Montigo PVHFL58-300 Instruction Manual

IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor's phone. Follow the gas
supplier's instructions.
If you cannot reach your gas supplier, call the fire department.
DANGER
Irritant
Cutting
Watchyour step
Slipperyfloor
Hightemperatures
Glasshazard
Dangerof suffocation
Highvoltage
Toxic
Flammablematerials
Corrosive
Forklift trucks
Dangeroverhead crane
Explosionrisk
Oxidising
Dangerof death
Biohazard
LaserRadiation
Dangerof entrapment
Hotsurface
GeneralWarning
Blank
Gasbottles
Watchfor
fallingobjects
Electricity
Dangerfor cutter
Entrapmenthazard
Batteryhazard
Rotatingparts
Lowtemperature
Strongmagnetic field
Opticalradiation
Nonionizing
radiation
Radiation
Hazardousto the
Environment
Dangerof harming
yourhands
Irritant
Cutting
Watchyour step
Slipperyfloor
Hightemperatures
Glasshazard
Dangerof suffocation
Highvoltage
Toxic
Flammablematerials
Corrosive
Forklift trucks
Dangeroverhead crane
Explosionrisk
Oxidising
Dangerof death
Biohazard
LaserRadiation
Dangerof entrapment
Hotsurface
GeneralWarning
Blank
Gasbottles
Watchfor
fallingobjects
Electricity
Dangerfor cutter
Entrapmenthazard
Batteryhazard
Rotatingparts
Lowtemperature
Strongmagnetic field
Opticalradiation
Nonionizing
radiation
Radiation
Hazardousto the
Environment
Dangerof harming
yourhands
Irritant
Cutting
Watchyour step
Slipperyfloor
Hightemperatures
Glasshazard
Dangerof suffocation
Highvoltage
Toxic
Flammablematerials
Corrosive
Forklift trucks
Dangeroverhead crane
Explosionrisk
Oxidising
Dangerof death
Biohazard
LaserRadiation
Dangerof entrapment
Hotsurface
GeneralWarning
Blank
Gasbottles
Watchfor
fallingobjects
Electricity
Dangerfor cutter
Entrapmenthazard
Batteryhazard
Rotatingparts
Lowtemperature
Strongmagnetic field
Opticalradiation
Nonionizing
radiation
Radiation
Hazardousto the
Environment
Dangerof harming
yourhands
Irritant
Cutting
Watchyour step
Slipperyfloor
Hightemperatures
Glasshazard
Dangerof suffocation
Highvoltage
Toxic
Flammablematerials
Corrosive
Forklift trucks
Dangeroverhead crane
Explosionrisk
Oxidising
Dangerof death
Biohazard
LaserRadiation
Dangerof entrapment
Hotsurface
GeneralWarning
Blank
Gasbottles
Watchfor
fallingobjects
Electricity
Dangerfor cutter
Entrapmenthazard
Batteryhazard
Rotatingparts
XG0519 070714
PVHFL58-300 &
PVHFL510-300
5/8 and 5/10
Horizontal Flush
Louvered
Power Vent
Installation & Maintenance Manual
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.
NOTICE
If the information in these instructions is not followed exactly, a fire or explosion
may result causing property damage, personal injury or death.
WARNING
Canadian Heating Products Inc. Langley, BC V4W 4A1 | Montigo Del Ray Corp. Ferndale, WA 98248
This power vent is approved for use with Montigo fireplaces only and is certified to
ANSI Z21.50 / CSA 2.22 vented gas fireplace standard along with the fireplace.
NOTICE
PVHEX58-300 power vent is approved for use with Montigo R320, R320-ST, R420,
R420-ST, and RP620.
NOTICE
PVVEX58-300 power vent is approved for use with Montigo R320, R320-ST, R420,
R420-ST, and RP620.
NOTICE
PVHFL58-300 power vent is approved for use with Montigo R320, R320-ST, R420,
R420-ST, and RP620.
NOTICE
PVHEX510-300 power vent is approved for use with Montigo R520, R520-ST,
R620-ST, R720, and R820.
NOTICE
PVVEX510-300 power vent is approved for use with Montigo R520, R520-ST,
R620-ST, R720, and R820.
NOTICE
PVHFL510-300 power vent is approved for use with Montigo R520, R520-ST,
R620-ST, R720, and R820.
NOTICE

Introduction
Specications
General Information
This installation guide covers installation of the External Power Vent
System only. This system is designed to allow installation of gas replaces
that cannot be done with a standard Direct Vent gas replace installa-
tion. Only for use on R-Series, R-Series See-Through and RP-Series.
ONLY USE WITH APPROVED FIREPLACES - see replace
installation manual.
Read through the replace's installation & maintenance manual, as it
must also be adhered to.
Power Cord Harnesses:
EPVH10 - 10 foot power cord and harness
EPVH20 - 20 foot power cord and harness
EPVH30 - 30 foot power cord and harness
EPVH40 - 40 foot power cord and harness
EPVH50 - 50 foot power cord and harness
EPVH60 - 60 foot power cord and harness
EPVH70 - 70 foot power cord and harness
EPVH80 - 80 foot power cord and harness
EPVH90 - 90 foot power cord and harness
EPVH100 -100 foot power cord and harness
Before Your Begin
For vent congurations and power vent locations,
refer to replace manual.
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent
Safety Alert Key
Page 2 XG0519 - 070714
Pipe Dimensions PVHFL58-300 ............5"/8"
Pipe Dimensions PVHFL510-300 ..........5"/10"
Maximum Airow: ......................... 300 CFM
Speed: .......................................... 2700 RPM
Power: ............................................ Connect to replace control box
............................................ Refer to replace rating plate

Product Dimensions
Introduction
Figure 1. PVHFL58-300 (Tolerance ±⅛") [mm]
Front View
Side View
18
3
4
"
476
22 1
4
"
565
21 1
8
"
538
12 1
4
"
311
5"
126
8"
203
2"
50
24 5
8
"
627
16 5
8
"
421
PVHFL58-300 Flush Louvered Power Vent
18 3
4
"
476
22 1
4
"
565
21 1
8
"
538
12 1
4
"
311
5"
126
8"
203
2"
50
24 5
8
"
627
16 5
8
"
421
PVHFL58-300 Flush Louvered Power Vent
Top View
Back Cover / Collar
Outer Assembly
Inner Assembly
Louver Assembly
18 3
4
"
476
22 1
4
"
565
Framing
Wall Board
Outer Vent
Assembly
Step 1
1) Construct the support framing within the
measurements as shown here. The
dimensions shown here are minimum
dimensions to attach the Outer Assembly too.
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent
21 1
8
"
538
12 1
4
"
311
5"
126
PVHEX58-300
8"
203
PVHEX10-300
10"
254
Page 3
XG0519 - 070714

Installing the power vent
18 3
4
"
476
22 1
4
"
565
Framing
Wall Board
Outer Can
Assembly
Figure 2. Framing dimensions
Installation
Step 1: Unpack power vent from box. Remove two screws from bottom of the
door. Hold louver assembly securely so it does not fall.
Figure 3.
Step 2: Remove the louver assembly by lifting the bottom end forward and
then dropping the door out of the top latches.
Figure 3a.
Step 3: To remove the inner can from the outer can remove the 8 screws on
the back of the termination.
Figure 3b.
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent
Page 4 XG0519 - 070714

Installation
Page 5
XG0519 - 070714
Step 4: Slide the inner can out by pulling
Figure 3c.
Step 5: Screw outer can assembly into the wall
18 3
4
"
476
22 1
4
"
565
Framing
Wall Board
Outer Can
Assembly
Figure 3d.
Step 6: Slide the inner can assembly into the outer can assembly from the
inside of the house.
Structure
Outer Can Assembly
Inner Can Assembly
Power Cord from Power Vent
Figure 3e.
Step 7: Screw inner can back to outer can using 8 screws.
Figure 3f.
All framing shown is combustible
All framing shown
is combustible
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent

Installation
Page 6 XG0519 - 070714
Step 8: Remove two screws securing electrical plate.
Figure 3g.
Step 9: Remove the power vent power cable from inside the electrical
channel.
Figure 3h.
Step 10:Take the electrical harness [EPVH-10-100] that will communicate
with the power vent and attach the strain relief for it to the electrical plate.
Tighten the nut on the strain relief.
Figure 3i.
Step 11: Attach the power cable from the power vent to the control cable.
Figure 3j.
Step 12: Push all the excess cable back into the electrical channel of the
power vent. Screw the electrical plate back on the power vent.
Figure 3j.
Figure 3k.
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent

Installation
Page 7
XG0519 - 070714
Louver
Assembly
Tabs
Screw
Locations
Step 3:
1) Place Front Grill into the Out Can
Assembly by inserting top tabs into the
upper frame and securing the bottom with
2 screws provided.
Step 13: Reinstall the door.
Figure 3l.
Step 14: Connect vent pipe to power vent collar as required.
Note: If you are intending to service power vent from inside the house, use a
4-foot ex pipe to allow for easy removal of pipe from power vent.
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent
Conduit & Wiring clearances
Connect the power vent harness as outlined. Connect the wiring to
the replace as outlined in the schematic shown in gure 4a. Ensure
that the proper clearances are maintained for the wiring and conduit.
When installing the wiring it must never run above the vent run and it
must be at least 1" clear of all venting.
1” Clearance
Wire
Figure 4. Conduit and Wiring
Wiring Installation

Service
Page 8
XG0519 - 070714
C
Power Vent Wiring
BLUE
BROWN
BLACK WHITE
BLACK
GREEN
6 PIN MOLEX
CONNECTOR
KEY WAY
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent
Figure 4a.

Installation
Page 9 XG0519 - 070714
Figure 4b.
v
v
FIXED
CLOSED
OPERABLE
F
C
B
v
v
OPERABLE FIXED
CLOSED
v
B
X
B
A
B
J
H
I
X
K
v
M
V
B
L
D
E
V
INSIDE
CORNER DETAIL
v
G
A
VVENTER TERMINAL XAIR SUPPLY INLET AREA WHERE TERMINAL IS
NOT PERMITTED
PVHEX58 300
A= Clearance above grade, veranda,
porch, deck, or balcony
12 in (30 cm) 12 in (30 cm)
Canadian Installations US Installations
1 2
B= Clearance to window or door that
may be opened
6 in (15 cm) for appliances <
10,000 Btuh (3 kW), 12 in
(30 cm) for appliances >
10,000 Btuh (3 kW) and <
100,000 Btuh (30 kW), 36 in
(91 cm) for appliances >
100,000 Btuh (30 kW)
6 in (15 cm) for appliances <
10,000 Btuh (3 kW), 9 in
(23 cm) for appliances >
10,000 Btuh (3 kW) and <
50,000 Btuh (15 kW), 12 in
(30 cm) for appliances >
50,000 Btuh (15 kW)
C= Clearance to permently closed
window B B
15 in (38 cm)
D= Vertical clearance to ventilated
soffit located above the terminal within
a horizontal distance of 2 feet (61 cm)
from the center line of the terminal
15 in (38 cm)
E= Clearance to unventilated soffit 15 in (38 cm) 15 in (38 cm)
F= Clearance to outside corner 6 in (15 cm) 6 in (15 cm)
G= Clearance to inside corner 15 in (38 cm) 15 in (38cm)
H= Clearance to each side of center
line extended above meter/regulator
assembly
3 ft (91 cm) within a height 15
ft. (4.5 m) above the meter/
regulator assembly
*
I= Clearance to service regulator
vent outlet
3 ft (91 cm)
*
J= Clearance to nonmechanical air
supply inlet to building or the
combustion air inlet to any other
appliance
6in (15 cm) for appliances <
10,000 Btuh (3 kW), 12 in (30
cm) for appliances > 10,000
Btuh (3 kW) and < 100,000
Btuh (30 kW), 36 in (91 cm)
for appliances > 100,000
Btuh (30 kW)
Canadian Installations US Installations
1 2
6in (15 cm) for appliances <
10,000 Btuh (3 kW), 9 in (23
cm) for appliances > 10,000
Btuh (3 kW) and < 50,000
Btuh (15 kW), 12 in (30 cm)
for appliances > 50,000 Btuh
(15 kW)
K= Clearance to a mechanical air
supply inlet
6 ft (1.83 m) 3 ft (91 cm) above if within 10
ft (3 m) horizontally
L= Clearance above paved sidewalk
or paved driveway located on
public property
7 ft (2.13 m)
*
M= Clearance under veranda porch
deck, or balcony
12 in (30 cm)
*
1 In accordance with the current CSA B149.1, Natural Gas and Propane Installation Code
2 In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code
A vent shall not terminate directly above a sidewalk or paved driveway that is located between two
single family dwellings and serves both dwellings.
Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath
the floor.
* For clearances not specified in ANSI Z223.1/NFPA or CSA B149.1, one of the following shall be
indicated
a) A minimum clearance value determined by testing in accordance with section 2.23.5, or;
b) A reference to the following footnote:
"Clearance in accordance with local installation codes and the requirements of the gas supplier"
See Fireplace Installation Guide
See Fireplace Installation Guide
See Fireplace Installation Guide
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent

Service
Page 10
XG0519 - 070714
Step 3: Remove the louver assembly by lifting the bottom end forward and
then dropping the door out of the top latches.
Figure 5a.
Step 4: Remove the three screws securing the rain guard.
Figure 5.
Figure 5b.
Go to Capacitor or Motor and Capacitor Replacement Section.
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent
Servicing
From the outside of the house
Step 1: Turn off gas and power.
Step 2: Remove two screws from the bottom of the louver assembly.
Caution: Hold the louver assembly securely so it does not fall.

Step 1: Reinstall the rain guard using the supplied 3 screws.
Figure 6.
Service
Page 11 XG0519 - 070714
Louver
Assembly
Tabs
Screw
Locations
Step 3:
1) Place Front Grill into the Out Can
Assembly by inserting top tabs into the
upper frame and securing the bottom with
2 screws provided.
Step 2: Reinstall door with supplied 2 screws.
Figure 6a.
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent
Reinstalling from the outside

Service
Page 12
XG0519 - 070714
Figure 7a.
Figure 7b.
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent
Servicing
From the inside of the house
Step 1: Turn off gas and power.
Step 2: Disconnect venting from the power vent
Vent Termination
Venting
Rear Panel
Screw Locations
x8 places
Outer Case
Screw Locations
2x places
Rain Guard
Fan Motor Gasket
Screw Locations
8x places
Fan Motor
Assembly
Fan Motor Capacitor
Step 1:
a) Remove the screws holding
the venting to the rear of the
termination. Pull the vent
away from the termination.
PVHFL5-300
Motor Removal / Servicing (from inside)
Step 2:
a) Remove the screws holding
the Rear Panel on the
Termination.
b) Slide the Inner Blower
Assembly out of the Outer
Case
Inner Blower
Assembly
Step 3:
a) Remove 2 upper screws and
remove Rain Guard.
Step 4:
a) Replace the Fan Motor
Assembly.
b) Re-attach wires as required.
c) We recommend changing
the Motor Capacitor as well.
d) Make sure the Fan Motor
Gasket is in place.
e) Re-assemble the entire
termination in the reverse
itemized above.
Figure 7.
Step 3: Remove two screws securing the electrical plate.
Step 4: Pull electrical plate off the power vent and pull the molex
connection out of the electrical channel. Disconnect the molex.
Step 5: Remove 8 screws securing the inner can assembly to the
outer can assembly.
Figure 7c.
Step 6: Slide the inner can out by pulling. Place the inner can as-
sembly somewhere to work.
Figure 7d.

Step 7: Remove the three screws securing the rain guard.
Go to Capacitor or Motor and Capacitor Replacement Section.
Service
Page 13 XG0519 - 070714
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent
Figure 7e.

Service
Page 14
XG0519 - 070714
Step 3: Secure inner can to the outer can with supplied 8 screws.
Figure 8b.
Figure 8c.
Step 4: Plug control cable back into power vent power cable.
Figure 8d.
Step 5: Stuff excess wire back into electrical channel and secure
electrical plate with supplied two screws.
Step 6: Reconnect venting to the power vent.
Step 7: Check spin and operation of power vent from outside.
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent
Reinstalling the inner can
From the inside of the house
Step 1: Screw the rain guard back on with the supplied 3 screws.
Figure 8.
Step 2: Slide the inner can into the outer can
Figure 8a.
Vent Termination
Venting
Rear Panel
Screw Locations
x8 places
Outer Case
Screw Locations
2x places
Rain Guard
Fan Motor Gasket
Screw Locations
8x places
Fan Motor
Assembly
Fan Motor Capacitor
Step 1:
a) Remove the screws holding
the venting to the rear of the
termination. Pull the vent
away from the termination.
PVHFL5-300
Motor Removal / Servicing (from inside)
Step 2:
a) Remove the screws holding
the Rear Panel on the
Termination.
b) Slide the Inner Blower
Assembly out of the Outer
Case
Inner Blower
Assembly
Step 3:
a) Remove 2 upper screws and
remove Rain Guard.
Step 4:
a) Replace the Fan Motor
Assembly.
b) Re-attach wires as required.
c) We recommend changing
the Motor Capacitor as well.
d) Make sure the Fan Motor
Gasket is in place.
e) Re-assemble the entire
termination in the reverse
itemized above.

Service
Page 15 XG0519 - 070714
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent
Capacitor Replacement
REC 1250 Note: Maintenance must be preformed by qualied personnel/
electrician
Figure 9.
Step 1: Cut the two zap straps securing the wiring.
Figure 9a.
Step 2: Cut the brown wire from the motor.
Figure 9b.
Step 3: Cut bre white wire from power cable, black wire from capacitor and
black wire from motor.
Figure 9c.
Step 4: Unscrew mounting screw securing capacitor and remove capacitor.
Figure 9d.
Step 5: Strip all wire ends. Secure new capacitor with mounting screw.
Figure 9e.

Service
Page 16
XG0519 - 070714
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent
Step 6: Using the large bell connector, connect the black bre wire from the
power cable to the black wire from the motor and the black wire from the
capacitor.
Figure 9f.
Step 7: Using the small bell connector, connect the brown wire from the mo-
tor to the black wire from the capacitor.
Figure 9g.
Step 8: Secure the wiring neatly with the supplied zap straps. Check that the
power vent operates and spins counterclockwise. Note: When replacing from
the inside you will need to reinstall the power vent and check spin from the
outside. Note: Ensure wires are secured away from moving parts
Figure 9h.
Go to reinstalling either from outside or inside.

Service
Page 17 XG0519 - 070714
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent
Motor and Capacitor Replacement
REC 1251 Note: Maintenance must be preformed by qualied personnel/
electrician
Figure 10.
Step 1: Cut the two zap straps securing the wiring.
Figure 10a.
Step 2: Cut the brown wire from the motor.
Figure 10b.
Step 3: Cut bre white wire from power cable, black wire from capacitor and
black wire from motor.
Figure 10c.
Step 4: Cut the black ber wire from the power cable.
Figure 10d.
Step 5: Unscrew mounting screw securing capacitor and remove capacitor.
Figure 10e.

Service
Page 18
XG0519 - 070714
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent
Step 6: Unscrew 8 screws securing the motor mounting plate.
Figure 10f.
Step 7: Remove the motor.
Figure 10g.
Step 8: Install the new motor.
Figure 10h.
Step 9: Secure motor mounting plate with supplied 8 screws & star washers.
Figure 10i.
Step 10: Secure new capacitor with supplied screw.
Figure 10j.
Step 11: Using suppled small bell connector, connect the blue wire from the
motor to the black bre wire from the power cable.
Figure 10k.

Service
Page 19 XG0519 - 070714
Go to reinstalling either from outside or inside.
PVHFL58-300 & PVHFL510-300 Horizontal Power Vent
Step 13: Using the other supplied small bell connector, connect the brown
wire from the motor to the black wire of the capacitor.
Figure 10m.
Step 14: Secure the wiring neatly with the supplied zap straps. Check that
the power vent operates and spins counterclockwise. NOTE: When replacing
from inside you will need to reinstall the power vent and check spin from the
outside. Note: Ensure wires are secured away from moving parts
Figure 10n.
Step 12: Using the other supplied large bell connector, connect the white
bre wire from the power cable to the black wire from the capacitor and the
black wire from the motor.
Figure 10l.

PVHFL58-300 & PVHFL510-300 Horizontal Power Vent
Appendix A: Warranty
The Warranty
The Companies warrants the Montigo Gas Appliance to be free from defects in materials and workmanship at the time of manufacture. On the Montigo replace,
there is a ten-year warranty on the rebox and its components, a ve-year warranty on the main burner and pilot burner, and a one-year warranty on the gas control
valve, bre logs and Power Vent Module. The Glass, plated / painted nishes, and refractory lining are exempt from the warranty.
Remedy And Exclusions
The coverage of this Warranty is limited to all components of the Gas Appliance manufactured by The Companies.
This Warranty only covers Montigo Gas Appliances installed in the United States or Canada.
If the components of the Gas Appliance covered by this Warranty are found to be defective within the time frame stated (see The Companies right of investigation
outlined below). The Companies will, at its option, replace or repair defective components of the Gas Appliance manufactured by The Companies at no charge,
and will also pay for reasonable labour costs incurred in replacing or repairing components. If repair or replacement is not commercially practical, The Companies
will, at its option, refund the purchase price of the Montigo Gas Appliance.
This Warranty covers only parts and labour as provided above. In no case shall The Companies be responsible for materials, components, or construction which
are not manufactured or supplied by The Companies, or for the labour necessary to install, repair or remove such materials, components or construction. All
replacement or repair components will be shipped F.O.B. the nearest The Companies factory.
Qualications To The Warranty
The Gas Appliance Warranty outlined above is further subject to the following qualications:
(1) The Gas Appliance must be installed in accordance with The Companies installation instructions and local building codes. The Warranty on this Montigo
Gas Appliance covers only the component parts manufactured by The Companies. The use of components manufactured by others with this Montigo Gas
Appliance could create serious safety hazards, may result in the denial of certication by recognized national safety agencies, and could be in violation of
local building codes. This warranty does not cover any damages occurring from the use of any components not manufactured or supplied by The Companies
(2) The Montigo Gas Appliance must be subjected to normal use. The Gas Appliances are designed to burn gas only. Burning conventional replace fuels such
as wood, coal or any other solid fuel will cause damage to the Gas Appliance, will produce excessive temperatures and will result in a re hazard.
Limitations On Liability
It is expressly agreed and understood that The Companies sole obligation, and purchaser's exclusive remedy under this Warranty, under any other warranty,
expressed or implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specied above.
In no event shall The Companies be responsible for any incidental or consequential damages caused by defects in its products, whether such damage occurs
or is discovered before or after replacement or repair, and whether or not such damage is caused by The Companies negligence. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. The duration of any implied warranty
with respect to this Montigo Gas Appliance is limited to the duration of the foregoing warranty. Some states do not allow limitation on how long an implied warranty
lasts, so the above may not apply to you.
Investigation Of Claims Against Warranty
The Companies reserves the right to investigate any and all claims against this Warranty and to decide upon method of settlement.
The Companies Are Not Responsible For Work Done Without Written Consent
The Companies shall in no event be responsible for any warranty work done without rst obtaining The Companies written consent.
Dealers Have No Authority To Alter This Warranty
The Companies employees and dealers have no authority to make any warranties nor to authorize any remedies in addition to or inconsistent with those stated above.
How To Register A Claim Against Warranty
In order for any claim under this Warranty to be valid, The Companies must be notied of the claimed defect in writing or by telephone, as soon as reasonably
possible after the defect is discovered. Claims against this Warranty in writing should include the date of installation, and a description of the defect.
Other Rights
This Warranty gives you specic legal rights, and you may also have other rights which vary from state to state.
NOTE: The Companies as stated above refer to - Canadian Heating Products Inc. and/or Montigo Del Ray Corp.
Canadian Heating Products Inc. and/or Montigo DelRay Corp. reserves the right to make changes at any time, without notice, in design, materials,
specications, prices and also to discontinue colors, styles and products.
Appendix
Page 20 XG0519 - 070714