Montigo Divine H36PV Instruction Manual

XG0649 - 080921
Installation & Maintenance Manual
®
C
US
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury,
death, or property damage.
—Donotstoreorusegasolineorotherammablevaporsand
liquidsinthevicinityofthisoranyotherappliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phoneinyourbuilding.
• Leavethebuildingimmediately.
• Immediatelycallyourgassupplierfromaneighbour's
phone. Follow the gas supplier’s instructions.
• Ifyoucannotreachyourgassupplier,callthere
department.
—Installationandservicemustbeperformedbyaqualied
installer,serviceagencyorthegastter.
DivineH36PV
POWERVENTFLUSHFACEFIREPLACE
Read and understand this manual. Improper installation, adjustment,
alteration, service or maintenance can cause serious injury, property
damage or even death. For assistance or additional information
consult a qualied installer, service agency or the gas supplier.
A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and
must be installed for the protection of children and
other at-risk individuals.
HOT GLASS WILL
CAUSE BURNS.
DONOTTOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
Installation and service must be performed by a qualied installer,
service agency or the gas tter.
Installer: Leave this manual with the appliance.
Consumer:Retain this manual for suture reference.
NOTICE
CAUTION
DANGER
DANGER
Some materials used in the manufacturing process of this product can
expose you to Benzene which is known in the State of California to
cause cancer and birth defects or other reproductive harm. For more
information go to www.P65warnings.ca.gov
WARNING
DISCONTINUED ITEM
THIS ITEM HAS BEEN DISCONTINUED AND IS
NO LONGER IN PRODUCTION.
PLEASE CONTACT YOUR LOCAL MONTIGO DEALER
REGARDING MAINTENANCE AND SPARE PARTS AVAILABILITY.

Page 2 XG0649 - 080921
Table of ContentsTable of Contents
H36PVN Power Vent Indoor Gas Fireplace
You must read and understand this manual prior to installation, operation or
troubleshooting this appliance. Please retain this owner’s manual for future reference
and maintenance.
NOTICE
Instruction Manual Contents
Safety Alerts 3
Introduction 3
Section A: Before You Start 4
Pre-Installation Checklist 4
Rating Plate Sample 5
Section 1: Installation Overview and Product Dimensions 6
Clearances 6
Section 2: Framing 7
Section 3: Finishing 9
Fireplace Facing 9
Mantels & Surrounds 9
Section 4: Installing the Power Vent 10
Installing a Roof Mounted Vertical Exterior Power Vent (EDVRSPV58) 10
Venting Layout - Roof Mounted Vertical Exterior Power Vent 10
Venting Components 11
Venting Layout - Wall Mounted Vertical Exterior Power Vent 14
Section 5: Wiring 21
Conduit & Wiring clearances 24
Section 6: Installing the Gas Line 25
FUEL CONVERSION 25
GAS PRESSURE 25
GAS CONNECTION 25
Section 7: Installing & Removing the Screen and Door 26
Section 8: Installing the Log Set 28
Section 9: Operation - Start up Sequence 30
Standing (Continuous) Pilot Ignition (SIT NOVA 820) 30
Section 10: Maintenance 31
Removing the Log Grate: 31
Removing the Refractory: 31
Removing the Stand-o󰀨 Panels: 32
Removing the Access Panel: 32
General 33
Cleaning 33
Troubleshooting (only to be done by qualied service personnel): 34
Replacement Parts: 34
Appendix A: Power Vent Locations 35
Appendix B: Warranty 37
Appendix C: State of Massachusetts 38

Page 3
XG0649 - 080921
H36PVN Power Vent Indoor Gas Fireplace
Safety Alert KeySafety Alert Key
IntroductionIntroduction
Introduction
Congratulations on your purchase of a Montigo Fireplace.
With over 30 years of experience, Montigo is committed to
providing you with a gas replace that is not only a beautiful
addition to your space, but that is also designed and manufactured
to the highest safety, reliability and engineering standards.
We strongly encourage you to read and carefully follow
the instructions laid out in this Installation, Operation and
Maintenance Manual and retain it for your future reference.
Pay special attention to all cautions, warnings, and notices
throughout this manual intended to ensure your safety.
This manual covers installation, operation and maintenance.
Lighting, operation and care of this replace can be easily
performed by the homeowner. All installation and service work
should be performed by a qualied or licensed installer, plumber
or gas tter as certied by the state, province, region or governing
body where the replace is being installed.
This installation, operation and maintenance manual is applicable
to the models described below. Refer to your rating plate to
verify included options.
Warranty and Installation Information: (See Appendix B)
The Montigo warranty will be voided by, and Montigo disclaims
any responsibility for, the following actions:
► Modication of the replace and/or components including
Direct-Vent assembly or glass doors.
► Use of any component part not manufactured or approved
by Montigo in combination with this Montigo replace system.
► Installation other than as instructed in this manual.
Consult your local Gas Inspection Branch on installation
requirements for factory-built gas replaces. Installation & repairs
should be done by a qualied contractor.
Fireplace BTU/H Input
Model# Natural Gas Propane Venting Type Burner Type Ignition Type
H36PVN 55,000 --- Top Power Vent Traditional IPI Electronic Ignition
Young children should be carefully supervised when they are
in the same room as the applicance. Toddlers, young children
and others may be susceptible to accidental contact burns. A
physical barrier is recommended if there are at risk individuals
in the house. To restrict access to a fireplace or stove, install
an adjustable safety gate to keep toddles, young children and
other at risk individuals out of the room and away from hot
surfaces.
CAUTION
Indicates a hazardous situation which, if not
avoided, WILL result in death or serious
injury or property damage.
Indicates a hazardous situation which, if not
avoided, COULD result in death or serious
injury or property damage.
Indicates a hazardous situation which, if not
avoided, WILL result in minor or moderate
injury.
Address practices that are important, but
not related to personal injury
DANGER WARNING
CAUTION NOTICE
Safety Alerts

H36PVN Power Vent Indoor Gas Fireplace
Page 4 XG0649 - 080921
InstallationInstallation
Section A: Before You Start
Important Message
Save these Instructions
The H36PV Power Vent replaces must be installed in
accordance with these Instructions. Carefully read all the
Instructions in this manual rst. Consult the Local Gas Branch to
determine the need for a permit prior to starting the installation.
It is the responsibility of the installer to ensure this replace is
installed in compliance with the manufacturers instructions and
all applicable codes.
BEFORE YOU START:
Pre-Installation Checklist
■ Determine the desired install location of your replace.
■ See Section 1, Dimensions on Page 5, and refer to the
Framing Section 2 for details.
■ Select your type and location of your Power Vent
run: Roof Mounted (EDVRSPV58) or Wall Mounted
(EDVWSPV58) or LDVPV58 (Inline Power Vent).
■ Your termination location should be selected to provide
the shortest possible vent run.
■ Lay out the Vent run; calculating the required elbows
and straight runs of 5"/8" ex and/or rigid pipe.
■ Refer to the Section 4 on Page 10, "Installing the Power
Vent" for details.
■ Montigo supplies 20' of low voltage wire, which can be
spliced to any length. This wire CANNOT run in conduit
with any other wire.
■ Refer to Section 5 on Page 18, for Wiring Details.
■ The gas connection is located on the bottom side of the
replace.
■ Refer to local codes and guidelines for installation
requirements.
■ Installation and repairs should be done by a qualied
contractor and must conform to:
• Installations in Canada must conform to the
current CAN/CGA B-149.1 and .2 Gas Installation Code and
local regulations.
• Installations in the USA must conform to local
codes, or in the absence of local codes to the National
Fuel Gas Code, ANSI Z223.1.
• SeeAppendix C for installation within the State
of Massachusetts. This replace must comply with
NFPA-54 Chapter 10.
■ Refer to Section 6 Page 24, "Installing the Gas Line" for
Details.
Understanding the Basic Operation
Residential H36PV replace
To operate the replace, Montigo has supplied and installed
twenty feet of low voltage wire to this electrical control panel.
Connect the two wire harness to a standard single pole ON/
O󰀨 switch located at a location of your choice. You may also
extent these wires to any length, as long as you select a wire
of equal quality.
Due to high operating temperatures, this appliance should be located out of traffic &
away from furniture and draperies.
Children and adults should be alerted to the hazards of the high surface temperature,
which could cause burns or clothing ignition.
Young children should be carefully supervised when they are in the same room as the
appliance.
Clothing or other flammable materials should not be placed on or near the appliance.
CAUTION
When this appliance is installed directly on any combustible material other than wood
flooring, it must be installed on a metal or wood panel extending the full width and
depth of the appliance or a fire will occur causing serious injury, property damage or
even death.
DANGER
Installation and repairs should be done by an authorized gas fireplace service technician.
The appliance should be inspected before use and at least annually by a professional. More
frequent cleaning may be required due to excessive lint from carpeting, bedding material,
etc. It is imperative that control compartments, burners and circulating air passageways of
the fireplace are kept clean.
NOTICE
WARNING
Any safety screen, guard, or barrier removed for servicing an appliance must be replaced
prior to operating the appliance.

H36PVN Power Vent Indoor Gas Fireplace
Page 5
XG0649 - 080921
InstallationInstallation
Rating Plate Sample



 












LB1225 Rev5.0 IPI-PV with screen 2015.03.02
  










 


    




  

  


  



    







 
 
 


 



Teklynx LabelView Demo
Figure A: Rating Plate for IPI eletronic ignition

H36PVN Power Vent Indoor Gas Fireplace
Page 6 XG0649 - 080921
InstallationInstallation
Section 1: Installation Overview and Product Dimensions
Please review the Pre-Installation Checklist on Page 4
for general information on preparing for a successful
installation of your replace.
The H-Series H36PVN & replace
The H36PVN replaces may be installed in any location that
maintains proper clearances to air conditioning ducts, electrical
wiring and plumbing. Safety, as well as e󰀩ciency of operation,
must be considered when selecting the replace location. Try
to select a location that does not interfere with room tra󰀩c,
has adequate ventilation, and o󰀨ers an accessible pathway for
Power Vent installation.
The replace dimensions are shown below:
Clearances
To ensure the H-Series H36PVN Fireplaces operate safely, all
models must maintain the following clearances.
*Note: Finishing hardwood, laminate ooring, or tile may be placed
directly in front of replace, however Montigo waives responsibility for
discoloration of ooring materials. Ability to withstand heat should be
discussed with the ooring manufacturer. If carpet is to laid there must
be a 12" clearance or hearth between the front of the replace and the
start of the carpet.
Clearances to Combustibles
Model# Top Sides Back Floor
(under)
Floor
(front)*
H36PVN 8" 0" 1" 0" 0"
Figure 1. Fireplace dimensions.
41 1
4
"
1049
46"
1168
2"
51
2"
51
91
8
"
230
31 3
8
"
797
1"
25
38 1
2
"
977
NAILING
FLANGE
NAILING
FLANGE
23"
583
14 3
8
"
364
2"
51
8"
203
5"
[127]
32 1
4
"
820
25 1
8
"
637
23"
585
MAIN
INCOMING
A/C POWER
CONNECTION
ACCESS
PANEL
83
4
"
221
ACCESS
PANEL
Front View
Side View
Top View

H36PVN Power Vent Indoor Gas Fireplace
Page 7
XG0649 - 080921
InstallationInstallation
Section 2: Framing
Step 1. To frame in the unit rst frame a rough-in enclosure with
combustible framing materials, using typical framing practices. The
rough-in frame opening for the assembled replace is 46" wide, x
50" high x 24" deep. See Figure 2.
NOTE: When constructing the framed opening, please ensure
that your combustible 2 x 4 header is at 50" minimum and
that there is access to install the gas line when the unit is
installed. See Figures 1 and 2a.
Step 2. Place the Fireplace in the enclosure and install the Vent pipe,
and Power Vent module. Next, Connect the Gas line and provide a
gas service shut-o󰀨 valve; according to local gas codes, then secure
in place with 1/4" wood screws. Install supplied Non-combustible
header at 45½" from oor.
46”
24”
50”
(minimum)
Flexible
incoming gas
connection
Secure nailing
flange to 2 x 4’s
using ¼" wood
screws.
Non-combustible Header (supplied by montigo), install to allow
15½” of Non-combustible cement board to fasten above the
glass of the unit and Non-combustible header.
Figure 2a. Fireplace installation, (Inlet Gas & Power Vent) .
Figure 2. Fireplace installation (combustible frame dimensions) Figure 2.aa Fireplace corner installation (combustible frame dimensions)
Note: Images are shown without screens for clarity purposes.
However, your replace should not be operated without proper
installation of screens.
80 15/16"
1"
61 1/4"
1"
NAME
CHECKED
DRAWN
THIRD ANGLE PROJECTION
DATE
FRACTIONAL
X.XX
X.XXX
ANGULAR:
DIM ARE IN INCHES
UNLESS OTHERWISE SPECIFIED
ALL BENDS ARE 90
1/8
.015
.005
1
50"
1:16
DWG. NO.
REV.
1 OF 1
A
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Monday, March 26, 2018 12:03:33 PM
SCALE:
H36PVFULL ASSEMBLY
H36PV
SHEET:
SIZE
A
CANADIAN HEATING
PRODUCTS
27342 GLOUCESTER WAY,
LANGLEY, BC, V4W 4A1
CF 7/18/2016
CF
3/26/2018
FULL ASSEMBLY
Y:\CADD\36\H36PV\Manual\H36 CORNER

H36PVN Power Vent Indoor Gas Fireplace
Page 8 XG0649 - 080921
InstallationInstallation
Section 3: Finishing
Step 1. As shown in Figure 3; Use Non combustible Cement board,
supplied by Montigo, screw to Non-combustible Header and 2 x 4's
at sides of unit (see gure 2a on page 6) using sheet metal screws.
Step 2. As shown in gure 3a; Cut standard Drywall / Wall board
to complete the installation of replace surround.
Non-combustible Cement Board
(supplied by montigo).
Fasten above the glass of the
unit to Non-combustible header
and 2 x 4’s at side of unit.
Combustible Drywall / Wall
Board or equivelant.
Fasten above the glass of the
unit to Non-combustible header
and 2 x 4’s at side of unit.
Figure 3. Non-combustible Cement Board the Fireplace, (supplied by Montigo).
Figure 3a.
Note: Images are shown without screens for clarity purposes.
However, your replace should not be operated without proper
installation of screens.

H36PVN Power Vent Indoor Gas Fireplace
Page 9
XG0649 - 080921
InstallationInstallation
Figure 3b. Combustible mantle and facings. (Not to scale)
Fireplace Facing
When selecting the nish material for your replace, it is important
to remember the following:
If the surround of the replace is to be painted to match the room decor,
heat-resistant paint must be provided . Also, decorative facing must
not extend past the replace opening at all, because it will interfere
with the access to retainers for removal of glass door and access to
the lower compartment.
Mantels & Surrounds
National Canadian Gas Association mantel test requirements are for
re hazard prevention to combustible materials.
Please be aware; temperatures over the mantel will rise above normal
room temperature and walls above replace may be hot to touch.
We recommend careful consideration be given to the effects of elevated mantel
temperatures which may be in excess of product design, for example: candles, plastic
or pictures. This can cause melting, deformation, discoloration or premature failure of
T.V. radio, and other electronic components.
CAUTION
CAUTION
When covering the upper metal portion of the
replace with a non-combustible material, please
Note: The decorative facing materials may be subject
to temperatures in excess of 250˚ F. This should be
considered when selecting facing materials.
CAUTION
Section 3: Finishing
Non-Combustible
Cement Board
(supplied by Montigo)
Non-Combustible
Cement Board
(supplied by Montigo)
Drywall/
Combustible Construction
To Ceiling
Horizontal Run
12” 11” 10” 9” 8” 7” 6” 5” 4” 3” 2” 1”
Vertical Run
Glass
16”
15”
14”
13”
12”
11”
10”
9”
8”
7”
6”
5”
4”
3”
2”
1”
Non-combustible
Header (supplied by
Montigo @ 6½”)
Combustible Construction
allowed in shaded area
First Combustible
Header @ 50"
from floor or 8”
from top of unit
Note: Images are shown without screens for clarity purposes.
However, your replace should not be operated without proper
installation of screens.

H36PVN Power Vent Indoor Gas Fireplace
Page 10 XG0649 - 080921
InstallationInstallation
Section 4: Installing the Power Vent
Figure 4b. Downward Venting Installations.
Figure 3.a Typical Venting Installations.
VentingInstallation
External Power Vent System must be used with a gas replace that is
equipped with electronic ignition system. When installing the venting,
the installation must adhere to the Vent Installation Section in the
replace's Installation Operation and Maintenance Instructions, as
well as the following guidelines:
• Ensure that the planned termination location is acceptable as
shown in Appendix A.
• Maximum allowed vent run is 100 feet.
InstallingthePowerVent
DownwardVerticalVenting
Downward venting installations are only possible with gas replaces
equipped with electronic ignition system. Battery backup cannot be
used with a power vent system.
Multi-Elbow
Installations
Multi-elbow installations are
possible up to a maximum of
six 90° elbows.
V
Max V Max Elbows
100’ feet six 90
Elbow 1
Elbow 2
Elbow 3
Elbow 5
Elbow 4
H2
H1
V1
V2
V3
Max V1 + H1 + V2 + H2 + V3 + H3 Max Elbows
100’ feet six 90
Max V1 + H1 + D + H2 + V3 Max Elbows
100’ feet six 90
Elbow 1
Elbow 2Elbow 3
Elbow 5
H1
V1
D = 6’ foot
MAX
V3
H2
Elbow 4
Vent Clamp
Framing Box
Vent
Chase
Power Head
Power Vent Components

H36PVN Power Vent Indoor Gas Fireplace
Page 11
XG0649 - 080921
InstallationInstallation
Venting Components
The following venting components and associated Montigo part
numbers are available for the PVVEX47-200:
Termination & Fan
Motor 4”/7” (Includes
mounting frame)
PV VEX47-200
Flex Sections MLF-1 (12" Section)
MLF-2 (24" Section)
MFL-3 (36" Section)
MFL 4 (48" Section)
Rigid Sections MEXT-1 (12" m/f Section)
MXT-20 (20" Section)
MEXT-2 (24" m/f Section)
MEXT-3 (36" m/f Section)
MEXT-4 (48" m/f Section)
Elbows MEL-90MM (m/m 90º Elbow
MEL-90FF (f/f 90º Elbow
MEL-90FM (f/m 90º Elbow)
MEL-45FM (f/m 90º Elbow)
Power Cord Harnesses EPVH-10 foot power cord & harness
EPVH-20 foot power cord & harness
EPVH-40 foot power cord & harness
EPVH-60 foot power cord & harness
EPVH-80 foot power cord & harness
EPVH-100 foot power cord & harness
Refer to Appendix A - Power Vent locations, to ensure the planned
Vertical Power vent location is acceptable.
Connection and installation of the vent components
should adhere to the following guidelines:
Use any combination of rigid and ex pipe as required and in any
orientation (Male connectors can face in any direction).
Flex sections may be stretched up to 50% of their total length (e.g.
a 24” section maybe stretched to 36”).
Ensure the pipe ends male to female slide in a minimum of 1 1/2”
of overlap.
Connect all vent sections using a minimum of three sheet metal
screws on the outer and inner pipe ue.
Ensure all runs are supported with a minimum of 3 supports per 10’
of venting.
When hanging/ supporting venting, ensure that 1” clearance is
maintained on sides and bottom of vent runs and 2” above horizontal
vent runs to any combustible material.
Rigid pipe may be cut less than half way from the female end only.
Ensure when cutting sections of rigid pipe to maintain integrity of
internal supports.
Place the springs, supplied with the pipe kit, between the outer and
inner pipes to keep the pipes separate and avoid any possible hot spots.
Montigo recommends the use of a ex section for the nal pipe
connected directly to the replace o󰀨ering greater exibility of
installation and absorption of movement.
Firestops must be installed as required by National & local codes.
When passing vent pipe through a wall use a heat shield.
Montigo recommends that all exterior corners and joints be
sealed with exterior caulking. However, we encourage you
to consult your Building Envelope Engineer or Waterproong
Consultant for further recommendations.
2.000
3.950
6.918
A
A
3.660
1.587
19.571
14.288
18.000
3.252
6.997
SECTION A-A
REV. DESCRIPTION DATE APPROVED
B WAS 24" BASE NOW 18" BASE 09/30/2019 -
1:6
SIZE
DWG. NO.
A
REV.
SHEET 2 OF 4
WEIGHT:
PVVEX47-200 FULL ASSEMBLY
K-FACTOR
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
DB
DATE
NAME
A
1/7/2021
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\Ventilation Systems\Roof Mounr Power Vent PVVEX47-200\PVVEX47-200 FULL ASSEMBLY
Thursday, January 07, 2021 10:05:31 AM
SCALE
MTK
PVVEX47-200
DIMENSIONS
2.000
3.950
6.918
A
A
3.660
1.587
19.571
14.288
18.000
3.252
6.997
SECTION A-A
REV. DESCRIPTION DATE APPROVED
B WAS 24" BASE NOW 18" BASE 09/30/2019 -
1:6
SIZE
DWG. NO.
A
REV.
SHEET 2 OF 4
WEIGHT:
PVVEX47-200 FULL ASSEMBLY
K-FACTOR
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
DB
DATE
NAME
A
1/7/2021
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\Ventilation Systems\Roof Mounr Power Vent PVVEX47-200\PVVEX47-200 FULL ASSEMBLY
Thursday, January 07, 2021 10:05:31 AM
SCALE
MTK
PVVEX47-200
DIMENSIONS
2.000
18.00
[457]
10.560
20.73 18.00
[457]
18.00
[457]
4
[126]
7
[203]
17.025
17.025
EDVRSPVF47
1:12
SIZE
DWG. NO.
A
REV.
SHEET 4 OF 4
WEIGHT:
PVVEX47-200 FULL ASSEMBLY
K-FACTOR
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
DB
DATE
NAME
A
1/7/2021
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\Ventilation Systems\Roof Mounr Power Vent PVVEX47-200\PVVEX47-200 FULL ASSEMBLY
Thursday, January 07, 2021 10:05:31 AM
SCALE
MTK
EDVRSPVF47 - 200
ROUGH IN KIT
2.000
18.00
[457]
10.560
20.73 18.00
[457]
18.00
[457]
4
[126]
7
[203]
17.025
17.025
EDVRSPVF47
1:12
SIZE
DWG. NO.
A
REV.
SHEET 4 OF 4
WEIGHT:
PVVEX47-200 FULL ASSEMBLY
K-FACTOR
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
DB
DATE
NAME
A
1/7/2021
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\Ventilation Systems\Roof Mounr Power Vent PVVEX47-200\PVVEX47-200 FULL ASSEMBLY
Thursday, January 07, 2021 10:05:31 AM
SCALE
MTK
EDVRSPVF47 - 200
ROUGH IN KIT
2.000
18.00
[457]
10.560
20.73 18.00
[457]
18.00
[457]
4
[126]
7
[203]
17.025
17.025
EDVRSPVF47
1:12
SIZE
DWG. NO.
A
REV.
SHEET 4 OF 4
WEIGHT:
PVVEX47-200 FULL ASSEMBLY
K-FACTOR
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
DB
DATE
NAME
A
1/7/2021
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\Ventilation Systems\Roof Mounr Power Vent PVVEX47-200\PVVEX47-200 FULL ASSEMBLY
Thursday, January 07, 2021 10:05:31 AM
SCALE
MTK
EDVRSPVF47 - 200
ROUGH IN KIT

H36PVN Power Vent Indoor Gas Fireplace
Page 12 XG0649 - 080921
InstallationInstallation
Figure 3.c Installing the Rough-in Kit.
Figure 3.e Unscrewing control cable cover
Figure 3.f Removing strain relief plate.
Figure 3.g
Vent Pipe
Control Cable
Step 1: Construct a chase box around the vent penetration with
dimensions as shown.
Step 2: Install the electrical
harness (EPVH-10-100) that
will communicate with the
Power Vent. Runvent pipe from
the replace to the chase. Make
sure the last section is female
end up and is ush with the
top of the chase without going
above it.
Step 3: Remove the last
section of vent pipe and put
o󰀨 to the side to be used later.
Step 4: Unscrew 6 screws
securing the control cable cover
and remove it.
Step 5: Unscrew 2 screws
securing strain relief plate and
remove it.
Step 6: Loosen nut on the
strain relief of the control cable.
Pass control cable through slot
in rough in box making sure the
nut stays is on the opposite
side of the rough in box as the
strain relief. Push the strain
relief through the hole in the
roughin box.
Step7: Reinstallthestrain relief
plate. Makesure the strainrelief
nut is above the strain relief
plate. Tighten the nut on the
strain relief.
2.000
3.950
6.918
18.000
18.000
18.000
17.500MAX
FINISHED CURB
17.500MAX
FINISHED CURB
16.250
.625
ROUGH IN KIT
EDVRSPVF47 ROUGH IN KIT
!IMPORTANT!
MAINTAIN AT LEAST
2.00" CLEARANCE
TO COMBUSTIBLES
ALL AROUND THE COLLAR
FRAMING DIMENSIONS
(NTS)
1:12
SIZE
DWG. NO.
A
REV.
SHEET 3 OF 4
WEIGHT:
PVVEX47-200 FULL ASSEMBLY
K-FACTOR
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
DB
DATE
NAME
A
1/7/2021
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\Ventilation Systems\Roof Mounr Power Vent PVVEX47-200\PVVEX47-200 FULL ASSEMBLY
Thursday, January 07, 2021 10:05:31 AM
SCALE
MTK
PVVEX47-200
FRAMING DIMENSIONS

H36PVN Power Vent Indoor Gas Fireplace
Page 13
XG0649 - 080921
InstallationInstallation
Figure 3.i Figure 3.n
Figure 3.j
Figure 3.k
Figure 3.l
Figure 3.m
Step 8: Push the molex
connector of the control cable
through the hole in the control
cable cover. Make sure the
molex clicks in place so it does
not fall out. Screw control cable
cover back in place.
Step 13: Place power vent
over chase and fasten with 4
screws on the vertical sides of
the base plate. Silicone of seal
the base plate in any location
necessary to keep the structure
of the building free of water or
moisture.
Step 9: Drop the rough in
box over top of and inside the
Chase.
Step 10: Take the last section
ofpipeand installthevent clamp
around the pipe. The bottom of
the band should be 6 3/8" from
the top of the pipe. Tighten the
clamp using the supplied nut
and screw.
Step 11: Drop pipe down into
the frame box. The pipe should
be ush with the top of the frame
box. Secure pipe connection
below.
Step 12: Connect power cable
of termination to the molex of
the control cable.
Step #4
Place termination head over chase
and fasten with 4 screws on the
vertical sides of the base plate.
Silicone or seal the base plate in
any location necessary to keep the
structure of the building free of
water or moisture.
20"
Max
20"
Max
10 5
8
"
270
Min
10 5
8
"
270
Min
24
Min
Vent Pipe
Control Cable
Step #1
Construct a chase box around the
vent penetration with the dimensions
as shown here.
Step #2
Install the vent pipe female end up 2"
- 3" from the top of the chase box.
Install the electrical harness (EPVH-
10-100) that will communicate with
the Power Vent module.
Step #3
Install the power vent Rought-in Kit.
Remove the electrical cover plate
from inside of the rough in kit. Pull
the control cable through the slot in
the bottom of the box and insert the
plug into the rectangular hole in the
cover plate. Re-attach the cover
plate. Pull wire harness throught the
supplied hole in the bottom corner of
the rough-in box and snap into the
slot provided.
6⅜
Attachment
screw
locations
ConduitandWiringClearances
Connect the power vent harness as outlined. Connect the wiring to the
replace as outlined in the schematic showin in Figure 14 Section 3.
Ensure that the proper clearances are maintained for the wiring and
conduit. When installing the wiring, it must never run above the vent
pipe and it must be at lest 1" clear of all venting and other hot surfaces.
1”Clearance
Wire
PowerVentWiring
C
Power Vent Wiring
BLUE BROWN BLACK WHITE
BLACK
GREEN
6 PIN MOLEX
CONNECTOR
KEY WAY
BLUE
AIR SWITCH
RED

H36PVN Power Vent Indoor Gas Fireplace
Page 14 XG0649 - 080921
InstallationInstallation
Figure 3.a Typical Venting Installations.
NOTE: Vent run for downward venting installations allows a maximum
of 40 feet including downward vent section. Maximum downward vent
section allowed is 6 feet.
VentingInstallation
External Power Vent System must be used with a gas replace that is
equipped with electronic ignition system. When installing the venting,
the installation must adhere to the Vent Installation Section in the
replace's Installation Operation and Maintenance Instructions, as
well as the following guidelines:
• Ensure that the planned termination location is acceptable as
shown in Appendix A.
• Maximum allowed vent run is 80 feet.
DownwardVerticalVenting
Downward venting installations are only possible with gas replaces
equipped with electronic ignition system.
Multi-Elbow
Installations
Multi-elbow installations are
possible up to a maximum of
six 90° elbows.
Max V + H Max Elbows
80’f eet six 90
Elbow 1
Elbow 2
Elbow 3
Elbow 5
Elbow 4
Elbow 6
H3
H2
H1
V1
V2
V3
Max V1 + H1 + V2 + H2 + V3 + H3 Max Elbows
80’ feet six 90
ü
ü
Max V1 + H1 + D + H2 Max Elbows
40 ’ f eet six 90
= 6' foot MAX

H36PVN Power Vent Indoor Gas Fireplace
Page 15
XG0649 - 080921
InstallationInstallation
14 1/4"
14 1/16"
12 1/8"
1 1/2"
7
9 11/16"
4 9/16"
12 5/16"
4
9 11/16"
14 1/4"
14 1/16"
12 1/8"
1 1/2"
7
9 11/16"
4 9/16"
12 5/16"
4
9 11/16"
14 1/4"
14 1/16"
12 1/8"
1 1/2"
7
9 11/16"
4 9/16"
12 5/16"
4
9 11/16"
14 1/4"
14 1/16"
12 1/8"
1 1/2"
7
9 11/16"
4 9/16"
12 5/16"
4
9 11/16"
Venting Components
The following venting components and associated Montigo part
numbers are available for the PVHEX47-200:
Termination & Fan
Motor 4”/7” (Includes
mounting frame)
PVHEX47-200
Flex Sections MLF-1 (12" Section)
MLF-2 (24" Section)
MFL-3 (36" Section)
MFL 4 (48" Section)
Rigid Sections MEXT-1 (12" m/f Section)
MXT-20 (20" Section)
MEXT-2 (24" m/f Section)
MEXT-3 (36" m/f Section)
MEXT-4 (48" m/f Section)
Elbows MEL-90MM (m/m 90º Elbow
MEL-90FF (f/f 90º Elbow
MEL-90FM (f/m 90º Elbow)
MEL-45FM (f/m 90º Elbow)
Power Cord Harnesses EPVH-10 foot power cord & harness
EPVH-20 foot power cord & harness
EPVH-40 foot power cord & harness
EPVH-60 foot power cord & harness
EPVH-80 foot power cord & harness
EPVH-100 foot power cord & harness
Refer to Appendix A - Power Vent locations, to ensure the planned
Vertical Power vent location is acceptable.
Connection and installation of the vent components
should adhere to the following guidelines:
Use any combination of rigid and ex pipe as required and in any
orientation (Male connectors can face in any direction).
Flex sections may be stretched up to 50% of their total length (e.g.
a 24” section maybe stretched to 36”).
Ensure the pipe ends male to female slide in a minimum of 1 1/2”
of overlap.
Connect all vent sections using a minimum of three sheet metal
screws on the outer and inner pipe ue.
Ensure all runs are supported with a minimum of 3 supports per 10’
of venting.
When hanging/ supporting venting, ensure that 1” clearance is
maintained on sides and bottom of vent runs and 2” above horizontal
vent runs to any combustible material.
Rigid pipe may be cut less than half way from the female end only.
Ensure when cutting sections of rigid pipe to maintain integrity of
internal supports.
Place the springs, supplied with the pipe kit, between the outer and
inner pipes to keep the pipes separate and avoid any possible hot spots.
Montigo recommends the use of a ex section for the nal pipe
connected directly to the replace o󰀨ering greater exibility of
installation and absorption of movement.
Firestops must be installed as required by National & local codes.
When passing vent pipe through a wall use a heat shield.
Montigo recommends that all exterior corners and joints be
sealed with exterior caulking. However, we encourage you
to consult your Building Envelope Engineer or Waterproong
Consultant for further recommendations.
9 3/4"
REF.
11 1/16"
11 1/16"
9 3/4"
10 9/16"
4
9.0
9 3/4"
REF.
11 1/16"
11 1/16"
9 3/4"
10 9/16"
4
9.0

H36PVN Power Vent Indoor Gas Fireplace
Page 16 XG0649 - 080921
InstallationInstallation
Step 2: Insert the Power Vent Rough-in Box as shown in Figure 4.a.
Fasten the Box securely in place with Screws or nails, Figure 4.a.
Apply exterior sheathing and nishing if required. (Figure 4.b).
Step 4: Insert the conduit from the Power Vent Module into the rough-
in frame through the two top right entry holes. Remove the nut from
the supplied strain relief and place as shown, Figure 4.c.
Step 7: Fasten Conduit mounting frame into place using existing
hardware, (6-pcs). (Coil conduit in behind cover.)
Step 5: Securely fasten bottom Collar pan into the Rough-in frame
using the existing hardware, (4-pcs). Tighten Strain Relief nut onto
Strain relief.
Step 6: Pull Power Vent Connector, (from behind) half-way through
supplied hole in conduit mounting frame, and snap into place, (notches
in two plastic wing clips. Orientation not critical).
Step 3: Next, remove the bottom collar and conduit mounting frame
as shown Figure 4.b. (Place removed hardware in a handy location
for re-assembly).
Framing
Rough-in Frame
Fasteners
PowerVentConduit
Strain Relief
Nut
Strain Relief
PowerVent
Conduit
Strain Relief & tightened nut
Power
Vent
Connector
Conduit
mounting
frame
Tightened hardware,
4-pcs.
Tightened hardware,
6-pcs.
Installed Power
VentConnector
InstallingthePowerVent
Selecting A Termination
Location
Before installing the
termination, ensure that
the proper air ow restrictor
is installed as shown, and
check to ensure the planned
termination location is
acceptable. For a detailed
illustration of allowed
termination locations, see
Appendix A.
Installing the External PV
Termination
Step 1. Construct a frame for
the termination opening to
12½" x 12½"
12 ‰
12 ‰
Figure 4.a Framing the Opening for Power Vent
Figure 4.b Installation of Rough-in Kit
Figure 4.c Installation of Power Vent Conduit
Figure 4.d Installing Conduit connector & conduit mounting frame
Figure 4.e Assembled Rough-in Kit

H36PVN Power Vent Indoor Gas Fireplace
Page 17
XG0649 - 080921
InstallationInstallation
Step 9: Install the Power Vent. Place the Power Vent into the Rough-in
frame, aligning the Power Vent into nal position. Ensure the Harness
is placed down in the Rough-in box when placing the Power Vent.
(Secure the Power Vent in Place with the supplied hardware).
Step 8: Install the Power Vent Power / communication harness. Hold
the Power Vent in close proximity of the assembled Rough-in Kit,
and plug in the Power Vent communication / Power Cord. (Note the
direction and orientation of the pins inside the Power Vent connector,
snap together). (Figure 4.e).
Connect the wiring to the external power vent termination as outlined
in the previous section, and connect the wiring to the replace as
outlined in the schematic below. Ensure that the proper clearances
are maintained for the wiring and conduit.
• When installing the wiring it must never run above the vent run
and it must be at least 1" clear of all venting.
Wiring Installation
1" min.
Vent
Cable
Montigo will not be held responsible for any water damage that may
occur from not installing the equipment as specied by this document.
WARNING
TOP of Power
Vent,
(Note Quantity of
louvers).
Note
louver
direction
Tightened hardware,
4-pcs.
Figure 4.f Installation of Power Vent communication harness
Figure 4.g Completed Installation of Power Vent

H36PVN Power Vent Indoor Gas Fireplace
Page 18 XG0649 - 080921
InstallationInstallation
Installing an In-Line Linear Power Vent (LDVPV58)
This section applies to installations where an external roof
or wall mounted power vent is not aesthetically acceptable
or feasible.
Venting Layout
Selection of components and details of venting lay out should
adhere to the following guidelines:
Ensure there is a minimum run of 2’ of straight pipe between
the replace and the power vent
Ensure the maximum vent run does not exceed 60'
Maximum vent run must be reduced by 10’ for 1’ of pipe
running in a vertical downward direction
Ensure the number of 90º elbows does not exceed 3 (maximum
allowable vent run must be reduced by 10’ for every additional
90º elbow added)
Ensure the number of 45º elbows does not exceed 6
Linear Power Vent - Horizontal Termination
Example A. Vertical mounting with horizontal termination
** from fireplace to in-line power vent
Maximum allowable vent run must be reduced by ten feet (10'-0"
for every additional 90° elbow added. With a snorkel Termination,
reduce the total vent run by an additional twenty feet (20'-0"). Figure's
7 and 7a.
Figure 7. Vertical Mounting for the Linear Power Venter
Figure 7a. Horizontal Vent for the Linear Power Venter.
Example B. Horizontal mounting with horizontal termination
** from fireplace to in-line power vent
Example C. Horizontal mounting with downward vent run and
horizontal termination
** from fireplace to in-line power vent
Maximum allowable vent run must be reduced by ten feet (10'-0")
for every additional 90° elbow added. Also, deduct ten feet (10'-0")
of vent length for every one foot (1'-0") of vent run traveling in a
downward direction.
Figure 7b. HorizontaI Linear Power Vent with Downward vent
and Horizontal Vent Run to Termination.
■ Vent terminations can be very hot. The termination is to be installed higher than 7 feet
above a public walkway.
■ Do not obstruct, or attempt to conceal, the vent termination. These actions will affect the
operation of the fireplace, and may be hazardous.
■ In heavy snow areas, take extra care to prevent snow buildup from obstructing the vent
termination.
CAUTION
Venting Installation
Maximum
Vent Run
Minimum
Vent Run**
Max. #
Elbows
60 Feet 2 Feet 3
Venting Installation
Maximum
Vent Run
Minimum
Vent Run**
Max. #
Elbows
60 Feet 2 Feet 3
Venting Installation
Maximum
Vent Run
Minimum
Vent Run**
Max. #
Elbows
40 Feet 2 Feet 3
2’-0 ”
MIN
Vertical Installed
Linear Power Vent
Horizontal Run Flex Pipe
Vertical
Flex Pipe
90deg
Elbow
90deg
Elbow
90deg
Elbow
Termination
Snorkel
Termination
LDVPV58
Flush
Termination
VLWB-8
Option
Option
LDVPV58
Horizonta
l
Insta
ll
e
d
Linear Power Vent
Horizontal Run Flex Pipe
Vertical
Flex Pipe
90deg
Elbow
90deg
Elbow
90deg
Elbow
Termination
Snorkel
Termination
Flush
Termination
VLWB-8
Option
Option
Horizontal Installed
Linear Power Vent
Horizontal Run Flex Pipe
Vertical
Flex Pipe
90deg
Elbow
90deg
Elbow
Termination
6’-0”
Max.
LDVPV58
Note: Images are shown without screens for clarity purposes.
However, your replace should not be operated without proper
installation of screens.
WARNING
All venting material must be Montigo flex pipe, with as few joints
as possible. All joints use MVA vent splice. Montigo will not be
held responsible for any water damage that may occur from not
installing the equipment as specified by this document.

H36PVN Power Vent Indoor Gas Fireplace
Page 19
XG0649 - 080921
InstallationInstallation
Venting Components
The following venting components and associated Montigo
part numbers are available for the LDVPV58:
Connection and installation of the vent components
should adhere to the following guidelines:
Connect all vent sections using a minimum of three sheet
metal screws on the outer pipe ue.
Ensure the pipe ends male to female slide in a minimum
of 1 1/2" of overlap.
Ensure all runs are supported with a minimum of 3 supports
per 10’ of venting.
When hanging/ supporting venting, ensure that 1” clearance
is maintained on all sides to any combustible material.
Ensure when cutting sections of rigid pipe to maintain
integrity of internal supports.
Place the springs, supplied with the pipe kit, between the
outer and inner pipes to keep the pipes separate and avoid
any possible hot spots.
Montigo recommends the use of a ex section for the nal
pipe connected directly to the replace o󰀨ering greater
exibility of installation and absorption of movement.
A - Termination DVPV58
C - Control Module
D - Flex Sections
G - Power Cord
Harnesses:
F - Elbows
B - Power Vent LDVPV58
RHSIT05
EPVH10 -10 foot power cord and harness
EPVH20 -20 foot power cord and harness
EPVH30 -30 foot power cord and harness
EPVH40 -40 foot power cord and harness
EPVH50 -50 foot power cord and harness
EPVH60 -60 foot power cord and harness
EPVH70 -70 foot power cord and harness
EPVH80 -80 foot power cord and harness
EPVH90 -90 foot power cord and harness
EPVH100 -100 foot power cord and harness
PEL-90MM (m/m 90° Elbow)
PEL-90FF (f/f 90° Elbow)
PEL-90FM (f/m 90° Elbow)
PEL-45FM (f/m 45° Elbow)
E - Rigid Sections PEXT - 1 (12" m/f Section)
PEXT - 2 (24" m/f Section)
PEXT - 3 (36" m/f Section)
PEXT - 4 (48" m/f Section)
PXT-20 (20" section)
PFL-1 (12" Section)
PFL-2 (24" Section)
PFL-3 (36" Section)
PFL-4 (48" Section)
Note: Images are shown without screens for clarity purposes.
However, your replace should not be operated without proper
installation of screens.

H36PVN Power Vent Indoor Gas Fireplace
Page 20 XG0649 - 080921
InstallationInstallation
Installation of the LDVPV58 power vent module:
1. The linear power vent can be installed to existing stud
construction or directly to cement wall or roof. The LDVPV58
must maintain the clearance to combustibles as shown in Figure
9a. The required service access panel must be framed at 28"
X 18". To enclose the service access panel, (at less than 2") a
minimum 30% free air must be supplied at all times.
2. Plug the power cord into the available slot in the linear power
vent.
3. Secure all venting joints with at least three screws and ensure
that the joints are properly sealed.
Figure 9. LDVPV58 Power Vent overall dimensions.
Top View Side View
Figure 9b.LDVPV58 Power Vent framing dimensions.
Framing Dimensions
Figure 9a.LDVPV58 Power Vent framing dimensions.
The VLWB-8 termination is
designed to be installed ush
with the exterior of the building.
This recessed design uses 5"/8"
vent and allows the installation to
be clean and ush so it does not
interfere or have an impact with
your architectural design.
NOTE:
TheH36PVN requires a specic volume of atmospheric interchange
to operate properly and e󰀩ciently
 The replace requires a MIN 80in/sq. air movement to function.
 The grille must also be able to shed water, not allowing any
moisture to enter the unit.
Recessed Termination Installation (VLWB-8) Refer to Appendix A -
Termination locations
Figure 10. Linear Power Vent recessed Termination.
13 5/16"
21 3/8"
18 1/8"
58
20 3/16"
12 9/64"
7 13/16" 2
1
ISOMETRIC VIEW
(NTS)
NTS
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
VLWB-8
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
LF
DATE
NAME
7/29/2010
304 S.S.T.
TERMINATION, VERTICAL MOUNT, 5/8", 12" X 20" BOX
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Z:\CADD\2007 CADD\Standard\TERMINATIONS\VERTICAL TERMS\VLWB-8\VLWB-8
Thursday, July 29, 2010 10:14:21 AM
SCALE
Access Cover
16 1/2
33 8
11
34 7/8
Access Cover
181/2
28 clearance
for Cover access
5 MIN
5 MIN
Must be left clear on both
ends of Power Vent for
adequate ventilation.
2 MIN
5
MIN
5
MIN
1/2
MI
N
Louvres
Vent