to direct sunlight.
9. Do NOT use outside.
10. Never install the unit where it could be subjected to:
• Other products that produce heat (furnace, stove, etc.).
• Flammable materials, including liquids.
• Excessive dust.
• Moisture.
11. Indoor use only.
12. Do NOT use abrasive cleansers or pads to clean outside of water dispenser.
13. Do NOT use water bottles with cracks, holes or leaks.
14. When moving Water Dispenser, do NOT angle more than 45°.
15. Never add bleach, detergents or other hazardous chemicals to the water tanks.
16. Never store paint, gasoline, oil or other flammable liquids near Water Dispenser.
17. Do NOT use appliance for other than intended use.
18. Discard appliance following local ordinances.
Important Safeguards........................... 3
3-Prong Plug......................................... 4
Parts & Features................................... 4
Installation ............................................ 5
Before Using for the First Time............. 5
How to Use........................................... 6
General Care and Storage ................6-7
Troubleshooting .................................... 8
Warranty & Return Information......10-11
Table of Contents
21•888•557•3848
Wards.com
Important Safeguards
PLEASE SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS FOR HOUSEHOLD USE ONLY
© 2015 Montgomery Ward, Inc. All rights reserved.
ank you
for your
purchase!
3102543
Conforms to UL Std. 471
Certified to CSA Std. C22.2 No. 120-13

41•888•557•3848
Wards.com
45
Parts & Features
3-Prong Plug
This appliance has a 3-prong (grounding) plug for use in a 3-prong (grounding) out-
let to minimize the possibility of electric shock. This appliance should only be used
with a 120V, 60Hz grounded outlet. Failure to follow these instructions could result in
fire, electrical shock, serious injury or death.
If the plug does not fit fully in the outlet, contact a qualified electrician to install a
3-prong (grounding) outlet. Do not attempt to modify the plug in any way. Failure to
follow these instructions could result in fire, electrical shock, serious injury or death.
WARNING: Plastic bags pose a risk of suffocation. Never allow children to play with
plastic bags.
1. After unpacking, dispose of all packing materials in accordance with local ordinances.
2. Place Water Dispenser on a counter strong enough to support the weight of the
appliance when fully loaded with water.
3. Water Dispenser should have a minimum of 2 inches of clearance around the
entire unit to allow for adequate ventilation.
4. Level the appliance using the adjustable leveling feet on the front of the unit.
5. Allow unit to sit upright and undisturbed for 2 hours.
Note: Do NOT plug unit into electrical outlet.
1. Hot/Cold Water Switches on back (not shown) 6. Cold Water Button
2. Control Panel 7. Cold Water Dispenser
3. Hot Water Button with Safety 8. Removable Drip Tray
4. Hot Water Dispenser 9. Adjustable Legs
5. Water Intake
Installation
Before Using for the First Time
1. Check that the drain plug cap, which is located on the back lower right corner, is
firmly in place.
2. Fill water tank to capacity with tap water and let sit for 5 minutes.
3. Place cup under hot water dispenser, slide red tab to the right and press hot
water button just until water flows out of dispenser.
4. Plug Water Dispenser into electrical outlet.
5. Wait 1 hour for hot and cold water to come to temperature.
6. Unplug the Water Dispenser.
7. Place a large container under the hot and cold dispensers and drain unit using
the hot and cold water buttons.
8. Place a container under the drain plug on the back of the unit, remove cap and
allow remaining water to drain.
9. Replace cap on drain plug.
10. Install bottled water in water intake (up to 5-gallon capacity).
11. Place a container under the hot and cold water dispensers.
12. Press both water buttons just until water starts flowing from dispensers.
13. Plug Water Dispenser into electrical outlet.
Drain plug located on
back of unit.
1
2
3
4
5
6
7
8
9

76 1•888•557•3848
Wards.com
How to Use
IMPORTANT: Follow the instructions in the section Before Using for the First Time,
on page 5, before using this appliance for the first time or after a long period of
disuse.
1. Turn cooling switch to OFF.
2. Unplug Water Dispenser from the electrical outlet.
3. Remove label, if applicable, from lid of water bottle.
4. Install water bottle into water intake (up to 5-gallon capacity).
5. Place cup under hot water dispenser and press hot water button until water is
dispensed.
6. Plug unit in.
7. Turn cooling and/or heating switch(es) to ON; the LED will display on the control
panel.
General Care & Storage
This appliance contains no user serviceable parts. Do not try to repair it yourself. If
problems occur, call our toll-free customer service number for information regarding
replacement or returning the product.
PRECAUTIONS:
• Always unplug machine before cleaning.
TO CLEAN:
• For general cleaning, wipe the front and back of the Water Dispenser
with a soft, damp cloth. Do NOT use abrasive cleansers or pads to clean
outside of machine.
If the water flow from the dispensers has slowed down or doesn’t come out in an
even flow, minerals from the water might have built up causing a blockage. In this
case, you will need to clean the inside of the machine using a solution of tap water
and 2% citric acid.
1. Turn the cooling switch to OFF.
2. Unplug the Water Dispenser.
3. Remove water bottle and set aside.
4. Place a large container under the hot and cold dispensers and drain unit using
the hot and cold water buttons.
5. Place a container under the drain plug on the back of the unit, remove cap and
allow remaining water to drain. Replace cap.
6. Fill water intake with citric acid solution and let it sit for 2 hours.
7. Place a large container under the hot and cold dispensers and drain unit using
the hot and cold water buttons.
8. Place a container under the drain plug on the back of the unit, remove cap and
allow remaining water to drain. Replace cap.
9. Replace water bottle in water intake.
10. Place cup under hot water dispenser and press hot water button until water
flows from dispenser.
11. Plug unit back in.
12. Turn the cooling and/or heating switch(es) to ON.
13. Wait 1 hour for water to come up to temperature.
TO STORE:
If the Water Dispenser will not be used for 3 days or more, it’s best to drain water
from the unit to avoid mineral buildup.
1. Turn the cooling switch to OFF.
2. Unplug the Water Dispenser.
3. Remove water bottle and set aside.
4. Place a large container under the hot and cold dispensers and drain unit using
the hot and cold water buttons.
5. Place a container under the drain plug on the back of the unit, remove cap and
allow remaining water to drain. Replace cap.
6. Wipe out any water or moisture remaining in water intake using a soft cloth.
General Care & Storage (cont’d)

89
1•888•557•3848
Wards.com
Troubleshooting
Problem Possible Cause Remedy
Water Dispenser doesn’t
dispense water
No power to unit Plug unit in
Check for tripped circuit
breaker or blown fuse
Cold water is not cold Cooling switch not on
Proper clearance not
maintained
Turn cooling switch to ON
position
Make sure there is 2
inches of clearance on all
sides of machine
Hot water is not hot Hot water switch not on Turn on hot water switch
on back of unit
Compressor turns on and
off frequently
Ambient temperature is
above 107° F
Cool ambient tempera-
ture where Water
Dispenser is located
Water Dispenser vibrates Unit is not level Level machine using the
adjustable feet
Water Dispenser is noisy Flow of refrigerant in unit
causes gurgling sound
Unit is not level
This is normal operation
Level machine using the
adjustable feet
This page intentionally left blank.